Asphalt mixtures or asphalt concrete are used to pave about 93% of about 2.6 million miles paved roads and highways in the US. Asphalt concrete is a composite of aggregates and asphalt binder; asphalt binder works as a glue to bind the aggregate particles. The mechanical response of the asphalt binder is dependent on the time/rate of loading, temperature and age. An asphalt concrete mixture inherits most of these characteristics from the asphalt binder. Also the asphalt binder plays a critical role in providing the asphalt concrete the ability to resist tensile stresses and relaxing thermally induced stresses that can lead to fatigue and low temperature cracking, respectively. Hence, it is very important (but not sufficient) to ensure that asphalt binders used in the production of asphalt concrete are inherently resistant to cracking, rutting and other distresses that a pavement may undergo. Current binder specification (AASHTO M-320) to evaluate its fatigue cracking is based on the stiffness of the binder and not on its tensile strength. Also, measurements following current specifications are made on test specimens subjected to a uniaxial mode of loading that does not produce the same stress state in the binder as in the case of asphalt concrete. Another challenge in being able to produce binders with inherently superior performing characteristics is the fact that the asphalt binders produced in a refinery do not have a consistent chemical composition. The chemical composition of asphalt binder depends on the source and refining process of crude oil. There is a need to better quantify the tensile strength of asphalt binder and understand the relationship between the chemical composition of asphalt binders and its mechanical properties. The knowledge from this study can be used to engineer asphalt binders that have superior performance characteristics. The objective of this research was to quantify the tensile strength of asphalt binder, develop a metric for the tensile strength and identify the relationship between chemical composition and mechanical properties of asphalt binder. Laboratory tests were performed on binders of different grades using a poker chip geometry to simulate confined state by varying the film thickness, rate of loading and modes of loading. The chemical properties of asphalt binder were studied based on SARA fractionation. The findings from this research showed that the modified correspondence principles can unify and explain the rate and mode dependency of asphalt binder. This study also quantified the relationship between chemical composition, and rheological and mechanical properties of asphalt binder. Finally, a composite model was developed based on the individual properties of chemical fractions which could predict the dynamic modulus of the asphaltenes doped and resins doped binder. / text

Asphalt mixtures are complex composites that comprise aggregate, asphalt binder, and air. Several research studies have shown that the mechanical behavior of the asphalt mixture is strongly influenced by the matrix, i.e. the asphalt binder. Therefore, accurate constitutive models for the asphalt binders are critical to ensure accurate performance predictions at a material and structural level. However, researchers who use computational methods to model the micromechanics of asphalt mixtures typically assume that (i) asphalt binders behave linearly in shear, and (ii) either bulk modulus or Poisson’s ratio of asphalt binders is not time dependent. This research develops an approach to measure and model the shear and bulk behavior of asphalt binders at intermediate temperatures. First, this research presents the findings from a systematic investigation into the nature of the linear and nonlinear response of asphalt binders subjected to shear using a Dynamic Shear Rheometer (DSR). The DSR test results showed that under certain conditions a compressive normal force was generated in an axially constrained specimen subjected to cyclic torque histories. This normal force could not be solely attributed to the Poynting effect and was also related to the tendency of the asphalt binder to dilate when subjected to shear loads. The generated normal force changed the state of stress and interacted with the shear behavior of asphalt binder. This effect was considered to be an “interaction nonlinearity” or “three dimensional effect”. A constitutive model was identified to accommodate this effect. The model was successfully validated for several different loading histories. Finally, this study investigated the time-dependence of the bulk modulus of asphalt binders. To this end, poker-chip geometries with high aspect ratios were used. The boundary value problem for the poker-chip geometry under step displacement loading was solved to determine the bulk modulus and Poisson’s ratio of asphalt binders as a function of time. The findings from this research not only improve the understanding of asphaltic materials behavior, but also provide tools required to accurately predict pavement performance. / text