Thesis (Ph. D.)--Lehigh University, 2005. / Includes vita. Includes bibliographical references (leaves 127-137).

Thesis (Ph.D.)--University of Nebraska-Lincoln, 2006. / Title from title screen (site viewed on Jan 23, 2007). PDF text: 303 p. : ill. (some col.) ; 2.13Mb. UMI publication number: AAT 3216338. Includes bibliographical references. Also available in microfilm and microfiche format.

Thesis (Ph. D.)--Oregon State University, 2006. / Printout. Includes bibliographical references (leaves 97-105). Also available on the World Wide Web.

Thesis (M.Phil.)--Hong Kong University of Science and Technology, 2007. / Includes bibliographical references (leaves 49-52). Also available in electronic version.

Thesis (M.S.)--Montana State University--Bozeman, 2009. / Typescript. Chairperson, Graduate Committee: Richard Wolff. Includes bibliographical references (leaves 74-76).

M.Ing. / In this dissertation the emphasis falls on the use of the 1550 run WDM systems that make use of standard single-mode fibre. The reason for this is that more than 50 million kilometres of standard telecommunication fibre is already installed in the worldwide telephone network. Therefore, from an economical point of view, the fourth generation of lightwave systems has to make use of this existing base. Using single-mode fibre at high bit-rate (- 10 Gb/s) dispersion becomes a problem. Furthermore, if amplifiers are used, as in the case of long-haul WDM systems, non-linear effects also become important although the input power levels are low (-1 mW). Thus, the system performance is influenced by both the dispersion problem and fibre non-linearities. In this dissertation the influence of these effects was investigated and the use of different dispersion management schemes was considered in order to minimise the dispersion and the effects of these non-linearities on the optical signals. It was seen that by using pre-compensation, the optical pulses would become narrower whereas by using post-compensation, the pulses would be broader than the original input pulses. Thus, the combined effect of fibre non-linearity and fibre dispersion led to the fact that the order in which dispersion compensation is realised is important. By using symmetrical dispersion compensation that is defined as a dispersion compensation scheme that makes use of an equal amount of pre- and post-compensation sections, the tendency of pulse narrowing and pulse broadening can be balanced. It was found from simulations, that pre-compensation led to a smaller SPM penalty than postcompensation, whereas in the case of cross-phase ,modulation, the opposite is true. Using lumped dispersion compensation at the,en(f:o£ the system, it was found that both SPM and XPM penalties could be minimised. It was found that negative and positive lumped dispersion compensation could be used to improve the system perfortriance of pre- and post compensation schemes respectively. The performance of symmetrical compensation also improved by using a positive lumped dispersion compensation regarding SPM penalty, but in the case of XPM penalty, it was found that lumped dispersion compensation could not be used to improve this penalty. Furthermore, the effect of not using 100% dispersion compensation per span on the system performance was determined. From simulations, it followed that under-compensation will lead to an improvement in the system performances of the post- and symmetrical dispersion compensation, whereas an over-compensation will lead to an improvement in the precompensation case. It was also shown that XPM index penalty decreases in all of these dispersion compensation schemes if 100% compensation per span is not used. The reason for this is the inter -span walk-off that reduces the XPM distortion by reducing the localised buildup of phase distortions. Finally, it was shown that by independently controlling the input power levels in the SMF and DCF the best system performance is possible. Furthermore, by making use of lumped dispersion compensation or by not using 100% dispersion compensation per span, the system performance of the pre-, post- and symmetrical dispersion conipensation schemes can be improved quite a lot. Comparing the results of the pre-, post- and symmetrical dispersion compensation schemes that made use of independent control of power levels with the pre-, post- and symmetrical dispersion compensation schemes that did not use independent control ofpower levels, the Q factors were improved from 6.2 to 8, from 5.4 to 9 and from 7.5 to 11 in each case respectively.

No description available.

A new multiplexing technique based on the orthogonality of the signal waveform is proposed. It can bring extra capacity to the existing fiber-optic communication system. / A new multiplexing technique is proposed in this work, which is a promising alternative technique for next-generation high-capacity fiber-optic communication system. The concept of this technique is based on the orthogonality of the signal waveform. / Thesis / Master of Science (MSc) / A number of signals with orthogonal waveforms are multiplexed into a single optical fiber. In this scheme, the user’s information is encoded into the amplitude and the phase of the signal waveform. Then multiplexed signals can be transmitted through the fiber-optic communication system.

Photonic crystals (PCs) are nano-structured materials in which a periodic variation of the dielectric constant of the material results in a photonic band gap. By introducing defects into PCs, it is possible to build waveguides that can channel light along certain paths. It is also possible to construct micro-cavities that can localize photons in extremely small volumes. In this dissertation, to begin with, we computed the photonic crystals dispersion relations and found the photonic band gap (PBG) by the plane wave expansion method (PWE) in the frequency domain. Then, the finite difference time domain method (FDTD) along with the perfectly matched layer boundary conditions was adopted to solve Maxwell¡¦s equations, equivalent to simulate the movement behavior of the Photonic crystals. By properly varying the size of the defect on the PCs, it could really drop the particular wavelengths and guide them to output channels by PCs waveguides. We proposed the structures that would function as Wavelength-Division-Multiplexer (WDM). Secondly, coupled cavity waveguide of PC was used to control group velocity that achieved the slow light property. By calculating dispersion curve with PWE, we obtained group velocity characteristics in PCs waveguide. Meanwhile, we designed a novel Time-Division-Multiplexer (TDM) system by controlling the group velocity characteristics. Finally, we designed cascade ring resonators and expected to obtain an extendable delay line. Conventional delay line devices are propagating in a long waveguide to obtain the delay line property. An excellent delay line and ultra-small size properties are expected in the proposed structure. Because nano-technology has been making great progress steadily, it surely can be used to demonstrate a practical breakthrough in which the devices based on the PC integrated circuits are realized. These devices will be a potential key component in the applications of ultra-high-speed and ultra-high-capacity optical communications and optical data processing systems.

Thesis (Ph.D.)--Hong Kong University of Science and Technology, 2008. / Includes bibliographical references (p. 178-187).