Photonic Crystal structures have been heralded as a disruptive technology for the miniaturization of opto-electronic devices, offering as they do the possibility of guiding and manipulating light in sub-micron scale waveguides. Applications of photonic crystal guiding - the ability to send light around sharp bends or compactly split signals into two or more channels have attracted a great deal of attention. Other effects of this waveguiding mechanism have become apparent, and attracted much interest - the novel dispersion surfaces of photonic crystal structures allow the possibility of “slow light” in a dielectric medium, which as well as the possibility of compact optical delay lines may allow enhanced light-matter interaction, and hence miniaturisation of active optical devices. I also consider a third, more traditional type of photonic crystal, in the form of a grating for surface coupling. In this thesis, I address many of the aspects of passive photonic crystals, from the underlying theory through applied device modelling, fabrication concerns and experimental results and analysis. Further, for the devices studied, I consider both the relative merits of the photonic crystal approach and of my work compared to that of others in the field. Thus, the complete spectrum of photonic crystal devices is covered. With regard to specific results, the highlights of the work contained in this thesis are as follows: Realisation of surface grating couplers in a novel material system demonstrating some of the highest reported fibre coupling efficiencies. Development of a short “injecting” taper for coupling into photonic crystal devices. Optimisation and experimental validation of photonic crystal routing elements (Y-splitter and bend). Exploration of interfaces and coupling for “slow light” photonic crystals.

Photonic bandgap structures have provided promising platform for miniaturization of modern integrated optical devices. In this thesis, a photonic crystal based ring resonator (PCRR) is proposed and optimized to exhibit high quality factor. Also, force sensing application of the optimized PC ring resonator and Dense Wavelength Division Multiplexing (DWDM) application of the PCRR are discussed. Finally fabrication and characterization of the PCRR is presented. A photonic crystal ring resonator is designed in a hexagonal lattice of air holes on a silicon slab. A novel approach is used to optimize PCRR to achieve high quality factor. The numerical analysis of the optimized photonic crystal ring resonator is presented in detail. For all electromagnetic computations Finite Difference Time Domain (FDTD) method is used. The improvement in Q factor is explained by using the physical phenomenon, multipole cancellation of the radiation held of the PCRR cavity. The corresponding mathematical frame work has been included. The forced cancellation of lower order radiation components are verified by plotting far held radiation pattern of the PCRR cavity. Then, the force sensing application of the optimized PCRR is presented. A high sensitive force sensor based on photonic crystal ring resonator integrated with silicon micro cantilever is presented. The design and modelling of the device, including the mechanics of the cantilever, FEM (Finite Element Method) analysis of the cantilever beam with PC and without PC integrated on it. The force sensing characteristics are presented for forces in the range of 0 to 1 N. For forces which are in the range of few tens of N, a force sensor with bilayer cantilever is considered. PC ring resonator on the bilayer of 220nm thick silicon and 600nm thick SiO2 plays the role of sensing element. Force sensing characteristics of the bilayer cantilever for forces in the range of 0 to 10 N are presented. Fabrication and characterization of PCRR is also carried out. This experimental work is done mainly to understand practical issues in study of photonic crystal ring resonators. It is proved that Q factor of PCRR can be signi cantly improved by varying the PCRR parameters by the proposed method. Dense Wavelength Division Multiplexing (DWDM) application of PC ring resonator is included. A novel 4-channel PC based demultiplexer is proposed and optimized in order to tolerate the fabrication errors and exhibit optimal cross talk, coupling efficiency between resonator and various channels of the device. Since the intention of this design is, to achieve the device performance that is independent of the unavoidable fabrication errors, the tolerance studies are made on the performance of the device towards the fabrication errors in the dimension of various related parameters. In conclusion we summarize major results, applications including computations and practical measurements of this work and suggest future work that may be carried out later.