This thesis introduces low-cost implementations for the next generation distributed antenna system (DAS) using analogue radio over fibre. A multiple-input-multiple-output (MIMO) enabled radio over fibre (RoF) system using double sideband (DSB) frequency translation system is proposed. In such a system, the 2x2 MIMO signals can be transmitted to the remote antenna units (RAUs) from the base station via a single optical link. By using the DSB frequency translation, the original single-input-single-output (SISO) DAS can be upgraded into the MIMO DAS without implementing parallel optical links. Experimentally, the DSB frequency translation 2x2 MIMO RoF system transmits 2x2 LTE MIMO signals with 20MHz bandwidth in each channel via a 300m MMF link. The condition number of the system is < 10dB within the power equaliser bandwidth which means the MIMO system is well-conditioned and the crosstalk between the channels can be compensated by the MIMO signal processing. To install the DSB frequency translation system in a wideband service-agnostic DAS, the original MIMO signals need to be translated into unoccupied frequency bands over the DAS, which are usually occupied by specific applications that are not to be transmitted over the DAS. The frequency spectrum allocation of the wireless services is analysed showing that by choosing a particular LO frequency (2.2GHz in the UK), in the DSB frequency translation system, the original MIMO signals can always be translated into unoccupied frequency bands so that the same infrastructure can support multiple services. The idea of DSB frequency translation system can not only support MIMO radio over fibre but can also improve the SFDR of a general radio over fibre system. Because when the upper sideband and the lower sideband of the signal after translation are converted back to the original frequency band, the noise adds incoherently but the signals add-up coherently, this gives the system theoretically 2dB 3rd order SFDR improvement. If the idea of the DSB frequency translation is extended into a higher number of sidebands, the system SFDR can be further improved. Experimentally, the system 3rd order SFDR can be improved beyond the intrinsic optical link by 2.7dB by using quadruple sideband (QSB) frequency translation. It means the optical bandwidth in a general RoF system can be traded for the electrical SFDR. By integrating the analogue and the digital RoF systems, a hybrid DAS has been demonstrated, showing that the EVM dynamic range for the 4G LTE service (using digital RoF link) can be improved to be similar to the 3G UMTS service (using analogue RoF link), so that fewer number of RAUs for the LTE services are needed.

The aim of the research presented in this thesis is to develop photonic integrated circuit (PIC) for Radio-over-Fiber (RoF) application. As such, at the beginning of the thesis, a dual-function photonic integrated circuit for microwave photonic applications is proposed. The photonic circuit is arranged to have two separate output ports, and depending upon the RF input signal strength, it provides either tunable millimeter wave carriers by frequency octo-tupling of the RF signal or frequency up-conversion of a microwave signal from the electrical to the optical domain. The circuit exploits the intrinsic relative phases between the ports of multi-mode interference couplers (MMI) to provide all the static optical phases needed, hence drift free. In the middle of thesis, a generalized architecture having N parallel phase modulators driven electrically with a progressive 2π⁄N phase shift is analyzed. The proposed design is justified by computer simulation for N=8 architecture with properly determined optical phase shifts to generate frequency multiplication of an electrical signal. The front- and back-end of the circuit comprises 4×4 MMI couplers enclosing an array of four pairs of phase modulators and 2×2 MMI couplers. The proposed design for frequency multiplication requires no optical or electrical filters; the operation is not limited to carefully adjusted modulation indexes. Later on, a generalized approach for achieving frequency multiplication using two cascades MZM is presented. The proposed design consists of a Mach-Zehnder interferometer with each arm containing a pair of Mach-Zehnder modulators (MZM) in series as a means of optoelectronic frequency multiplication (octo-tupling and quattourviginti-tupling). The circuit requires no electrical or optical filters. There is no requirement to carefully adjust the modulation index to achieve correct operation of the octo-tupler. A comparison is made with an alternative functionally equivalent single-stage parallel MZM circuit discussed herein the thesis. Finally, the thesis describes the generation of the same magnitude but opposite sign high order single optical side band from its output ports by using a RF source. A single stage parallel Mach-Zehnder Modulator (MZM) and a two-stage series parallel MZM architecture is described and their relative merits and demerits discussed. As an illustration of a prospective application it is shown how the circuit may be used to transport radio signals over fibre for wireless access; generating remotely a mm-wave carrier modulated by digital IQ data. A detail calculation of symbol error rate is presented to characterise the system performance. A mathematical analysis is provided to describe the principle of operation for all the proposed design and validated by commercially available industrial standard simulation tool.

In this thesis a Fully-Photonic DRoF (FP-DRoF) system is proposed for deploying of future super-broadband access networks. Digital Radio over Fibre (DRoF) is more independent of the fibre network impairments and the length of fibre than the ARoF link. In order for fully optical deployment of the signal conversion techniques in the FP-DRoF architecture, two key components an Analogue-to-Digital Converter (ADC) and a Digital-to-Analogue Converter (DAC)) for data conversion are designed and their performance are investigated whereas the physical functionality is evaluated. The system simulation results of the proposed pipelined Photonic ADC (PADC) show that the PADC has 10 GHz bandwidth around 60 GHz of sampling rate. Furthermore, by changing the bandwidth of the optical bandpass filter, switching to another band of sampling frequency provides optimised performance condition of the PADC. The PADC has low changes on the Effective Number of Bit (ENOB) response versus analogue RF input from 1 GHz up to 22 GHz for 60 GHz sampling frequency. The proposed 8-Bit pipelined PADC performance in terms of ENOB is evaluated at 60 Gigasample/s which is about 4.1. Recently, different methods have been reported by researchers to implement Photonic DACs (PDACs), but their aim was to convert digital electrical signals to the corresponding analogue signal by assisting the optical techniques. In this thesis, a Binary Weighted PDAC (BW-PDAC) is proposed. In this BW-PDAC, optical digital signals are fully optically converted to an analogue signal. The spurious free dynamic range at the output of the PDAC in a back-to-back deployment of the PADC and the PDAC was 26.6 dBc. For further improvement in the system performance, a 3R (Retiming, Reshaping and Reamplifying) regeneration system is proposed in this thesis. Simulation results show that for an ultrashort RZ pulse with a 5% duty cycle at 65 Gbit/s using the proposed 3R regeneration system on a link reduces rms timing jitter by 90% while the regenerated pulse eye opening height is improved by 65%. Finally, in this thesis the proposed FP-DRoF functionality is evaluated whereas its performance is investigated through a dedicated and shared fibre links. The simulation results show (in the case of low level signal to noise ratio, in comparison with ARoF through a dedicated fibre link) that the FP-DRoF has better BER performance than the ARoF in the order of 10-20. Furthermore, in order to realize a BER about 10-25 for the ARoF, the power penalty is about 4 dBm higher than the FP-DRoF link. The simulation results demonstrate that by considering 0.2 dB/km attenuation of a standard single mode fibre, the dedicated fibre length for the FP-DRoF link can be increased to about 20 km more than the ARoF link. Moreover, for performance assessment of the proposed FP-DRoF in a shared fibre link, the BER of the FP-DRoF link is about 10-10 magnitude less than the ARoF link for -19 dBm launched power into the fibre and the power penalty of the ARoF system is 10 dBm more than the FP-DRoF link. It is significant to increase the fibre link’s length of the FP-DRoF access network using common infrastructure. In addition, the simulation results are demonstrated that the FP-DRoF with non-uniform Wavelength Division Multiplexing (WDM) is more robust against four wave mixing impairment than the conventional WDM technique with uniform wavelength allocation and has better performance in terms of BER. It is clearly verified that the lunched power penalty at CS for DRoF link with uniform WDM techniques is about 2 dB higher than non-uniform WDM technique. Furthermore, uniform WDM method requires more bandwidth than non-uniform scheme which depends on the total number of channels and channels spacing.

Next generation access networks should be able to cultivate the ongoing evolution in services and applications. Advancements on that front are expected to exhibit the transformation of high definition television (HDTV) and 2D services into ultra-HDTV and individual interactive 3D services. Currently deployed passive optical networks (PONs) have been certified to be able to deliver high quality video and internet services while in parallel broadband wireless standards are increasing their spectral efficiency and subscriber utilisation. Exploiting the benefits of both by providing an integrated infrastructure benefiting from the wireless mobility and ease of scalability and escalating bandwidth of next generation PONs are expected to offer service providers the business models justifying the evolved services. In this direction, this thesis deals with the means of transparent routing of standard worldwide interoperability for microwave access (WiMAX) signal formats over legacy PONs to and from wireless end users based on radio over fibre (RoF). The concept of frequency division multiplexing (FDM) with RoF is used for efficient addressing of individual base stations, bandwidth on-demand provisioning across a cell/sector, simple remote radio heads and no interference with the baseband PON spectrum. Network performance evaluation, initially through simulation, has displayed, in the presence of optical non-linearites and multi-path wireless channels, standard error vector magnitudes (EVMs) at remote radio receivers and bit error rates (BERs) of 1E-4 for typical WiMAX rates bidirectionally. To provide enhanced scalability and dynamicity, a newly applied scheme based on extended wavelength band overlay over the splitter, wireless-enabled PONs has been progressively investigated. This allows for the routing of multiple FDM windows to different wavelengths resulting in significantly reduced optical and electrical component costs and no dispersion compensation over the fibre. This has been implemented through the application of a dense array wave guide grating (AWG) and tuneable filter in the optical line terminal (OLT) and optical network unit/base stations (ONU/BSs) respectively. Although with the use of a splitter the distribution point of the optical network remains largely the same, vertical cavity surface emitting laser (VCSEL) arrays provide colourless upstream transmission. In addition, an overlapping cell concept is developed and adopted for increased wireless spectral efficiency and resilience. Finally, an experimental test-bed using commercially available WiMAX transceivers was produced, which enabled repetition of the simulation outcomes and therefore confirmed the overall network performance.

The proliferation of data hungry wireless devices, such as smart phones and intelligent sensing networks, is pushing modern wireless networks to their limits. A significant shortfall in the ability of networks to meet demand for data is imminent. This thesis addresses this problem through examining the design of distributed antenna systems (DAS) to support next generation high speed wireless services that require high densities of access points and must support multiple-input multiple-output (MIMO) protocols. First, it is shown that fibre links in DAS can be replaced with low-cost, broadband free-space optical links, termed radio over free-space optics (RoFSO) links. RoFSO links enable the implementation of very high density DAS without the need for prohibitively expensive cabling infrastructure. A 16m RoFSO link requiring only manual alignment is experimentally demonstrated to provide a spurious-free dynamic range (SFDR) of > 100dB/Hz^2/3 over a frequency range from 300MHz- 3.1GHz. The link is measured to have an 802.11g EVM dynamic range of 36dB. This is the first such demonstration of a low-cost broadband RoFSO system. Following this, the linearity performance of RoFSO links is examined. Because of the high loss nature of RoFSO links, the directly-modulated semiconductor lasers they use are susceptible to high-order nonlinear behaviour, which abruptly limits performance at high powers. Existing measures of dynamic range, such as SFDR, assume only third-order nonlinearity and so become inaccurate in the presence of dominant high-order effects. An alternative measure of dynamic range called dynamic-distortion-free dynamic range (DDFDR) is then proposed. For two different wireless services it is observed experimentally that on average the DDFDR upper limit predicts the EVM knee point to within 1dB, while the third-order SFDR predicts it to within 6dB. This is the first detailed analysis of high-order distortion effects in lossy analogue optical links and DDFDR is the first metric able to usefully quantify such behaviour. Next, the combination of emerging MIMO wireless protocols with existing DAS is examined. It is demonstrated for the first time that for small numbers of MIMO streams (up to ~4), the capacity benefits of MIMO can be attained in existing DAS installations simply by sending the different MIMO spatial streams to spatially separated remote antenna units (RAU). This is in contrast to the prevailing paradigm of replicating each MIMO spatial stream at each RAU. Experimental results for two representative DAS layouts show that replicating spatial streams provides an increase of only ~1% in the median channel capacity over merely distributing them. This compares to a 3-4% increase of both strategies over traditional non-DAS MIMO. This result is shown to hold in the multiple user case with 20 users accessing 3 base stations. It is concluded that existing DAS installations offer negligible capacity penalty for MIMO services for small numbers of spatial streams, including in multi-user MIMO scenarios. Finally, the design of DAS to support emerging wireless protocols, such as 802.11ac, that have large numbers of MIMO streams (4-8) is considered. In such cases, capacity is best enhanced by sending multiple MIMO streams to single remote locations. This is achieved using a novel holographic mode division multiplexing (MDM) system, which sends each separate MIMO stream via a different propagation mode in a multimode fibre. Combined channel measurements over 2km of mode-multiplexed MMF and a typical indoor radio environment show in principle a 2x2 MIMO link providing capacities of 10bit/s/Hz over a bandwidth of 6GHz. Using a second experimental set-up it is shown that the system could feasibly support at least up to a 4x4 MIMO system over 2km of MMF with a condition number >15dB over a bandwidth of 3GHz, indicating a high degree of separability of the channels. Finally, it is shown experimentally that when a fibre contains sharp bends (radius between 20mm and 7.2mm) the first 6 mode-groups used for multiplexing exhibit no additional power loss or cross-coupling compared with unbent fibre, although mode-groups 7, 8 and 9 are more severely affected. This indicates that at least 6x6 multiplexing is possible in standard installations with tight fibre bends.

This thesis investigates the generation and radio-over-fibre (RoF) transport of unlicensed 60 GHz millimetre-wave (mm-wave) frequency band. The investigated benefits of transmission schemes applicable for the mm-wave generation include optical carrier suppression (OCS), optical frequency multiplication (OFM) and remote heterodyne detection (RHD). For the in-door cabling of the mm-wave transmission, a low-cost polymer optical fibre (POF) along with bend-insensitive single mode fibre (BI-SMF) has been investigated for short-range networks. Transporting mm-wave generated signals over POF and BI-SMF cables based on OCS scheme showed results with the highest spectral efficiency and least inter-symbol interference over a 2.5 Gbit/s data delivery. Based on this thesis analysis, OCS simulation of POF showed the most reliable power penalty performance and receiver sensitivity at 30-m whilst the BI-SMF fiber produced equal observations at 150-m and more. In observing the free space links of delivering the RoF signal, the attenuation on the received signal power for both POF and BI-SMF was insignificant but expected, as the simulation assumed complete and total collimation of the light beams onto the aperture of the photodetector. OCS scheme for mm-wave generation and transport was explored based on the cost effectiveness of using one external modulator compared to other generation schemes that utilised more than one external modulator. OFM scheme was simulated to transport LTE and Wi-Fi signals along with 60 GHz RF band through both SMF and MMF-POF/BI-SMF cables. OFM transport scheme produced the highest attenuation on LTE, Wi-Fi and mm-wave signals carrying 100 Mbit/s data as simulated POF lengths increased. The best performance POF length was observed at 10-m. The application of offset launch technique at the coupling of SMF and POF showed insignificant improvement on signal bandwidth. The free space OFM transmission also demonstrated negligible change to the received signal power. This reinforces the attributes of deploying OWC system in an in-door environment. In other investigation, the simulated successful delivery of mm-wave signal using RHD scheme modulated and transported 10 Gbit/s data signal over POF and BI-SMF cables. Additional observed unrecorded result also showed BI-SMF cable maintained a 2% reduction of received power for 450-m fiber cable from 150-m. The attributes to RHD includes its low operating power system application and delivery of localised 60 GHz signal for uplink RoF transmission. The conceptualised design of Gigabit data delivery for indoor customer applications either through POF or BI-SMF cable, transporting various wireless channels has been presented in this thesis for the design of a robust next generation Broadband access network to reinforce the fiber-inside-the-home (FiTH) deployment.

The most important fact in the mobile industry at the moment is that demand for wireless services will continue to expand in the coming years. Therefore, it is vital to find more spectrums through cognitive radios for the growing numbers of services and users. However, the spectrum reallocations, enhanced receivers, shared use, or secondary markets-will not likely, by themselves or in combination, meet the real exponential increases in demand for wireless resources. Network operators will also need to re-examine network architecture, and consider integrating the fibre and wireless networks to address this issue. This thesis involves driving fibre deeper into cognitive networks, deploying microcells connected through fibre infrastructure to the backbone LTE networks, and developing the algorithms for diverting calls between the wireless and fibre systems, introducing new coexistence models, and mobility management. This research addresses the network deployment scenarios to a microcell-aided cognitive network, specifically slicing the spectrum spatially and providing reliable coverage at either tier. The goal of this research is to propose new method of decentralized-to-distributed management techniques that overcomes the spectrum unavailability barrier overhead in ongoing and future deployments of multi-tiered cognitive network architectures. Such adjustments will propose new opportunities in cognitive radio-to-fibre systematic investment strategies. Specific contributions include: 1) Identifying the radio access technologies and radio over fibre solution for cognitive network infrastructure to increase the uplink capacity analysis in two-tier networks. 2) Coexistence of macro and microcells are studied to propose a roadmap for optimising the deployment of cognitive microcells inside LTE macrocells in the case of considering radio over fibre access systems. 3) New method for roaming mobiles moving between microcells and macrocell coverage areas is proposed for managing spectrum handover, operator database, authentication and accounting by introducing the channel assigning agent entity. The ultimate goal is to reduce unnecessary channel adaptations.

In this thesis, a fully millimetre-wave (mm-wave) generation and transmission system is proposed for futuristic communications. Significant challenges have been dealt with regarding the proposed system, including designing the mm-wave generation and transmission technique, and its application in cellular networks. These challenges are presented through five main contributions and validated via Optiwave Design Software and MATLAB simulation tools. Firstly, three novel photonic generation methods are proposed and designed based on the characteristics of Brillouin fibre laser and the Stimulated Brillouin Scattering (SBS) effects with phase modulation. The mm-wave carriers are successfully generated with a tuning capability from 5 to 90 GHz. Also, these carriers are with good Signal to Noise Ratio (SNR) up to 51 dB, and low noise signal power of about -40 dBm. The impact of these methods is obtaining stable mm-waves appropriate for Radio over Fibre (RoF) transmission systems in 5G optical networks. Secondly, a full-duplex RoF system with the generation of a 64 GHz mm-wave is proposed. Successful transmission of the mm-wave over a fibre link is achieved for up to 100 km of fibre with a data rate of 5 Gbits/s. The main impact of this system is cost reduction and performance improvement by simplifying mm-wave generation and transmission over fibre. Also, it ensures a useful communication link for small cell networks. Thirdly, a hybrid Fibre/Free-space optical (FSO) system for the generation and transmission of 64 GHz mm-wave is proposed. This optical system provides a low latency communication link and overcomes mm-wave high path losses. A successful mm-wave transmission is achieved over a 10 km fibre length, and 2 km FSO link length with a good Bit Error Rate (BER) of about 1.5×10-13 and a data rate of 10 Gbits/s. This system increases the network coverage area by transmitting the mm-wave over the FSO link to the areas with natural obstacles the laying of fibre cables impossible. Also, it can be used as an effective solution under emergency disaster conditions. Fourthly, a comprehensive study of the wireless propagation performance for different mm-wave bands (28, 60, and 73 GHz) as cellular networks is investigated and compared with the 2.4 GHz Ultra-High Frequency band (UHF). A map-based scenario is proposed for the deployment of Base Stations (BSs) within the Brunel University London Campus map to consider real blockage effects. This investigation involved specifying which mm-wave spectrum can enhance the futuristic cellular networks, by evaluating the coverage and rate trends. Comparative results show that the 73 GHz bands can achieve the higher rate with good coverage and the lowest interference effects than the other mm-wave bands. Finally, a simplified path loss model is proposed to estimate precisely the 28 GHz mm-wave performance, which is considered a key component in 5G networks in outdoor applications. The proposed path loss model captures the diffraction and specular reflection impacts on mm-wave wireless propagation.

Optical fibre has become the dominant theme of transmission in long haul, high data rate communication systems due to its tremendous bandwidth and low loss. Radio over Fibre (RoF) technology facilitates the seamless integration between wireless and optical communication systems and found to be the most promising solution to meet the exponential bandwidth demands expected for the upcoming years. However, the main bit-rate/distance limitation in RoF systems is the chromatic dispersion. In this thesis, the two generations of RoF technologies, namely Analogue RoF (ARoF) and Digital RoF (DRoF) are investigated. The overall aim of this research is to optimise the optical bandwidth utilisation of these two approaches for a typical transmission of the fronthaul link proposed in the next generation Centralised Radio Access Network (C-RAN). Consequently, a number of physical layer design scenarios for the optimised transmission of the Radio Frequency (RF) signals over a Standards Single Mode Fibre (SSMF) are demonstrated. Firstly, for an ARoF transmission, where the analogue RF signals are transported over SSMF using an optical carrier, a bidirectional link transmitting four Downlink/Uplink channels in a chromatic dispersion limited scenario is designed. Simulation results have shown a clear constellation diagram of a 2.5 Gb/s RF signal transmission over 120 km fibre length. Secondly, a DRoF system with reduced optical bandwidth occupancy is proposed. This system employs an optical Duobinary transmission to the digitised RF signal at the transmitter side to reduce its spectrum and to address the chromatic dispersion effect, simultaneously. Simulation results demonstrate the capability of the proposed system to maintain high-quality transmission of the digitised signals over 70 km of fibre distance without dispersion compensation requirements. Finally, an advanced DRoF transmission link based on integrating digital Optical Single Sideband (OSSB) transmission with Duobinary encoding scheme is designed. Simulation results have clearly verified system's robustness against transmission impairments and have better performances in terms of the obtained BER and EVM with respect to the 3GPP standardised values. Moreover, the results show that both transmission distance and power budget are furtherly improved in comparison with two other digital transmission scenarios.

During the last three decades, the significant increase in electricity demand, and its consequences, has appeared as a serious concern for the utility companies, but no major changes have been applied to the conventional power grid infrastructure. Recently, researchers have identified efficient control and power distribution mechanisms as the immediate challenges for conventional power grids. The next step for conventional power grid towards the Smart Grid is to provide energy efficiency management along with higher reliability via smart services, in which the application of Information and Communication Technology (ICT) is inevitable. ICT introduces powerful tools to comply with the smart grid requirements. Among various ICT properties, the telecommunication network plays a key role for providing a secure infrastructure. The two-way digital communication system provides an interaction between energy suppliers and consumers for managing, controlling and optimizing energy distribution. We can also define the smart grid as a two-way flow of energy and control information, where the electricity consumers can generate energy using green energy resources. The main objective of this thesis is to select an effective data communication infrastructure to support the smart grid services by considering a hybrid wireless and optical communication technologies. Radio-over-Fibre (RoF) networks are considered as a potential solution to provide a fast, reliable and efficient network backbone with the optical access network integration and the flexibility and mobility of the wireless network. Therefore, we adopt the integration of RoF to Passive Optical Network (PON) as a broadband access network to transmit smart grid data along with the Fiber to the Home/Building/Curb (FTTx) traffic through the shared fibre, and utilizing Wavelength Division Multiplexing (WDM). Finally, we present and analyze the simulation results for the aforementioned infrastructure based on our enhanced ROF-PON integration model.