Spelling suggestions: "subject:"pavement btemperature"" "subject:"pavement bytemperature""
1 |
Evaluation of the Effect of Flowing Water through Embedded Pipe on Rutting Of PavementKadhum, Saly Kadhum Saad 27 April 2011 (has links)
Flexible pavements are layered systems that consist of a sub-grade, sub-base, and the pavement surface layer. Pavement surface layer is a mixture of asphalt binder, coarse, and fine aggregates. The stiffness of asphalt materials is significantly reduced by an increase in temperature. The high heat capacity and the low thermal conductivity of pavement materials result in significant increase in temperature and hence increase in the potential of rutting or permanent deformation in asphalt pavements. Controlling of pavement temperature within a desirable range can be an efficient method to reduce rutting. In this study, the technique of lowering pavement temperature by using a fluid through pipes installed inside the pavement is being investigated. Pavement slabs of hot mix asphalt with and without inserted copper pipe were constructed in the Civil and Environmental Engineering laboratory, and the slabs were tested under high temperature with the Model Mobile Load Simulator 3 (MMLS3). The extraction of heat energy from asphalt pavements was achieved by flowing water through embedded pipe located at 1.5 inches below the surface. This technique resulted in a 10°C decrease in pavement temperature and a reduction of rutting depth from 0.65 inch (significant) to 0.1inch (insignificant). Rut depth and temperature data obtained at different locations along the pavement showed good correlation between surface temperature and rutting depth. The results show that the flowing water through embedded pipes is an effective way to reduce the surface temperature and thus to control rutting depth and prolong the life of pavement.
|
2 |
Performance Analysis and Optimization of a Ground Source Heat Pipe with Carbon Dioxide for Thermal Management of Engineered Pavements and TurfAlhajjaji, Amr Abdurahman 13 July 2022 (has links)
No description available.
|
3 |
The Effect of Pavement Temperature on Frictional Properties of Pavement Surfaces at the Virginia Smart RoadLuo, Yingjian 06 February 2003 (has links)
Wet-pavement friction is a public concern because of its direct relation to highway safety. Both short- and long-term seasonal variations have been observed in friction measurements. These variations have been attributed to different factors, such as traffic, rainfall, and temperature. Since both the tire rubber and the HMA pavement surface are viscoelastic materials, which are physically sensitive to temperature changes, temperature should affect the measured frictional properties. Although several researchers have attempted to explain and quantify the effect of temperature on pavement friction, it remains to be fully understood.
The objective of this research was to quantify the effect of pavement surface temperature on the frictional properties of the pavement-tire interface. To accomplish this, tests conducted on seven different wearing surfaces at the Virginia Smart Road under different climatic conditions were analyzed. Due to the short duration of this study and the low traffic at the facility, only short-term effects of temperature on pavement friction were investigated.
To accomplish the predefined objective, skid test data from both ribbed and smooth tires were collected over two and a half years (from January 2000 to August 2002) and then analyzed. Six sets of tests were conducted under different environmental conditions. The pavement and air temperatures during each test were obtained using thermocouples located directly under the wearing course (38mm below the surface) and close to the pavement surface, respectively. Regression analyses were conducted to determine the effect of pavement temperature on the measured skid number at different speeds, as well as on friction model parameters.
The main conclusion of this investigation is that pavement temperature has a significant effect on pavement frictional measurements and on the sensitivity of the measurements to the test speed. Both the skid number at zero speed (SN0) and the percent normalized gradient (PNG) tend to decrease with increased pavement temperature. This results in the pavement temperature on the measured skid number being dependent on the testing speed. For the standard wearing surface mixes studied at low speed (lower than 32 km/hr), pavement friction tends to decrease with increased pavement temperature. At high speed, the effect is reverted and pavement friction tends to increase with increased pavement temperature. Temperature-dependent friction versus speed models were established for one of the mixes studied. These models can be used to define temperature correction factors. / Master of Science
|
4 |
Improvements to a Transport Model of Asphalt Binder Oxidation in Pavements: Pavement Temperature Modeling, Oxygen Diffusivity in Asphalt Binders and Mastics, and Pavement Air Void CharacterizationHan, Rongbin 2011 May 1900 (has links)
Although evidence is mounting that asphalt binder oxidizes in pavements, and that oxidation and subsequent hardening of asphalt binder has a profound effect on pavement durability, important implementation issues remain to be better understood. Quantitative assessment of asphalt binder oxidation for a given pavement is a very important, but complex issue.
In this dissertation, a fundamentals-based oxygen transport and reaction model was developed to assess quantitative asphalt binder oxidation in pavements. In this model, oxygen transport and reaction were described mathematically as two interlinked steps: 1) diffusion and/or flow of oxygen from the atmosphere above the pavement into the interconnected air voids in the pavement; and 2) diffusion of oxygen from those air voids into the adjoining asphalt-aggregate matrix where it reacts with the asphalt binder.
Because such a model calculation depends extensively on accurately representing pavement temperature, understanding oxygen diffusivity in asphalt binders and mastics, and characterizing air voids in pavements, these key model elements were studied in turn. Hourly pavement temperatures were calculated with an improved one-dimensional heat transfer model, coupled with methods to obtain model-required climate data from available databases and optimization of site-specific pavement parameters nationwide; oxygen diffusivity in binders was determined based on laboratory oxidation experiments in binder films of known reaction kinetics by comparing the oxidation rates at the binder surface and at a solid-binder interface at the film depth. The effect of aggregate filler on oxygen diffusivity also was quantified, and air voids in pavements were characterized using X-ray computed tomography (X-ray CT) and image processing techniques. From these imaging techniques, three pavement air void properties, radius of each air void (r), number of air voids (N), and average shell distance between two air voids (rNFB) were obtained to use as model inputs in the asphalt binder oxidation model.
Then, by incorporating these model element improvements into the oxygen transport and reaction model, asphalt binder oxidation rates for a number of Texas and Minnesota pavements were calculated. In parallel, field oxidation rates were measured for these corresponding pavement sites and compared to the model calculations. In general, there was a close match between the model calculations and field measurements, suggesting that the model captures the most critical elements that affect asphalt binder oxidation in pavements.
This model will be used to estimate the rate of asphalt binder oxidation in pavements as a first step to predicting pavement performance, and ultimately, to improve pavement design protocols and pavement maintenance scheduling.
|
5 |
Toward an Improved Model of Asphalt Binder Oxidation in PavementsPrapaitrakul, Nikornpon 2009 December 1900 (has links)
Asphalt binder oxidation in pavements has been proven to be an ongoing process
throughout a pavement's service life. Understanding the nature of the oxidation process
is a critical step toward better pavement design to achieve greater pavement durability.
The main component in asphalt binder oxidation in pavements is binder oxidative
hardening. As the aromatic compounds in asphalt binders are oxidized, more polar
carbonyl compounds are created, which results in stronger associations between asphalt
components and eventually leads to an increase in asphalt elastic modulus and viscosity.
Consequently, the performance of pavements is affected directly by asphalt binder
hardening.
Also, low levels of accessible air voids in pavements potentially relate to binder
oxidation according to a recent research study. When the pavements have sufficiently
high accessible air voids (4 percent or greater), the oxidation rate is largely determined
by the temperature in the pavement. On the other hand, when the percentage of
accessible air voids in the pavement is considerably lower (2 percent or less), the
hardening rate of binders in pavements is reduced significantly.
Field evidence is mounting that asphalt binder oxidization in pavements produces
a binder that is more susceptible to thermal and fatigue cracking. While the
fundamentals of this oxidation process are fairly well known, predicting quantitatively
the rate of oxidation as a function of depth in the pavement, is not straightforward. A
thermal and oxygen transport model, coupled with binder reaction kinetics, provides the basis for such calculations. A one-dimensional thermal transport model, coupled with
site-specific model parameters and recent improvements in the availability of required
input climate data, enables calculation of pavement temperatures throughout the year,
which then is used in an asphalt binder oxidation and transport model to calculate binder
properties in the pavement over time. Calculated binder property changes with depth and
time are compared to measurements of binder oxidation in the field.
The work in this study is aimed at understanding the oxidation kinetics of asphalt
binders in pavements, determining the impact of accessible air void levels on asphalt
hardening, and ultimately developing an improved model of asphalt binder oxidation in
pavements.
|
6 |
Moisture Content Determination and Temperature Profile Modeling of Flexible Pavement StructuresDiefenderfer, Brian Keith 03 May 2002 (has links)
A majority of the primary roadways in the United States are constructed using hot-mix asphalt (HMA) placed over a granular base material. The strength of this pavement system is strongly influenced by the local environmental conditions. Excessive moisture in a granular base layer can cause that layer to lose its structural contribution by reducing the area over which loading may be distributed. Excessive moisture and fine particles can be transported by hydrostatic pressure to the surface layers, thus reducing the strength of the overlying HMA by contamination. Moisture in the surface HMA layers can cause deterioration through stripping and raveling. In addition, as HMA is a viscoelastic material, it behaves more as a viscous fluid at high temperatures and as an elastic solid at low temperatures. Between these two temperature extremes, a combination of these properties is evident. Thus, understanding the environmental effects on flexible pavements allows better prediction of pavement performance and behavior under different environmental conditions.
As part of the ongoing pavement research at the Virginia Smart Road, instrumentation was embedded during construction to monitor pavement response to loading and environment; moisture content of the granular base layers and temperature of the HMA layers were among the responses monitored. The Virginia Smart Road, constructed in Blacksburg, Virginia, is a pavement test facility is approximately 2.5km in length, of which 1.3km is flexible pavement that is divided into 12 sections of approximately 100m each. Each flexible pavement section is comprised of a multi-layer pavement system and possesses a unique structural configuration. The moisture content of aggregate subbase layers was measured utilizing two types of Time-Domain Reflectometry (TDR) probes that differed in their mode of operation. The temperature profile of the pavement was measured using thermocouples.
Data for the moisture content determination was collected and results from two probe types were evaluated. In addition, the differences in the moisture content within the aggregate subbase layer due to pavement structural configuration and presence of a moisture barrier were investigated. It was shown that the two TDR probe types gave similar results following a calibration procedure. In addition to effects due to pavement structure and subgrade type, the presence of a moisture barrier appeared to reduce the variability in the moisture content caused by precipitation. Temperature profile data was collected on a continuous basis for the purpose of developing a pavement temperature prediction model. A linear relationship was observed between the temperature given by a thermocouple near the ground surface and the pavement temperature at various depths. Following this, multiple-linear regression models were developed to predict the daily maximum or minimum pavement temperature in the HMA layers regardless of binder type or nominal maximum particle size. In addition, the measured ambient temperature and calculated received daily solar radiation were incorporated into an additional set of models to predict daily pavement temperatures at any location. The predicted temperatures from all developed models were found to be in agreement with in-situ measured temperatures. / Ph. D.
|
7 |
Comparison of Winter Temperature Profiles in Asphalt and Concrete PavementsDye, Jeremy Brooks 12 August 2010 (has links) (PDF)
Because winter maintenance is so costly, Utah Department of Transportation (UDOT) personnel asked researchers at Brigham Young University to determine whether asphalt or concrete pavements require more winter maintenance. Differing thermal properties suggest that, for the same environmental conditions, asphalt and concrete pavements will have different temperature profiles. Climatological data from 22 environmental sensor stations (ESSs) near asphalt roads and nine ESSs near concrete roads were used to 1) determine which pavement type has higher surface temperatures in winter and 2) compare the subsurface temperatures under asphalt and concrete pavements to determine the pavement type below which more freeze-thaw cycles of the underlying soil occur. Twelve continuous months of climatological data, primarily from the 2009 calendar year, were acquired from the road weather information system operated by UDOT, and erroneous data were removed from the data set. To predict pavement surface temperature, a multiple linear regression was performed with input parameters of pavement type, time period, and air temperature. Similarly, a multiple linear regression was performed to predict the number of subsurface freeze-thaw cycles, based on month, latitude, elevation, and pavement type. A finite-difference model was created to model surface temperatures of asphalt and concrete pavements based on air temperature and incoming radiation. The statistical analysis predicting pavement surface temperatures showed that, for near-freezing conditions, asphalt is better in the afternoon, and concrete is better for other times of the day, but that neither pavement type is better, on average. Asphalt and concrete are equally likely to collect snow or ice on their surfaces, and both pavements are expected to require equal amounts of winter maintenance, on average. Finite-difference analysis results confirmed that, for times of low incident radiation (night), concrete reaches higher temperatures than asphalt, and for times of high incident radiation (day), asphalt reaches higher temperatures than concrete. The regression equation predicting the number of subsurface freeze-thaw cycles provided estimates that did not correlate well with measured values. Consequently, an entirely different analysis must be conducted with different input variables. Data that were not available for this research but are likely necessary in estimating the number of freeze-thaw cycles under the pavement include pavement layer thicknesses, layer types, and layer moisture contents.
|
8 |
Evaluation of Rigid Pavement Rehabilitation Methods Using an Unbonded Concrete OverlayAmbrosino, Joel D. 24 July 2007 (has links)
No description available.
|
9 |
Metodología de determinación del módulo de elasticidad de la carpeta asfáltica considerando la congestión vehicular en intersecciones urbanas / Methodology for determining the modulus of elasticity of the asphalt layer considering vehicular congestion in urban intersectionsMarceliano Alcantara, Luis Alberto, Sandoval Moreno, Lucero Francia 09 December 2020 (has links)
En la actualidad la congestión vehicular es un problema de muchas ciudades del mundo. Este problema no solo se ha convertido en un sinónimo de estrés y ansiedad para algunas personas, sino que también se ha convertido en un reto para los expertos en Pavimentos. La congestión no solo implica un alto incremento de carga sobre las vías, sino que también implica cambios en las propiedades mecánicas del pavimento. La velocidad vehicular, temperatura y la sobrecarga del pavimento dentro del tráfico son componentes que sin duda se deben ver reflejados en una metodología, ya que estos están alterando la vida útil de las vías. La presente investigación propone una metodología empírica de determinación del módulo de elasticidad en una carpeta asfáltica. Dentro de esta nueva propuesta se incluyen conceptos que no se han tomado en cuenta: la influencia de la congestión. El experimento de comparación se realizó entre una vía a temperatura de congestión y sin congestión, 35°C y 25 °C respectivamente. Este método fue verificado mediante el uso de fórmulas y ensayos de módulo de elasticidad. / Currently, traffic congestion is a problem in many cities around the world. This problem has not only become synonymous with stress and anxiety for some people, but it has also become a challenge for flooring experts. Congestion not only implies a high increase in load on the roads, but also implies changes in the mechanical properties of the pavement. Vehicle speed, temperature and pavement overload within traffic are components that should undoubtedly be reflected in a methodology, since these are altering the useful life of the roads. This research proposes an empirical methodology for determining the modulus of elasticity in an asphalt mat. This new proposal includes concepts that have not been considered: the influence of congestion. The comparison experiment was carried out between a pathway at a congestion temperature and without congestion, 35 ° C and 25 ° C, respectively. This method was verified by using formulas and modulus of elasticity tests. / Trabajo de investigación
|
Page generated in 0.099 seconds