The objective of this research is to develop an embedded, wireless, energy-harvesting prototype (E-WEHP) that can power on and sustain embedded sensing functions using the power present in ambient wireless signals in urban areas. This research is part of a bigger effort towards greening RF circuits and applications in order to reduce their pollution foot-print. Pollution due to modern electronics is primarily caused by non-biodegradable packaging waste and batteries that form a big part of most electronics. Electronic waste can especially be a nuisance in RFID and wireless sensors that are mass-produced and widely-used in consumer items, buildings, industries, agriculture and transportation. The first part of this research effort addresses the issue of minimizing electronic packaging waste by characterizing and using biodegradable substrates such as Paper and Perfluoropolymer (PFA) as a dielectric material in RF circuits. Towards this goal, the first of its kind active wireless sensor modules made of biodegradable paper substrate using a clean and novel inkjet-printing technology is developed and successfully operated in the 900 MHz free ISM band. The second and third part of this research effort addresses the issue of battery waste by investigating the use of ambient solar and wireless radiation for powering RF and embedded electronics for wireless localization and sensing applications without the use of batteries. The second part of this work presents a unique solar-powered tag called SOLTAG that combines solar cells along with an RFID-type powering mechanism to implement a very low-cost, battery-less, semi-passive wireless-tag but with a much longer range than passive EPC-Gen2 RFID tags. A GPS-like, low-cost, vehicle-tracking system based on a received-signal-strength-indication method using SOLTAGs in vehicles and a wireless network of Mica-motes is successfully developed and tested with accuracy down to 1.62 meters The third and main part of this research work presents a novel embedded-wireless-energy-harvesting-prototype (E-WEHP) that can successfully power-on and sustain sensing and M2M peripherals in a 16-bit microcontroller using the power present in ambient, wireless, Digital-TV signals without the use of batteries. This work involves an in-depth characterization of OFDM signals used in Digital-TV broadcasts in Tokyo and Atlanta along with the design and development of the E-WEHP hardware and firmware that exploits the multi-carrier nature of such TV signals for powering itself at a range of over 6 km from the TV broadcast sources. This work opens up the possibility of pervasively powering sensor motes for applications such as environmental sensing, smart homes, structural health monitoring, security and internet of things without the environmental and logistical cost of periodic battery replacement and disposal.

Les travaux présentés dans ce mémoire s'inscrivent dans la thématique de la transmission d'énergie sans fil, appliquée à l'alimentation à distance de capteurs, de réseaux de capteurs et d'actionneurs à faible consommation. Cette étude porte sur la conception, la caractérisation, et la mesure d'un circuit Rectenna (Rectifying antenna) à double polarisation circulaire à 2.45 GHz, compact et à rendement de conversion RF-DC optimisé. Un outil d'analyse globale basé sur la méthode itérative a été développé et exploité pour valider la faisabilité de cette analyse. La diode Schottky a été modélisée en utilisant une impédance de surface. La rectenna à double polarisation circulaire, réalisée en technologie micro-ruban, a été validée expérimentalement. Elle est caractérisée par la rejection de la 2ème harmonique et une possibilité de recevoir les deux sens de polarisation LHCP et RHCP par l'intermédiaire de 2 accès. Le rendement mesuré avec une densité de puissance de 0.525 mW/cm² est de l'ordre de 63%, tandis que la tension DC obtenue aux bornes d'une charge optimale de 1.6 kohm est de 2.82 V / The work presented in this thesis is within the subject of wireless power transmission, power applied to the remote sensors, networks of sensors and actuators with low power consumption. This study focuses on the design, characterization, and measurement of a rectenna circuit (rectifying antenna) with dual circular polarization at 2.45 GHz, and optimisation of the conversion efficiency. A global analysis tool, based on the iterative method was developed and used to validate the feasibility of this concept by this method. The Schottky diode was modeled using surface impedance. The dual circular polarization rectenna with microstrip technology has been optimized and characterized experimentally operating at 2.45 GHz. It includes the property of harmonic rejections. Two accesses can receive either direction LHCP or RHCP sense. The conversion efficiency of 63% has been measured with a power density of 0.525 mW/cm². A DC voltage of 2.82V was measured across an optimum load of 1.6 kohm

Les travaux présentés dans ce mémoire s’inscrivent dans la thématique de la transmission d’énergie sans fil, appliquée à l’alimentation à distance de capteurs, de réseaux de capteurs et d’actionneurs à faible consommation. Cette étude porte sur la conception,l’optimisation, la réalisation et la mesure de circuits Rectennas (Rectifying antennas)compacts, à faible coût et à haut rendement de conversion RF-DC.Un outil d’analyse globale, basé sur la méthode des Différences Finies dans le Domaine Temporel (FDTD), a été développé et utilisé pour prédire avec précision la sortie DC des rectennas étudiées. Les résultats numériques obtenus se sont avérés plus précis et plus complets que ceux de simulations à base d’outils commerciaux. La diode Schottky a été rigoureusement modélisée, en tenant compte de ses éléments parasites et de son boîtier SOT23, et introduite dans le calcul itératif FDTD.Trois rectennas innovantes, en technologie micro-ruban, ont été développées,optimisées et caractérisées expérimentalement. Elles fonctionnent à 2.45 GHz et elles ne contiennent ni filtre d’entrée HF ni vias de retour à la masse. Des rendements supérieurs à 80% ont pu être mesurés avec une densité surfacique de puissance de l’ordre de 0.21 mW/cm²(E = 28 V/m). Une tension DC de 3.1 V a été mesurée aux bornes d’une charge optimale de1.05 k_, lorsque le niveau du champ électrique est égal à 34 V/m (0.31 mW/cm²).Des réseaux de rectennas connectées en série et en parallèle ont été développés. Les tensions et les puissances DC ont été doublées et quadruplées à l’aide de deux et de quatre éléments, respectivement. / The work presented in this thesis is included within the theme of wireless power transmission, applied to wireless powering of sensors, sensor nodes and actuators with low consumption. This study deals with the design, optimization, fabrication and experimental characterization of compact, low cost and efficient Rectennas (Rectifying antennas).A global analysis tool, based on the Finite Difference Time Domain method (FDTD),has been developed and used to predict with a good precision the DC output of studied rectennas. The packaged Schottky diode has been rigorously modeled, taking into account the parasitic elements, and included in the iterative FDTD calculation.Three new rectennas, with microstrip technology, have been developed and measured.They operate at 2.45 GHz and they don’t need neither input HF filter nor via hole connections. Efficiencies more than 80 % have been measured when the power density is 0.21mW/cm² (E = 28 V/m). An output DC voltage of about 3.1 V has been measured with anoptimal load of 1.05 k_, when the power density is equal to 0.31mW/cm² (34 V/m).Rectenna arrays, with series and parallel interconnections, have been developed and measured. Output DC voltages and powers have been doubled and quadrupled using two andfour rectenna elements, respectively.