Not available / text

The primary objective of the dissertation research is to establish the seismic demands of precast concrete floor diaphragms designed with an emerging design methodology. To accomplish this, three-dimensional (3D) finite element (FE) models of diaphragm-sensitive precast concrete structures have been developed by extending two-dimensional (2D) diaphragm model developed previously for nonlinear static "pushover" analyses. Using these models, diaphragm seismic demands under expected hazard are evaluated through the nonlinear transient dynamic analyses (NLTDA).The research work is composed of four major parts:(1) Developing 3D NLTDA analytical model for diaphragm-sensitive precast concrete structures: The 3D structure model is extended from a 2D FE diaphragm model developed by a previous researcher. This process involves properly handling comparability conditions in 3D, incorporating proper hysteresis behavior for the diaphragm reinforcement, and developing appropriate lateral force resisting system (LFRS) models. A sensitivity analysis is performed for 3D NLTDA modeling to assist in creating an appropriate model.(2) Application of the model in integrated analysis-driven physical testing: These experiments occurred at Lehigh University (LU) with project collaborators. The loading in these tests were controlled by NLTDA of the 3D analytical model. The tests were used to examine the seismic response of key joints (critical flexure and shear joints) in the diaphragm under realistic demands and to further calibrate the analytical model.(3) Analytical modeling in support of shake table testing: The shake table test was performed at University of California San Diego (UCSD). The test involved a half scale three-story diaphragm-sensitive precast concrete structure. NLTDA using the 3D analytical model is used to assist in design and performance prediction of the test specimen. The test results are being used to calibrate/verify the analytical model.(4) Calibrating design factors for the emerging diaphragm design methodology: In the last research step, the 3D analytical model is used to calibrate trial design factors for the emerging diaphragm design methodology. These factors are established based on a parametric study of NLDTA at different seismic hazard levels using simple structure configurations. These factors will be evaluated on models of realistic structures to determine design factors for the final design procedure.

No description available.

No description available.

No description available.

Thesis (Ph. D.)--Architecture, Georgia Institute of Technology, 2005. / Eastman, Charles M., Committee Chair ; Augenbroe, Godfried, Committee Co-Chair ; Navathe, Shamkant B., Committee Co-Chair ; Hardwick, Martin, Committee Member ; Sacks, Rafael, Committee Member. Vita. Includes bibliographical references.

Thesis (Ph. D.)--Lehigh University, 1997. / Includes vita. Includes bibliographical references (leaves 481-490).

Thesis (Ph. D.)--University of Texas at Austin, 2005. / Vita. Includes bibliographical references.

Orientadores: Newton de Oliveira Pinto Junior, Monica Pinto Barbosa / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Civil, Arquitetura e Urbanismo / Made available in DSpace on 2018-08-13T07:24:31Z (GMT). No. of bitstreams: 1 Ferraz_AndreLuizNonato_D.pdf: 9941000 bytes, checksum: 30542f4364161961a9bfdb7bfe736ac0 (MD5) Previous issue date: 2009 / Resumo: Foram avaliados neste trabalho, teórica e experimentalmente, o comportamento reológico e mecânico do concreto auto-adensável (C.A.A.), em específico suas características frente as deformações lentas, retração e fluência, e sua aplicabilidade em peças pré-moldadas. Foram desenvolvidos duas composições de concreto de classes de resistência distintas, 35 e 55 MPa. Na etapa de dosagem foram utilizados os procedimentos do método REPETTE-MELO, onde nas pastas e argamassas, foram realizados ensaios reométricos, ensaios de fluidez e Mini-Slump, e na definição do traço do C.A.A., ensaios de controle, tais como Slump-Flow, Funil em V, caixa em L, caixa em U e tubo em U, assim como ensaios das propriedades mecânicas tais como resistência à tração, resistência à compressão, e módulo de elasticidade. A avaliação do comportamento dos concretos frente a fluência se deu nas idades de 7, 14, 28, e 56 dias, segundo a NBR 8224 (ABNT, 1983), e frente a retração de acordo com a norma MERCOSUL NM 131:9. Os resultados experimentais foram comparados com valores de concretos convencionais disponíveis na literatura. Todos os ensaios foram realizados no Laboratório CESP de Engenharia Civil, e no Laboratório de Hidrologia da UNESP em Ilha Solteira-SP. No estudo da deformação rápida, ensaios de tração na flexão foram realizados aos 28 e 56 dias. Os coeficientes de fluência foram calculados quer seja através dos valores experimentais como pela NBR 6118 e comparados entre si, apresentando boa correlação, com diferenças menores que 10% para toda as idades. A composição do concreto auto-adensável foi implantada para fins de avaliação, junto a empresa de Pré- Moldados Protendit de São José do Rio Preto-SP, onde foram moldadas vigas, em escala real, as quais apresentaram melhor acabamento e se mostraram 50% mais economicas, em relação a mão-de-obra, quando comparada com a viga de concreto convencional. Os resultados obtidos mostram que as composições de concreto auto-adensável apresentam maiores valores de retração e fluência quanto comparados com concretos convencionais de mesma resistência mecânica. O C.A.A. de resistência à compressão igual a 55 MPa apresentou menor retração e fluência básica que o C.A.A. de resistência 35 MPa. / Abstract: This project analyzed, theoretically and experimentally, the mechanical and rheological behavior of the selfcompacting concrete (C.A.A.), specially its features according to slow deformation, shrinkage and creep, and its applicability in precast elements. Two compositions of concrete of different classes of resistance were developed, 35 MPa and 55 MPa. In the stage of the dosage, the procedures of the method REPETTE-MELO were used, rheometrical tests, fluidness tests and Mini-Slump were carried out on the pastes and the mortars, and control tests, such as Slump-Flow, funnel V test, box L, box U and tube U, and mechanical properties tests, such as tensile strength, compression strength and elasticity module were used to define the C.A.A. feature. The evaluation of the concrete behavior by creep happened at ages of 7, 14, 28, and 56 days, according to NBR 8224 (ABNT, 1983), and by shrinkage according to MERCOSUL NM 131:9. The experimental results were compared with values from conventional concrete available in the literature. All tests were performed at CESP Civil Engineer Laboratory, and at Hydrology Laboratory of the UNESP in Ilha Solteira-SP. In the fast deformation study, traction tests in flexion were performed at 28 and 56 days. The creep coefficients were calculated either through experimental values as by the NBR 6118 and compared each other, showing a good correlation, with differences smaller than 10% for all ages. The composition of self-compacting concrete was established for evaluation, in partnership with precast elements company Protendit of São José do Rio Preto-SP, where were shaped beams, in real scale, which showed better finishing and they showed themselves 50% more economical regarding labor, when compared with conventional concrete beam. The results reached show that the compositions of self-compacting concrete present higher values of shrinkage and creep when compared with conventional concrete of same strength. The C.A.A. that presented compression strength equal to 55 MPa showed a lower shrinkage and basic creep that C.A.A. strength of 35 MPa. / Doutorado / Edificações / Doutor em Engenharia Civil

Ambient vibrations of a reinforced concrete tower structure were recordedand analyzed to obtain the natural frequencies, the associated mode shapes and an estimate of the equivalent viscous damping. The structure investigated consists of four concrete wall panels,rigidly connected at various levels and contains a light precast concrete stairwell. It is similar to typical components of larger structures,such as stairwells and elevator shafts or cores. The given information should be useful in offering details of the dynamic behaviour of this type of structural elements. The experimental results are compared with the theoretical results obtained from two- and three-dimensional dynamic analyses using matrix methods applied to linear elastic systems with lumped masses. An efficient computer program to find the eigenvalues and eigenvectors for this type of mathematical model is described. / Applied Science, Faculty of / Civil Engineering, Department of / Graduate