Thesis (M.S.)--Rochester Institute of Technology, 2009. / Typescript. Includes bibliographical references (leaves 52-54).

Thesis (M.S.)--Rochester Institute of Technology, 1995. / Typescript. Bibliography: leaves 67-68.

No description available.

Kwok, Yiu-fai. / Thesis (M.Phil.)--Chinese University of Hong Kong, 2000. / Includes bibliographical references (leaves 87-89). / Abstracts in English and Chinese. / ABSTRACT --- p.I / ACKNOWLEDGMENTS --- p.II / TABLE OF CONTENT --- p.III / LIST OF FIGURES --- p.V / Chapter 1 --- INTRODUCTION --- p.1 / Chapter 1.1 --- Background --- p.1 / Chapter 1.2 --- Motivation of this project --- p.1 / Chapter 1.3 --- Organization --- p.2 / Chapter 2 --- LITERATURE SURVEY --- p.3 / Chapter 2.1 --- Ionic Conducting Polymer Film (ICPF) --- p.3 / Chapter 2.2 --- Electroactive Polymer (EAP) --- p.4 / Chapter 2.3 --- Micro Active Guide Wire Catheter System --- p.5 / Chapter 2.4 --- Space Application - Dust Wiper --- p.6 / Chapter 2.5 --- Micro gripper --- p.8 / Chapter 2.6 --- Summary of literature survey --- p.14 / Chapter 3 --- METAL-POLYMER COMPOSITIONS --- p.15 / Chapter 3.1 --- Introduction --- p.15 / Chapter 3.2 --- Perfluorosulfonic acid polymer (Nafion) --- p.15 / Chapter 3.3 --- Working principle of ICPF --- p.19 / Chapter 3.4 --- Different types of composition --- p.21 / Chapter 3.4.1 --- Chromium-Gold-polymer composite --- p.23 / Chapter 3.4.2 --- Platinum-Gold-polymer composite --- p.25 / Chapter 3.4.3 --- Silver-polymer composite --- p.27 / Chapter 3.4.4 --- Silver/Copper-gold polymer composite --- p.27 / Chapter 3.4.5 --- Gold-polymer composite --- p.28 / Chapter 4 --- ICPF FABRICATION --- p.30 / Chapter 4.1 --- Introduction --- p.30 / Chapter 4.2 --- ICPF fabrication process --- p.31 / Chapter 4.3 --- Surface pre-treatment --- p.33 / Chapter 4.4 --- Gold thin film deposition (Evaporation) --- p.34 / Chapter 4.4.1. --- Filament evaporation --- p.35 / Chapter 4.4.2 --- Electronic-beam evaporation --- p.39 / Chapter 4.4.3 --- Structural analysis of evaporation --- p.40 / Chapter 4.5 --- Chemical electroplating --- p.42 / Chapter 4.5.1. --- Deposition rate calibration --- p.44 / Chapter 5 --- DESIGN AND PACKAGE --- p.46 / Chapter 6 --- LASER MICROMACHINING --- p.49 / Chapter 6.1 --- Introduction to Laser micromachining --- p.49 / Chapter 6.2 --- C02 laser --- p.50 / Chapter 6.3 --- Nd:YAG Laser --- p.51 / Chapter 6.4 --- Laser micromachining of ICPF actuator --- p.52 / Chapter 7 --- EXPERIMENTAL RESULTS AND ANALYSIS --- p.61 / Chapter 7.1 --- Introduction --- p.61 / Chapter 7.2 --- Measurement setup --- p.62 / Chapter 7.3 --- Width test --- p.68 / Chapter 7.4 --- Length test --- p.73 / Chapter 7.5 --- Voltage test --- p.76 / Chapter 8 --- MICRO GRIPPER ACTUATION --- p.79 / Chapter 8.1 --- Development of micro gripper --- p.79 / Chapter 8.2 --- Micro gripper --- p.80 / Chapter 9 --- CONCLUSION --- p.82 / Chapter 10 --- APPENDIX --- p.83 / Chapter 10.1 --- Procedures in using E-beam evaporator --- p.83 / Chapter 10.2 --- Procedures in using Thermo couple evaporator --- p.85 / Chapter 11 --- REFERENCE --- p.87

No description available.

No description available.

This creative project has investigated the engineering principles relative to the design and construction of a blown tubular film take-off system. The study has also made a careful analysis of the equipment necessary to construct a blown tubular film extrusion line.In addition, the creative project has discussed alternate methods of producing polyolefin filets, it has suggested possible solutions for troubleshooting which can provide valuable assistance in the successful production of quality blown tubular film.

Thesis (M.S.)--Rochester Institute of Technology, 1990. / Includes bibliographical references (leaves 52-54).

Thesis (M.S.)--California Polytechnic State University, 2009. / Mode of access: Internet. Title from PDF title page; viewed on March 25, 2009. Major professor: J. Wyatt Brown. "Presented to the faculty of California Polytechnic State University, San Luis Obispo." "In partial fulfillment of the requirements for the degree [of] Master of Science in Agriculture with specialization in Crop Science." "March, 2009." Includes bibliographical references (p. 30-32). Also available on microfiche.

Thesis (M.S.)--Rochester Institute of Technology, 1994. / Typescript. Includes bibliographical references (leaves 147-153).