The overall objective of this study was to develop an optimised Ultra-High-Performance Concrete (UHPC) matrix based on the modified Andreasen and Andersen optimum particle packing model by using available South African materials. The focus of this study was to determine the optimum combined fibre and superplasticiser content for UHPC by using a response surface design. The UHPC was appropriately designed, produced and tested. Various changes in mechanical properties resulting from different combinations of steel fibre and superplasticiser contents was investigated. The flowability, density and mechanical properties of the designed UHPC were measured and analysed. Both the fibre and superplasticiser content play a significant role in the flowability of the fresh concrete. The addition of fibres significantly improved the strength of the concrete. The results show that the superplasticiser content can be increased if a more workable mix is required without decreasing the strength significantly. The statistical analysis of the response surface methodology confirms that the designed models can be used to navigate the design space defined by the Central Composite Design. The optimum combined fibre and superplasticiser content depend on the required mechanical properties and cost. Using the modified Andreasen and Andersen particle packing model and surface response design methodology, it is possible to efficiently produce a dense Ultra-High-Performance Fibre Reinforced Concrete (UHPFRC) with a relatively low binder amount, low fibre content and good workability. The effect of heat curing on the mechanical properties was investigated. It was concluded that heat curing is not recommended when considering the long-term strength development. The estimated strength development of concrete obtained by using the fib Model Code 2010 (2013) does not incorporate the detrimental effect of high curing temperatures on long-term strength and therefore overestimate the long-term strengths. The strength estimates for both early and long-term ages can be improved by considering this effect in the strength development functions obtained from fib Model Code 2010 (2013). The effect of specimen size on the compressive and flexural tensile strength of UHPFRC members were established. It was found that the specimen size has a significant effect on the measured cube compressive strength. Smaller beam specimens showed higher ductility compared to those of the larger beam specimens. The crack width decreased as the beam’s depth decreased. A lower variability was experienced in the beams with limited depth (< 45 mm). Further testing is required to determine whether a span-to-depth ratio of 10 would yield optimum results. The utilisation of by-products, such as undensified silica fume and fly ash, as cement replacement materials makes UHPFRC sustainable, leading to a reduced life-cycle cost. The calculated Embodied Energy per unit strength (EE/unit strength) and Embodied Carbon per unit strength (EC/unit strength) values for the UHPFRC mixture yield lower values compared to that of the 30 MPa concrete mixture, indicating that UHPFRC can be used to reduce the environmental footprint of the concrete industry. The inverse analysis method used was successful in providing an improved simplified stress-strain response for the UHPFRC. The analysis provided valuable information into the stress-strain, load-deflection and moment-curvature responses of the UHPFRC. Standard material test results were used to theoretically calculate moment-curvature responses and were then compared to the experimental results obtained. The study demonstrated that it is possible to efficiently produce a dense and workable UHPFRC with relatively low binder amount and low fibre content. This can result in more cost-effective UHPFRC, thus improving the practical application thereof. / Dissertation (MEng)--University of Pretoria, 2020. / Civil Engineering / MEng (Structural engineering) / Unrestricted

Concrete is the most widely used construction material worldwide, yet, it presents major sustainability drawbacks due to the CO2 released during the manufacturing of its main constituent, cement. Several approaches are used to improve concrete’s eco-efficiency and reduce the binder intensity index, a metric used to measure the eco-efficiency of concrete, to a value below that of conventional concrete mixtures (i.e., 10 kg/m3.MPa-1 for 25-40 MPa mixtures). Particle Packing Models (PPM) is consequently an approach that can be used to enhance system packing density, reducing cement content while increasing hardened state properties and durability (i.e., reducing porosity). However, packed mixtures normally present issues in the fresh state while their hardened state performance is not fully comprehended. Therefore, this Ph.D. project proposes a new mix-design method called PPM-MP approach to develop eco-efficient mixtures. First, a detailed laboratory investigation was conducted on mixtures developed using the proposed approach in order to understand their fresh and hardened state performance. Concrete samples containing distinct ranges of cement content (320, 250, 200, 150 kg/m3) and slump (180, 90, and 20 +/- 20 mm) were fabricated and a wide range of fresh state tests (pH, temperature, fresh density, air content, slump and rheology over time) and hardened state tests (apparent porosity, surface electrical resistivity, compressive strength, and modulus of elasticity) were performed over time. Then, its performance against the alkali-silica reaction (ASR) induced expansion and deterioration, which is one of the leading and most damaging distress mechanisms issues in durability, was evaluated. In this section of the project, four sustainable concrete mixtures developed with varying cement content (e.g., 325, 250, 200, and 150 kg/m3) were developed and compared to a control mixture containing 420 kg/m3 of cement content. The mixtures were tested over a year under Concrete prism test (CPT) setup, which is the current method used to evaluate concrete ASR and using three different non-boosted test setups (i.e., Wrapped - W, Soaked - S, and Encapsulated - E). Moreover, two distinct types of highly reactive aggregates (e.g., Springhill Greywacke coarse aggregate and Texas Polymictic sand) were selected. Microscopic analysis was used to better understand the impact of ASR on sustainable mixtures, as well as the differences in ASR-damage and crack propagation under different test protocols. The results show the feasibility of producing an eco-efficient mixture in a more efficient manner which may contribute to the Net Zero Concrete targets. The proposed PPM-MP approach improves the sustainability of concrete mixtures and can be used for specific projects requiring 28-day compressive strength ranging from 18 to 45 MPa and slumps (180, 90, and 20 +/- 20 mm).