The full capacity of the existing transmission lines is often underutilized due to the system stability requirements. Controllable network devices represent the effective means of improving the system stability, and their deployment allows better use of the existing transmission facilities and can help to avoid construction of new lines. This dissertation addresses system analysis and modeling of controllable network devices. Transient angle stability is one of the major requirements limiting transfer capability of the power transmission systems. The theoretical concepts of transient angle controllability using controllable network devices are considered in this dissertation. The main results are derived for a general transmission network structure and applied to series and shunt compensators as well as braking resistors. The proposed approach allows to quantify controllability and to relate it to the control device size, type and location in the transmission network. Transient stability controllers are needed to maximize the device effect on the transient angle stability enhancement. The transient stability controller functional structure is discussed and the design requirements for each component are specified. The examples of controller designs are presented. Emerging technologies such as Thyristor-Controlled Series Compensators and Synchronous Voltage Sources offer superior control capabilities and performance characteristics as compared to conventional compensators. Unlike conventional compensators, the new controllable network devices are very complex dynamical systems and require more comprehensive modeling for time-domain studies and controller designs. Detailed models of a Thyristor-Controlled Series Compensator and a Synchronous Voltage Source for powerflow, transient stability, and electro-magnetic transient studies are presented. Finally, a detailed planning study for increasing transfer capability of the Montana transmission system using controlled series compensation is presented. A variety of design and performance requirements is considered in this study, which makes it a useful reference for similar planning projects. / Graduation date: 1996

Sherman M. Chan, Michael Athans. / Bibliography: leaf 9. / Caption title. "August 15, 1981." / Supported by the U.S. Department of Energy, Division of Electric Energy Systems, under Contract DE-AC01-78RA03395

published_or_final_version / Electrical Engineering / Master / Master of Philosophy

This thesis aims to verify the use of quantitative feedback theory (QFT) as a viable tool for designing power system stabilisers (PSS) for a single machine infinite bus system. The result of the QFT design is verified by simulation of the linear and nonlinear models representing the power system, and also by experimental procedures carried out in a laboratory. QFT falls into the classical control category, and is a frequency domain design method. It is an alternative to other design methods such as root locus and Hoo . The QFT design procedure can be extended to a multimachine system and QFT designs of MIMO systems has gained impetus. From theory, through simulation, and to the final laboratory testing on a single machine, infinite bus system, it will be shown that the application of QFT to robust PSS design does indeed work. QFT is a design method that allows the designer to choose a set of realistic operating points and to produce a design that include those points. Other methods allow the designer to produce a design for single operating point, and one has no idea how the design performs at the other operating points. / Thesis (M.Sc.Eng.)-University of Natal, Durban, 2003.

This thesis investigates the design of damping controllers to alleviate the problem of low frequency electro-mechanical oscillations in power systems. The operating point and network parameters of power systems are continually changing, resulting in changes in system dynamics. The conventional controller design methodology has therefore come under increasing scrutiny for its lack of considerations for robustness. The thesis first outlines the conventional design of a power system stabilizer (PSS) and then applies two robust techniques (Hoo and Quantitative Feedback Theory, QFT) to the design problem. The single machine infinite bus (SMIB) model is used to illustrate the procedure for all three design techniques. The final design is undertaken to illustrate the more important problem of robust multi-machine PSS design using QFT. The design requires linearised models of the multi-machine system. A brief discussion is given on how these can be obtained. An introduction to decentralized control design in QFT is included to support the multi-machine design. Chapter three proceeds through the design steps required to generate a conventional PSS. The technique is shown to be simple for a given set of operating conditions. The controller is shown to be adequately robust over the given set of operating conditions albeit not by design. Chapter four introduces a design technique that directly addresses robustness issues during the controller design. For a restricted range of operating conditions the designed controller demonstrates the desired robustness and performance characteristics. The inherent difficulties with Hoo in PSS design become more apparent as the operating range is extended. Chapter five introduces the second robust controller design technique. QFT is shown to be more adept at dealing with increased operating ranges and changing specifications in the single-machine infinite-bus case. The controller is easy to generate and performs well over the entire range of operating conditions. QFT is also applied to the controller design for a four-machine study system. The design is a marginally more complex than in the single machine case but is still easily accomplished. This thesis confirms previous attempts at solving the design problem using the methods outlined above. The performance of all controllers is assessed for small and large disturbances using non-linear time domain simulations with models developed using PSCAD/EMTDC and MATLAB. / Thesis (M.Sc.)-University of Natal,Durban, 2002.

Poorly damped oscillations that occur between the generators in large interconnected power systems often limit the amount of power that can be transmitted through a transmission corridor and are a threat to secure system operation. Coordinated insertion and removal of capacitors in series with a transmission line is one of the approaches that has been known for many years to be capable of enhancing the damping of power system oscillations. Unfortunately however, this approach historically relied on the operation of mechanical circuit breakers which were too slow and unreliable for the high-speed and repetitive operation that such an application demands. Recently-emerged, high-speed power-electronic-based switching devices are finding increasing use in modem power systems in the so-called Flexible AC Transmission Systems (F ACTS) concept. One particular FACTS impedance controller, namely the inverter-based series compensator, can rapidly alter the magnitude of capacitive compensating reactance in series with the line to make it practically feasible to enhance the damping of power system oscillations via dynamically-controlled series compensation. This thesis identifies, in the literature, an insightful approach to the design of an idealised controllable series compensator (CSC) damping scheme; such an approach has been considered in the analyses of the thesis. Three mathematical models of a single-machine infinite bus (SMIB) system are developed and are subsequently used in the initial design and analysis of a CSC damping controller carried out in the thesis. The simple SMIB system case study is used to identify and investigate the factors that have a significant impact on the performance of a CSC damping controller before studying the more complex issue of inter-area mode damping using a CSC. This thesis successfully confirms the results of a previous analytical study in which an idealised representation of the CSC was used, and extends the scope of that previous study by also considering a detailed representation of one particular type of CSC: the inverter-based series compensator. The two key findings of this extended investigation are that the inverter-based form of controllable series compensator can successfully be used to damp power oscillations and that, where the damping of oscillations is the particular focus of study, an idealised representation of the inverterbased CSC is suitable for the analyses. In the case of the inter-area mode damping problem, the selection of an appropriate input signal to the CSC damping controller is a key issue, since the oscillations that are to be damped involve a number of participating generators. This thesis examines the suitability of a few candidate input signals that have been proposed in the literature using the conceptually simpler SMIB system analytical models that have been developed. Finally, the thesis applies the understanding of CSC damping controller design gained from the SMIB study to the problem of inter-area mode damping on a four-generator study system. Time-domain simulation results are presented to demonstrate the impact of the controlled inverter-based series compensator on the damping of the inter-area mode of this system. / Thesis (M.Sc.Eng.)-University of Natal, Durban, 2000.

Voltage unbalance performance of a power line depends on a few parameters that are not necessarily constant at any given instance. The random nature of a power system raises questions around the ability of a system planner to allocate equitable share of the power quality parameters, like voltage unbalance, at design stage. Even a more interesting question is whether applying current methods will guarantee that emissions will be under the set limits. The presence of single or dual phase feeders on such a line will result in a more dynamic voltage unbalance. The first part of this research is a study on deterministic method of voltage unbalance allocation presented by the IEC. The IEC 61000-13-3 report is a comprehensive guideline and the best place to start when looking to develop an emissions standard for voltage unbalance. This dissertation presents a method that can be used to set planning levels for unbalance emission at various voltage levels in order to avoid high voltage unbalance at the end user. The method depends on the agreed power of the customer, the power of the unbalanced load, and the system characteristics. The method works well for short feeders with roughly the same negative sequence impedance and equal short circuit levels. In South Africa, however, there are radial feeders that span over 100km. Hence on such a feeder, there can be ratios of 1:10 between sending end and the last customer on the line. Preliminary research revealed that IEC 61000-6-3, a report on allocation of harmonics, has a method applicable to long feeders. This method was investigated extensively and applied to voltage unbalance allocation. At the core of the method is the assumption that feeders have an even distribution of load. To illustrate the application of this method an example is given. The second part of the study explores a stochastic method of voltage unbalance allocation. In this study the possibility of random connection is considered. A Monte Carlo study is presented. The impact of various parameters are analysed and the findings reveal that phase allocation has the most influence on emission. The results show that the method of random connection of loads can be applied in special conditions only i.e. were sizes of loads do not differ greatly and the number of required connections are low. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2011.

No description available.

Embedded generation (EG) provides many benefits in terms of reduction of system technical losses and increased load carrying capacity. In this study the sustainable EG carrying capacity permutations in a medium voltage distribution system, will be determined. Using these results, the financial investment recovery potential of EG will be studied and the impact on the cost recovery by the Utility as a result of compensating the EG at the current system marginal price, will be analysed. The study was done to show what capitalisation can be done on a medium voltage distribution system, by the owners of EG plant receiving revenue from the Utility, at the system margin price with the anticipated inflationary increases. The study will also cover the effect on the revenue stream of the Utility as a result of voltage changes caused by the EGs to the loads being supplied. The electrical system used in the study consisted of a radial system with distributed load and generation. The distributed loads were modelled using the average load capacity supplied by the Utility in medium voltage system. The average volume of sales lost as a result of non-technical losses was included in the load model so that the overall accuracy of the revenue effect by EG on the Utility, could be increased. The amount of capitalisation that is achievable by the owners of the EG was tested against various practical permutation scenarios, including variation of location, system impedance (different X/R ratios), time of operation and changing load volume and type. The extent of successful penetration of EG into the distribution system was found to be between 20% and 60% of the load carrying capacity of the system. The simulated results revealed “bathtub curve” behaviour for the cost of energy losses and this reconciled with the theoretical analysis of other studies done in this area. Lower volume penetration of EG results in higher investment potential of up to ten million rand per MW with a 5% MARR per year. This is very low when compared to the levelised cost of the expensive renewable energy technologies that are currently available in the market. With higher penetration of EG on low impedance systems, the gross contribution of the Utility is negatively affected which would introduce instability in the SMP yearly increases. / M. Sc. Eng. University of KwaZulu-Natal, Durban 2013.

Bibliography: leaves 238-248 / xxix, 248 leaves : ill. ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / This thesis is concerned with the design and coordination of linear, fixed parameter controllers for the purpose of enhancing the dynamic performance of a multimachine power system. The studies are based on linear control theory and involve state space analysis, modal analysis, eigenanalysis and conventional frequency response techniques. The emphasis is on the small-signal performance of the system / Thesis (Ph.D.)--University of Adelaide, Dept. of Electrical and Electronic Engineering, 1997?