Work had been established for traction machine design aspects in this research. The effect of multiphase design for Permanent Magnet (PM) machine was investigated. The electromagnetic characteristics of both 3-phase and 9-phase machine, along with different magnet designs, were simulated and analyzed by using the program developed during the process. The software used were FEMM and MATLAB. The iron loss for different designs was established, based on the analytical flux density obtained by 2-D stepping FEA method. The harmonic of flux waveform and rotating field were also considered for difference areas in the machine models. The prediction was compared with experimental data collected in open circuit. The simulation result shown that there was a minimum 4% torque gain and noticeable less torque ripples for 9-phase machine, comparing with 3-phase one, with the same excitation phase current. The embedded magnet rotor design was suggested to monitor the demagnetization of each magnet closely, since some area of the magnet could be demagnetized even when the working point of magnet was well distance away from the nonlinear region of its characteristic. There were about 6% less iron loss was produced in 9-phase model than 3-phase model. The implemented method for calculating iron loss was more accurate within 3500 rpm rotor speed comparing with other approaches.

Brushless permanent magnet (PM) drive systems offer a high efficiency over a wide power/torque-speed operating envelope, however, there are a number of problems that may limit, or complicate, their operation particularly in automotive and aerospace vehicular applications, i.e. the loss of control of the power silicon gate drive circuitry during fluxweakening operation, control of high-speed low-inductance machines and the presence of large electrolytic capacitors on the inverter DC link. Current Source Inverters (CSIs) could potentially address some or all of the above issues. However, they have found little application to date due to the wide use of the Voltage Source Inverter (VSI) circuit topology.This thesis investigates feasibility of utilising Current Source Inverters (CSIs) to control permanent magnet synchronous machines in automotive and aerospace actuation systems. CSIs, switching at the fundamental frequency, were used in some of the first semiconductor based, electronic variable speed drive systems that utilised the simple, low maintenance AC induction motor. However, the rapid progress of semiconductors and discovery of Pulse Width Modulation (PWM) techniques soon resulted in the Voltage Source Inverter (VSI) replacing the CSI in all but the highest power applications. Modern power electronics and (micro-processor based) control systems mean that the advantages of VSI systems may no longer be significant and combined with the unique environmental conditions that automotive and aerospace applications present, could allow the CSI to offer advantages over VSIs in these applications.The thesis presents the switching and control logic for CSIs and mapping to the more conventional VSI logic. Analysis is made of the various loss mechanisms in VSI and CSI power circuitary. Simulation models of the VSI and CSI structures are presented and representative drive systems designed, built and tested to validate the model developed. Comparisons are made of the two inverter topologies based on power conversions and loss audits of the test validation hardware.

The current standard electrical downhole machine is the induction machine which is relatively inefficient. Permanent magnet (PM) machines, having higher efficiencies, higher torque densities and smaller volumes, have widely employed in industrial applications to replace conventional machines, but few have been developed for downhole applications due to the high ambient temperatures in deep wells and the low temperature stability of PM materials over time. Today, with the development of variable speed drives and the applications of high temperature magnet materials, it is increasingly interesting for oil and gas industries to develop PM machines for downhole applications. Recently, some PM machines applications have been presented for downhole applications, which are normally addressed on certain specific downhole case. In this thesis the focus has been put on the performance investigation of different PM machines for general downhole cases, in which the machine outer diameter is limited to be small by well size, while the machine axial length may be relatively long. The machine reliability is the most critical requirement while high torque density and high efficiency are also desirable. The purpose is to understand how the special constraints in downhole condition affect the performances of different machines.  First of all, three basic machine concepts, which are the radial, axial and transverse flux machines, are studied in details by analytical method. Their torque density, efficiency, power factor and power capability are investigated with respect to the machine axial length and pole number. The presented critical performance comparisons of the machines provide an indication of machines best suitable with respect to performance and size for downhole applications. Conventional radial flux permanent magnet (RFPM) machines with the PMs on the rotor can provide high torque density and high efficiency. This type of machine has been suggested for several different downhole applications. Flux-switching PM (FSPM) machines, which have the PMs located on the stator and are therefore more reliable, can theoretically also exhibit high torque density and relatively high efficiency. This thesis has put an emphasis on studying this type of machine. Two FSPM machines have been investigated in detail and compared by analytical method, FEM simulation and prototype measuremens. Their operating principle and important design parameters are also presented. A lumped parameter magnetic circuit model for designing a high-torque FSPM machine is newly introduced and the designed machine is verified by FEM simulations. A prototype machine with an outer diameter of 100 mm and an axial length of 200 mm is built in the laboratory and tested at room temperature. Based on that, the machine performance at an ambient temperature of 150°C is also predicted. The results show that the FSPM machine can provide a high torque density with slight compromise of efficiency and power factor. Choosing a proper machine type is significantly dependent on the application specifications. The presented results in this thesis can be used as a reference for selecting the best machine type for a specific downhole case.

Le principal objectif de nos travaux était l’établissement de modèles suffisamment précis pour étudier le comportement des machines électriques en présence d’un défaut de court-circuit entre spires et d’en déduire les signatures pertinentes pour la détection de ce type de défaut. L’autre objectif était de dimensionner des machines électriques à courant de court-circuit d’amplitude limitée pour réduire le risque de propagation du défaut. La première approche de modélisation consiste à effectuer une étude complète en utilisant la méthode d’éléments finis pas à pas dans le temps. Les résultats obtenus par ce modèle "éléments finis" concernant une MSAP et une MAS, saines et aussi en présence de plusieurs défauts "entre spires" de niveaux de sévérité différents, concordent avec ceux obtenus expérimentalement sur deux bancs d’essai. La seconde approche a consisté à mettre au point un modèle "circuits électriques" dont la complexité dépend du type de structure magnétique et du type de bobinage de la machine étudiée. Nous avons proposé deux méthodes de détermination des paramètres : 1- des méthodes numériques (éléments finis) ; 2- l’établissement des nouvelles expressions analytiques. Dans le dernier chapitre, une méthode basée sur la segmentation des aimants sous un pôle qui n’est en fait qu’une démultiplication du nombre de pôles au rotor sans modification du bobinage statorique est proposée est utilisé pour réduire le courant de défaut / The main objective of this research is to establish the sufficiently precise models to study the behavior of electrical machines in the presence of inter-turn short circuit fault and then find the relevant signatures to detect this type of fault. The other objective is to design a limited short-circuit current electrical machines to reduce the risk of fault development. The first modeling approach is a comprehensive study using the time stepping finite element method. The results obtained by this model "finite element" on a MSAP and MAS, healthy and faulty, for different levels of fault severity, are close with those obtained experimentally by two test benches. The second approach is to develop a model circuit electric, whose complexity depends on the type of magnetic structure and the type of machine winding. We have proposed two methods for determining the model parameters: 1 - numerical methods (FEM) which require long time bur very precise; 2 – establish new analytical expressions which is fast but less precise. In the last part, a method based on segmentation of the magnet is presented in order to reduce the short circuit current. The segmented PM motor contains the reduced fault current and can be used in the application which requires high degree of reliability

Práce se zabývá výpočty magnetických a tepelných vlastností servomotoru s permanentními magnety (motor M718 I vyráběný firmou VUES s.r.o. v Brně). Všechny uvedené výpočty jsou založené na numerických metodách konečných prvků a konečných objemů. 2D magnetická analýza motoru byla řešena s pomocí programu FEMM, zatímco pro 3D analýzu byl využit software ANSOFT. Magnetické analýzy umožnily stanovit rozložení magnetického pole v motoru a ve vzduchové mezeře. Ztráty způsobené vířivými proudy byly počítány v závislosti na rozměrech permanentních magnetů a velikosti toku magnetické indukce ve vzduchové mezeře. U 3D modelu v programu ANSOFT byly vypočítány i Joulovy ztráty. Pro daný servomotor byly navrženy dva způsoby chlazení. V prvním případě se jedná o vnitřní chladicí systém. K původnímu modelu motoru byly přidány některé modifikace (otvory v rámu motoru a radiální ventilátor na hřídeli uvnitř rámu motoru). U druhého způsobu chlazení bylo navrženo vnější chlazení. K původnímu rámu byly přidána chladicí žebra a radiální ventilátor na hřídeli vně rámu motoru. Výpočty proudění a tepelná analýza byly provedeny jak pro původní model motoru, tak i pro modifikovaný návrh (vnitřní a vnější chlazení) pomocí software ANSYS Workbench. Teplotní charakteristiky původního motoru byly měřeny různými senzory. Bylo provedeno porovnání experimentálně získaných výsledků s vypočteným teplotním modelem. Práce byla vytvořena v rámci doktorského studijního programu Elektrotechnika a komunikační technologie, obor Silnoproudá elektrotechnika a elektroenergetika. Podstatná část práce vznikla za podpory Centra výzkumu a využití obnovitelných zdrojů energie a výzkumných projektů CZ.1.05/2.1.00/01.0014 and FEKT S-11-9.