Isotactic polypropylene (iPP) is one of the widely used commercial thermoplastics. Physical properties of iPP can be tailored to the requirements with respect to structure, microstructure and processing, thus research continues in the development and modification of the polymer. With the advancement of chemistry, as our understanding in tailoring of the molecular structure has enhanced, iPP has become more of a generic name.

The effect of various inorganic and organic additives as possible nucleating agents on the crystallisation behaviour of P. E. T. and the suosequent influence on the morphological and mechanical properties has been examined. Various methods of mixing(: the polymer and additive were investigated and a method involving the screw-Extrusion of the polymer and the additive was ultimately adopted. Crystallisation studies were carried out using differential scanning calorimetry under dynamic and isothermal modes. The results produced under conditions of isothermal crystallisation were analysed by means of a computer. Despite differences between batches of polymer all the additives with the exception of indigo produced a nucleating effect in the polymer as indicated by an increase in the rate of crystallisation compared with that of the base polymer. Two organo-metallic substances (sodium benzoate and sodium stearate) proved to be the most effective in this respect by decreasing the degree of supercooling of the polymer by 20 [degrees]. Morphological studies were carried out on isothermally crystallised samples, after etching and replication using a transmission electron microscope. A nodular structure whose dimensions were sensitive to both the nucleating agent and the temperature of crystallisation was observed. Mechanical testing of samples direct from the D. S. C. was carried out using a compression method. The breaking loads were found to vary with both the type of nucleating agent used and the crystallisation temperature chosen. A separate study involving the exanination of the resulting fracture surfaces by scanning electron microscopy revealed that a, high breaking load was associated with a fine discontinuous structure whereas lower breaking loads were characterised by a more continuous linear appearance. This implies a higher energy of fracture due to the increased surface area of the fracture surface of the former.

The effect of various inorganic and organic additives as possible nucleating agents on the crystallisation behaviour of P. E. T. and the suosequent influence on the morphological and mechanical properties has been examined. Various methods of mixing(: the polymer and additive were investigated and a method involving the screw-Extrusion of the polymer and the additive was ultimately adopted. Crystallisation studies were carried out using differential scanning calorimetry under dynamic and isothermal modes. The results produced under conditions of isothermal crystallisation were analysed by means of a computer. Despite differences between batches of polymer all the additives with the exception of indigo produced a nucleating effect in the polymer as indicated by an increase in the rate of crystallisation compared with that of the base polymer. Two organo-metallic substances (sodium benzoate and sodium stearate) proved to be the most effective in this respect by decreasing the degree of supercooling of the polymer by 20 [degrees]. Morphological studies were carried out on isothermally crystallised samples, after etching and replication using a transmission electron microscope. A nodular structure whose dimensions were sensitive to both the nucleating agent and the temperature of crystallisation was observed. Mechanical testing of samples direct from the D. S. C. was carried out using a compression method. The breaking loads were found to vary with both the type of nucleating agent used and the crystallisation temperature chosen. A separate study involving the exanination of the resulting fracture surfaces by scanning electron microscopy revealed that a, high breaking load was associated with a fine discontinuous structure whereas lower breaking loads were characterised by a more continuous linear appearance. This implies a higher energy of fracture due to the increased surface area of the fracture surface of the former.

Diploma thesis is summarizing sources and technology of PHB and its physical and chemical properties compared to other polymers. Thesis mentions usage and function of certain additives in PHB matrix and their impact on the final product. Practical part of the thesis is concerned with technological parameters and degradation of the PHB during extrusion. The thesis also observes behaviour of nucleating agents on crystallinity and crystallization properties of prepared compounds. Degradation was analyzed by MFI and colour difference against standard material, FTIR was not successfully used for the purpose of degradation. Crystallinity and crystallization behaviour was analysed by DSC and optical microscopy with heated operating table. Graphs were created from results of analysis and suitable usage of each nucleating agent was considered. Boron nitride was selected as the most suitable nucleating agent due to creating higher amount of smaller spherulites.

The aim of submitted diploma thesis is the study of non-isothermal crystallization kinetics of polylactide (PLA) with selected agents (1 %) and observation of the emerging crystalline structure under polarizing optical microscope. The agents were talc, a mixture of organic salts with the addition of amorphous SiO2 (HPN 68L) and zinc stearate (HPN 20E) and LAK-301 (potassium salt of 5-dimethylsulfoisophtalate), which is a nucleating agent developer for PLA. The PLA matrix served as a reference. Non-isothermal crystallization took place on a differential scanning calorimeter at cooling rates () 0,3; 0,5; 0,7; 1; 1,5; 2 °C/min After non-isothermal crystallization, the crystalline fraction (Xc) od PLA was evaluated from X-ray diffraction analysis, and the supramolecular structure was observed after chemical degradative etching using confocal laser scanning microscope. The crystallization kinetics were evaluated by the methods of Jeziorny and Mo and the activation energy of the crystallization was determined according to the Friedmann method. All prepared materials were amorphous (Xc 40 % for up to 1,5 °C/min). However, for LAK-301, Xc decreased to 30 % already at the = 2 °C/min and it can be assumed that with increasing its nucleation activity will decrease. A spherulitic structure was observed in all samples, but the number and size of spherulites decreased with increasing and the appearance varied according to the type of agent. Both kinetic models proved to be unsuitable for materials with low Xc and the highest because the rate of crystallization did not change. With the Jeziorny method, it was possible to evaluate the kinetics only for the relative crystallinity Xt = 29–50 % and with the Mo method it was not possible to evaluate the data for the highest for PLA matrix and sample with HPN 68L. The samples with LAK-301 and HPN 68L showed the lowest activation energy.