Ocean wave as a renewable energy source possesses great potential for solving the world energy crisis and benefit human beings. The total theoretical potential wave power on the ocean-facing coastlines of the world is around 30,000 TWh, although cannot all be adopted for generating electricity, the amount of the power can be absorbed still can occupy a large portion of the world's total energy consumption. However, multiple reasons have stopped the ocean wave energy from being widely adopted, and among those reasons, the most important one is immature of the Power Take-off (PTO) technology. In this dissertation, a self-reactive two-body wave energy point absorber that is embedded with a novel PTO using the unique mechanism of Mechanical Motion Rectifier (MMR) is investigated through design, analysis and testing to improve the energy harvesting efficiency and the reliability of the PTO. The MMR mechanism can transfer the reciprocated bi-directional movement of the ocean wave into unidirectional rotation of the generator. As a result, this mechanism brings in two advantages towards the PTO. The first advantage it possess is that the alternating stress of the PTO is changed into normal stress, hence the reliability of the components are expected to be improved significantly. The other advantage it brings in is a unique phenomenon of engagement and disengagement during the operation, which lead to a piecewise nonlinear dynamic property of the PTO. This nonlinearity of the PTO can contribute to an expanded frequency domain bandwidth and better efficiency, which are verified through both numerical simulation and in-lab experiment. During the in-lab test, the prototyped PTO achieved energy transfer efficiency as high as 81.2%, and over 40% of efficiency improvement compared with the traditional non-MMR PTO under low-speed condition, proving the previously proposed advantage. Through a more comprehensive study, the MMR PTO is further characterized and a refined dynamic model. The refined model can accurately predict the dynamic response of the PTO. The major factors that can influence the performance of the MMR PTO, which are the inertia of the PTO, the damping coefficient, and the excitation frequency, are explored through analysis and experiment comprehensively. The results show that the increase on the inertia of the PTO and excitation frequency, and decrease on the damping coefficient can lead to a longer disengagement of the PTO and can be expressed analytically. Besides the research on the PTO, the body structure of the point absorber is analyzed. Due to the low-frequency of the ocean wave excitation, usually a very large body dimension for the floating buoy of the point absorber is desired to match with that frequency. To solve this issue, a self-reactive two-body structure is designed where an additional frequency between the two interactive bodies are added to match the ocean wave frequency by adopting an additional reactive submerged body. The self-reactive two-body structure is tested in a wave to compare with the single body design. The results show that the two-body structure can successfully achieve the frequency matching function, and it can improve more than 50% of total power absorption compared with the single body design. / Doctor of Philosophy / Ocean wave as a renewable energy source possesses great potential for solving the world energy crisis and benefit human beings. The total theoretical potential wave power on the ocean-facing coastlines of the world is around 30,000 TWh, although impossible to be all transferred into electricity, the amount of the power can be absorbed still can cover a large portion of the world's total energy consumption. However, multiple reasons have stopped the ocean wave energy from being widely adopted, and among those reasons, the most important one is immature of the Power Take-off (PTO) technology. In this dissertation, a novel two body wave energy converter with a PTO using the unique mechanism of Mechanical Motion Rectifier (MMR) is investigated through design, analysis, and testing. To improve the energy harvesting efficiency and the reliability of the PTO, the dissertation induced a mechanical PTO that uses MMR mechanism which can transfer the reciprocated bi-directional movement of the ocean wave into unidirectional rotation of the generator. This mechanism brings in a unique phenomenon of engagement and disengagement and a piecewise nonlinear dynamic property into the PTO. Through a comprehensive study, the MMR PTO is further characterized and a refined dynamic model that can accurately predict the dynamic response of the PTO is established. The major factors that can influence the performance of the MMR PTO are explored and discussed both analytically and experimentally. Moreover, as it has been theoretically hypothesis that using a two-body structure for designing the point absorbers can help it to achieve a frequency tuning effect for it to better match with the excitation frequency of the ocean wave, it lacks experimental verification. In this dissertation, a scaled two-body point absorber prototype is developed and put into a wave tank to compare with the single body structure. The test results show that through the use of two-body structure and by designing the mass ratio between the two bodies properly, the point absorber can successfully match the excitation frequency of the wave. The highest power capture width ratio (CWR) achieved during the test is 58.7%, which exceeds the results of similar prototypes, proving the advantage of the proposed design.

As worldwide energy consumption continues to increase, so does the demand for renewable energy sources. The total available wave energy resource for the United States alone is 2,640 TWh/yr; nearly two thirds of the 4,000 TWh of electricity used in the United States each year. It is estimated that nearly half of that available energy is recoverable through wave energy conversion techniques. In this thesis, a two-body 'point absorber' type wave energy converter with a mechanical power-takeoff is investigated. The two-body wave energy converter extracts energy through the relative motion of a floating buoy and a neutrally buoyant submerged body. Using a linear frequency-domain model, analytical solutions of the optimal power and the corresponding power-takeoff components are derived for the two-body wave energy converter. Using these solutions, a case study is conducted to investigate the influence of the submerged body size on the absorbed power of the device in regular and irregular waves. Here it is found that an optimal mass ratio between the submerged body and floating buoy exists where the device will achieve resonance. Furthermore, a case study to investigate the influence of the submerged body shape on the absorbed power is conducted using a time-domain numerical model. Here it is found that the submerged body should be designed to reduce the effects of drag, but to maintain relatively large hydrodynamic added mass and excitation force. To validate the analytical and numerical models, a 1/30th scale model of a two-body wave energy converter is tested in a wave tank. The results of the wave tank tests show that the two-body wave energy converter can absorb nearly twice the energy of a single-body 'point absorber' type wave energy converter. / Master of Science / As worldwide energy consumption continues to increase, so does the demand for renewable energy sources. The total available wave energy resource for the United States alone is 2,640 TWh/yr; nearly two thirds of the 4,000 TWh of electricity used in the United States each year. It is estimated that nearly half of that available energy is recoverable through wave energy conversion techniques. By absorbing the motion of a wave, wave energy converters can turn that energy into useful electricity. A single-body ‘point absorber’ type wave energy converter consists of a floating buoy connected to the seabed by a mechanism called the power-takeoff. The power-takeoff converts the up and down motion of the floating buoy into rotation. A generator is connected to the power-takeoff, which produces useful electricity from the rotation. Issues with the size of the floating buoy, as well as connecting the floating buoy to the seabed, make this design economically impractical. Instead of connecting the floating buoy to the seabed, the floating buoy can be connected to an additional submerged body. In this thesis, optimization strategies were employed on the size and shape of the submerged body to determine theoretical power limits. Here it is found that an optimal mass ratio between the submerged body and floating buoy exists for a given wave profile. It is also found that the optimal shape of the submerged body is long cylindrical body, having a small surface area normal to the motion. A scale model experiment of a two-body wave energy converter was conducted to validate our theoretical models. The results of this experiment are in good agreement with the models, showing that an optimal mass ratio exists for a given wave profile, and that the two-body wave energy converter can absorb nearly twice the energy of a single-body ‘point absorber’ type wave energy converter.