Power amplifiers (PA) are typically the most power-consuming building blocks of RF transceivers. Therefore, the design of a high-efficiency radio frequency power amplifier is the most obvious solution to overcoming the battery lifetime limitation in the portable communication systems. A power amplifier's classes (A, AB, B, C, F, E, etc), and design techniques (Load-pull and large-signal S-parameters techniques) are presented. The design accuracy of class-A power amplifier based on the small-signal S-parameters was investigated, where compression in the power gain was used as an indicator for design accuracy. The effect of drain voltage variation on the power gain compression has been studied in this research. The class-E amplifier has a maximum theoretical efficiency of 100%. It consists of a single transistor that is driven as a switch and a passive load network. The passive load network is designed to minimize drain (collector) voltage and current waveforms overlapping, which minimize the output power dissipation. Two L-band class-E amplifiers are implemented in section 5.3. One of them is a lumped elements based circuit and the other is a transmission lines based circuit. Both circuits show good performance (60% PAD) over a wide bandwidth (1.0 GHz). In section 5.4, lumped elements and transmission lines based X-band class-E amplifiers are presented. Both circuits show good performance (62% PAD) over wide bandwidth (4.8 GHz). A new technique to improve the drain efficiency of the class-E amplifier has been proposed. This technique uses two passive networks. One of them is in a series with the shunt capacitor CS and the other is in a series with the transistor's source terminal. This technique shows improvement in the drain efficiency, which jumps from 62% to 82%. Last few years have seen an increase in the popularity of the wireless communication systems. As a result, the demand for compact, low-cost, and low power portable (Single-chip) transceivers has increased dramatically. Among the transceiver's building blocks is the power amplifier. Thus, there is a need for a low-cost power amplifier. A 900 MHz CMOS RF PA with one-watt output power and a high power added efficiency (68%) is presented in chapter 6. This PA can be used in the European standard for mobile communications (GSM) handset transmitter. / Ph. D.

No description available.

In today's digital world, information and communication technology accounts for 3% and 2% of the global power consumption and CO2 emissions respectively. This alarming figure is on an upward trend, as future telecommunications systems and handsets will become even more power hungry since new services with higher bandwidth requirements emerge as part of the so called 'future internet' paradigm. In addition, the mobile handset industry is tightly coupled to the consumer need for more sophisticated handsets with greater battery lifetime. If we cannot make any significant step to reducing the energy gap between the power hungry requirements of future handsets, and what battery technology can deliver, then market penetration for 4G handsets can be at risk. Therefore, energy conservation must be a design objective at the forefront of any system design from the network layer, to the physical and the microelectronic counterparts. In fact, the energy distribution of a handset device is dominated by the energy consumption of the RF hardware, and in particular the power amplifier design. Power amplifier design is a traditional topic that addresses the design challenge of how to obtain a trade-off between linearity and efficiency in order to avoid the introduction of signal distortion, whilst making best use of the available power resources for amplification. However, the present work goes beyond this by investigating a new line of amplifiers that address the green initiatives, namely green power amplifiers. This research work explores how to use the Doherty technique to promote efficiency enhancement and thus energy saving. Five different topologies of RF power amplifiers have been designed with custom-made signal splitters. The design core of the Doherty technique is based on the combination of a class B, class AB and a class C power amplifier working in synergy; which includes 90-degree 2-way power splitter at the input, quarter wavelength transformer at the output, and a new output power combiner. The frequency range for the amplifiers was designed to operate in the 3.4 - 3.6 GHz frequency band of Europe mobile WiMAX. The experimental results show that 30dBm output power can be achieved with 67% power added efficiency (PAE) for the user terminal, and 45dBm with 66% power added efficiency (PAE) for base stations which marks a 14% and 11% respective improvement over current stateof- the-art, while meeting the power output requirements for mobile WiMAX applications.