In this study, the effect of compatibilizers on the gas separation performance of polycarbonate (PC) membranes was investigated. Membranes were prepared by solvent evaporation method. They were characterized by single gas permeability measurements of O2, N2, H2 and CO2 as well as scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared spectrometry (FTIR). Membranes containing 0.5 to 10 w% p-nitroaniline (pNA) were prepared to study the effect of compatibilizer concentration on the membrane performance. Permeabilities of all gases decreased but selectivities increased with pNA concentration. The membranes with 5 w% pNA showed a selectivity of 114.5 for H2 over N2, 53.9 for CO2 over N2 and 13.4 for O2 over N2 at room temperature, whereas, the H2/N2, CO2/N2 and O2/N2 selectivities for pure PC membranes were 43.5, 20.6 and 5.6, respectively. The N2 permeabilities through pure PC membrane and 5 w% pNA/PC membrane were 0.265 and 0.064 barrer, respectively. The glass transition temperature of the membranes decreased with increasing pNA concentration. FTIR spectra showed that the peaks assigned to nitro and amine groups of pNA shifted and/or broadened. The DSC and FTIR results suggested an interaction between PC and pNA. The effect of type of compatibilizer was also studied. The compatibilizers were 4-amino 3-nitro phenol (ANP), Catechol and 2-hydroxy 5-methyl aniline (HMA). Similar to membranes prepared with pNA, membranes prepared with these compatibilizers had a lower permeability and glass transition temperature but higher selectivity than pure PC membranes. Their FTIR spectra were also indicated a possible interaction between PC and compatibilizer. In conclusion, PC/compatibilizer blend membranes for successful gas separation were prepared. Low molecular weight compounds with multifunctional groups were found to effect membrane properties at low concentration range, 0.5-5 w%.

<p>Microbiological contamination from bacteria such as <em>Escherichia coli</em> and Salmonella is one of the main reasons for waterborne illness. Real time and accurate monitoring of water is needed in order to alleviate this human health concern. Performing multiple and parallel analysis of biomarkers such as DNA and mRNA that targets different regions of pathogen functionality provides a complete picture of its presence and viability in the shortest possible time. These biomarkers are present inside the cell and need to be extracted for analysis and detection. Hence, lysis of these pathogenic bacteria is an important part in the sample preparation for rapid detection. In addition, collecting a small amount of bacteria present in a large volume of sample and concentrating them before lysing is important as it facilitates the downstream assay. Various techniques, categorized as mechanical, chemical, thermal and electrical, have been used for lysing cells. In the electrical method, cells are lysed by exposure to an external electric field. The advantage of this method, in contrast to other methods, is that it allows lysis without the introduction of any chemical and biological reagents and permits rapid recovery of intercellular organelles. Despite the advantages, issues such as high voltage requirement, bubble generation and Joule heating are associated with the electrical method.</p> <p>To alleviate the issues associated with electrical lysis, a new design and associated fabrication process for a microfluidic cell lysis device is described in this thesis. The device consists of a nanoporous polycarbonate (PCTE) membrane sandwiched between two PDMS microchannels with electrodes embedded at the reservoirs of the microchannels. Microcontact printing is used to attach this PCTE membrane with PDMS.</p> <p>By using this PCTE membrane, it was possible to intensify the electric field at the interface of two channels while maintaining it low in the other sections of the device. Furthermore, the device also allowed electrophoretic trapping of cells before lysis at a lower applied potential. For instance, it could trap bacteria such as <em>E. coli</em> from a continuous flow into the intersection between two channels for lower electric field (308 V/cm) and lyse the cell when electric field was increased more than 1000 V/cm into that section.</p> <p>Application of lower DC voltage with pressure driven flow alleviated adverse effect from Joule heating. Moreover, gas evolution and bubble generation was not observed during the operation of this device.</p> <p>Accumulation and lysis of bacteria were studied under a fluorescence microscope and quantified by using intensity measurement. To observe the accumulation and lysis, LIVE/DEAD BacLight Bacterial Viability Kit consisting of two separate components of SYTO 9 and propidium iodide (PI) into the cell suspension in addition to GFP expressed <em>E. coli</em> were used. Finally, plate counting was done to determine the efficiency of the device and it was observed that the device could lyse 90% of bacteria for an operation voltage of 300V within 3 min.</p> <p>In conclusion, a robust, reliable and flexible microfluidic cell lysis device was proposed and analyzed which is useful for sample pretreatment in a Micro Total Analysis System.</p> / Master of Applied Science (MASc)