No description available.

No description available.

The Vanadium bromide (V/Br) flow cell employs the Br3-/Br- couple in the positive and the V(II)/V(III) couple in the negative half cell. One major issue of this flow cell is bromine gas formation in the positive half cell during charging which results from the low solubility of bromine in aqueous solutions. Bromine complexing agents previously used in the zinc-bromine fuel cell were evaluated for their applicability in V/Br flow cell electrolytes. Three quaternary ammonium bromides: N-ethyl-N-methyl-morpholinium bromide (MEM), N-ethyl-N-methyl-pyrrolidinium bromide (MEP) and Tetra-butyl ammonium bromide (TBA) were studied. It is known that aqueous bromine reacts with quaternary ammonium bromides to form an immiscible organic phase. Depending on the number of quaternary ammonium bromides used and the environmental temperature, the second phase formed will either be solid or liquid. As any solid formation would interrupt the flow cell operation, potential formation of such kind has to be eliminated. Stability tests of simulated V/Br electrolyte with added quaternary ammonium bromides were carried out at 11, 25 and 40 oC. In the absence of bromine, the addition of MEM, MEP and TBA were found to be stable in V/Br electrolytes. However, in the presence of bromine, solid formation was observed in the bromine rich organic phase when the V/Br electrolyte contained a single quaternary ammonium bromide (QBr) compound. For V/Br electrolytes with binary or ternary QBr mixtures containing TBA, the presence of bromine caused a viscous polybromide phase to form at room temperature and the release of bromine gas at higher temperature. Only a binary mixture of MEM and MEP formed a stable liquid organic phase between 11 ?? 40 oC. In this study it was found that V/Br electrolytes containing a binary QBr mixture (0.75M) of MEM and MEP gave the best combination that formed an orange oily layer in the presence of bromine without solidification between 11 ?? 40oC. Furthermore, it was found that samples of V/Br electrolytes containing a ternary QBr mixture, are less effective in bromine capturing if the total QBr concentration was less than 1 M at 40oC, where bromine gas evolution was observed. From electrochemical studies of V3+/V2+, it was found that the addition of MEM and MEP had a minimal effect on the formal potential of the V3+/V2+ couple, the V2+/V3+ transfer coefficient and the diffusion coefficient of V3+. Therefore, MEM and MEP can be added to the negative half-cell of a V/Br flow cell without major interference From linear sweep voltammetry, the kinetics of the Br-/Br3- redox couple was found to be mass transfer controlled. After the addition of MEM and MEP mixture, the exchange current density was found to decrease from 0.013 Acm-2 to 0.01 Acm-2. On the other hand the transfer coefficient before and after MEM and MEP addition was found to be 0.5 and 0.44 respectively. Since the kinetic parameters were not significantly affected by the addition of MEM and MEP mixture, they can be added to the positive half-cell of the V/Br flow cell as bromine complexing agents. The electrochemical studies of both V3+/V2+ and Br-/Br3- showed the addition of MEM and MEP has minimal interference with the redox reactions of the vanadium bromide flow cell. This thesis also investigated the effect of MEM and MEP addition on the cell performance of a lab scale V/Br flow cell using two different membranes (ChiNaf and VF11). Flow cell performance for 2 M V3.7+ + 0.19 M MEM + 0.56 M MEP electrolytes utilising ChiNaf membrane at 10 mAcm-2 produced an energy efficiency of 59%, and this decreased to 43% after 15 cycles. For the static cell utilising VF11 membrane, the addition of MEM and MEP reduced the energy efficiency from 59.7% to 43.4%. It is believed that this is caused by the mass transfer controlled Br-/Br3- couple in the complexed positive half-cell solution. Therefore, uniformity between the organic and aqueous phase is important for flow cells utilising electrolytes with MEM and MEP. Finally, the polarization resistance of a lab scale V/Br flow cell utilising ChiNaf membrane and 2 M V3.7+ electrolytes was found to be slightly higher during cell charging (3.9 cm2) than during the discharge process (3.6 cm2), which is opposed to that in the all-vanadium redox cell.

A redox flow battery (RFB) is an electrochemical energy storage device in which the storage medium is in the form of liquid electrolyte, which is stored in external reservoirs separate from the cell stack. The storage capacity of such systems is limited by the size of the external tanks, making the RFB an ideal technology for grid level energy storage. The vanadium redox flow battery (VRB) is a particularly attractive variant of the RFB, due to its use of a single transition-metal element in both the positive and negative electrolytes. However, the performance of the VRB is affected by the cross-over of electrolytes through the ion-exchange membrane which separates the positive and negative electrolytes. Cross-over causes degradation of energy storage efficiency and long term capacity loss. Previous studies of ion cross-over have focused primarily on the measurement of ion diffusion across ion exchange membranes in the absence of electrical current. In this work a novel VRB cell is described in which ion cross-over can be measured directly in the presence and absence of electrical current. Measurements are made of cross-over using this cell with three different types of ion exchange membrane in both charge and discharge modes. The results reported in this work show that the rate of ion cross-over can be greatly enhanced or suppressed depending upon the magnitude of the current flow and its direction relative to the ion concentration gradient. / text

The Vanadium bromide (V/Br) flow cell employs the Br3-/Br- couple in the positive and the V(II)/V(III) couple in the negative half cell. One major issue of this flow cell is bromine gas formation in the positive half cell during charging which results from the low solubility of bromine in aqueous solutions. Bromine complexing agents previously used in the zinc-bromine fuel cell were evaluated for their applicability in V/Br flow cell electrolytes. Three quaternary ammonium bromides: N-ethyl-N-methyl-morpholinium bromide (MEM), N-ethyl-N-methyl-pyrrolidinium bromide (MEP) and Tetra-butyl ammonium bromide (TBA) were studied. It is known that aqueous bromine reacts with quaternary ammonium bromides to form an immiscible organic phase. Depending on the number of quaternary ammonium bromides used and the environmental temperature, the second phase formed will either be solid or liquid. As any solid formation would interrupt the flow cell operation, potential formation of such kind has to be eliminated. Stability tests of simulated V/Br electrolyte with added quaternary ammonium bromides were carried out at 11, 25 and 40 oC. In the absence of bromine, the addition of MEM, MEP and TBA were found to be stable in V/Br electrolytes. However, in the presence of bromine, solid formation was observed in the bromine rich organic phase when the V/Br electrolyte contained a single quaternary ammonium bromide (QBr) compound. For V/Br electrolytes with binary or ternary QBr mixtures containing TBA, the presence of bromine caused a viscous polybromide phase to form at room temperature and the release of bromine gas at higher temperature. Only a binary mixture of MEM and MEP formed a stable liquid organic phase between 11 ?? 40 oC. In this study it was found that V/Br electrolytes containing a binary QBr mixture (0.75M) of MEM and MEP gave the best combination that formed an orange oily layer in the presence of bromine without solidification between 11 ?? 40oC. Furthermore, it was found that samples of V/Br electrolytes containing a ternary QBr mixture, are less effective in bromine capturing if the total QBr concentration was less than 1 M at 40oC, where bromine gas evolution was observed. From electrochemical studies of V3+/V2+, it was found that the addition of MEM and MEP had a minimal effect on the formal potential of the V3+/V2+ couple, the V2+/V3+ transfer coefficient and the diffusion coefficient of V3+. Therefore, MEM and MEP can be added to the negative half-cell of a V/Br flow cell without major interference From linear sweep voltammetry, the kinetics of the Br-/Br3- redox couple was found to be mass transfer controlled. After the addition of MEM and MEP mixture, the exchange current density was found to decrease from 0.013 Acm-2 to 0.01 Acm-2. On the other hand the transfer coefficient before and after MEM and MEP addition was found to be 0.5 and 0.44 respectively. Since the kinetic parameters were not significantly affected by the addition of MEM and MEP mixture, they can be added to the positive half-cell of the V/Br flow cell as bromine complexing agents. The electrochemical studies of both V3+/V2+ and Br-/Br3- showed the addition of MEM and MEP has minimal interference with the redox reactions of the vanadium bromide flow cell. This thesis also investigated the effect of MEM and MEP addition on the cell performance of a lab scale V/Br flow cell using two different membranes (ChiNaf and VF11). Flow cell performance for 2 M V3.7+ + 0.19 M MEM + 0.56 M MEP electrolytes utilising ChiNaf membrane at 10 mAcm-2 produced an energy efficiency of 59%, and this decreased to 43% after 15 cycles. For the static cell utilising VF11 membrane, the addition of MEM and MEP reduced the energy efficiency from 59.7% to 43.4%. It is believed that this is caused by the mass transfer controlled Br-/Br3- couple in the complexed positive half-cell solution. Therefore, uniformity between the organic and aqueous phase is important for flow cells utilising electrolytes with MEM and MEP. Finally, the polarization resistance of a lab scale V/Br flow cell utilising ChiNaf membrane and 2 M V3.7+ electrolytes was found to be slightly higher during cell charging (3.9 cm2) than during the discharge process (3.6 cm2), which is opposed to that in the all-vanadium redox cell.

Continued emission of green house gases has energized research activity worldwide to develop efficient ways to harness renewal energy. The availability of large scale energy storage technologies is essential to make renewal energy a reliable source of energy. Redox flow batteries show potential in this direction. These batteries typically need expensive membranes which need replacement be-cause of fouling. The recently proposed soluble lead redox flow battery (SLRFB), in which lead ions deposit on electrodes in charge cycle and dissolve back in discharge cycle, can potentially cut down the cost of energy storage by eliminating membrane. A number of challenges need to be overcome though. Low cycleability, residue formation, and low efficiencies are foremost among these, all of which require an understanding of the underlying mechanisms. A model of laminar flow-through SLRFB is first developed to understand buildup of residue on electrodes with continued cycling. The model accounts for spatially and temporally growing concentration boundary layers on electrodes in a self consistent manner by permitting local deposition/dissolution rates to be controlled by local ion transport and reaction conditions. The model suggests controlling role for charge transfer reaction on electrodes (anode in particular) and movement of ions in the bulk and concentration boundary layers. The non-uniform current density on electrodes emerges as key to formation of bare patches, steep decrease in voltage marking the end of discharge cycle, and residue buildup with continuing cycles. The model captures the experimental observations very well, and points to improved operational efficiency and decreased residue build up with cylindrical electrodes and alternating flow direction of recirculation. The underlying mechanism for more than an order of magnitude increase in cycle life of a beaker cell battery with increase in stirrer speed is unraveled next. Our experiments show that charging with and without stirring occurs identically, which brings up the hitherto unknown but quite strong role of natural convection in SLRFB. The role of stirring is determined to be dislodgement/disintegration of residue building up on electrodes. The depletion of active material from electrolyte due to residue formation is offset by “internal regeneration mechanism”, unraveled in the present work. When the rate of residue formation, rate of dislodging/disintegration from electrode, and rate of regeneration of active material in bulk of the electrolyte becomes equal, perpetual operation of SLRFB is expected. The identification of strong role of free convection in battery is put to use to demonstrate a battery that requires stirring/mixing only intermittently, during open circuit stages between charge and discharge cycles when no current is drawn. Inspired by our experimental finding that the measured currents for apparently diffusion limited situations (no external flow) are far larger than the maxi-mum possible theoretical value, the earlier model is modified to account for natural convection driven by concentration gradient of lead ions in electrolyte. The model reveals the presence of strong natural convection in battery. The induced flow in the vicinity of the electrodes enhances mass transport rates substantially, to the extent that even in the absence of external flow, normal charge/discharge of battery is predicted. The model predicted electrochemical characteristics are verified quantitatively through voltage-time measurements. The formation of flow circulation loops driven by electrode processes is validated qualitatively through PIV measurements. Natural convection is predicted to play a significant role in the presence of external flow as well. The hitherto unexplained finding in the literature on insensitivity of charge-discharge characteristics to electrolyte flow rate is captured by the model when mixed mode of convection is invoked. Flow reversal and wavy flow are predicted when natural convection and forced convection act in opposite directions in the battery. The effect of the presence of non-conducting material (PbO on anode) on the performance of SLRFB is studied using a simplified approach in the model. The study reveals the presence of charge coup de fouet phenomenon in charge cycle. The phenomenon as well as the predicted effect of depth of discharge on the magnitude of charge coup de fouet are confirmed experimentally.

[ES] Un aumento de la generación de energía a partir de fuentes renovables (solar, eólica) requiere una alta flexibilidad de las redes eléctricas. En este sentido, las baterías de flujo redox de vanadio (BFRV) han demostrado una excelente capacidad para proporcionar dicha flexibilidad, mediante el almacenamiento eficiente de energía eléctrica en el rango de los kWh a los MWh. Sin embargo, sus elevados costes son en la actualidad unos de los mayores inconvenientes que dificultan una amplia penetración en el mercado. En la presente Tesis Doctoral se presenta el desarrollo y evaluación de una celda tubular especialmente diseñada con una membrana de 5.0mm. Las células tubulares así diseñadas deberían alcanzar una mayor densidad de potencia (kWm^(-3)). Del mismo modo, la sustitución de uno de los electrodos por un electrodo bifuncional de aire debería de incrementar la energía específica de dicha celda (Whkg^(-1)) y reducir, por tanto, los costes energéticos asociados (€/kWh). El diseño de la celda desarrollado en la presente Tesis Doctoral facilita la fabricación de los colectores y membranas actuales con el empleo de procesos de extrusión y marca un paso importante hacia la fabricación rentable de semiceldas y celdas completas en el futuro. Para evaluar el comportamiento de la nueva celda diseñada se han llevado a cabo estudios de polarización, de espectroscopia de impedancia, y medidas de ciclos de carga/descarga. Las celdas desarrolladas presentan una corriente de descarga máxima de 89.7mAcm^(-2) y una densidad de potencia de 179.2kW/m^3. Además, los bajos sobrepotenciales residuales obtenidos en los electrodos de la celda resultan prometedores. No obstante, la resistencia del área específica de celda de 3.2 ohm*cm² impone limitaciones significativas en la densidad de corriente. Eficiencias Coulomb del 95 % han sido obtenidas, comparables a los valores alcanzados en celdas planas de referencia. Sin embargo, las pérdidas óhmicas resultan elevadas, reduciendo la eficiencia energética del sistema al 56 %. Las celdas tubulares fabricadas con un electrodo de difusión de gas de una sola capa con Pt/IrO2 como catalizador permiten alcanzar densidades de corriente máximas de 32mAcm^(-2) (Ecell =2.1 V/0.56V Ch/Dch). Los elevados sobrepotenciales de activación y el reducido voltaje en circuito abierto (debido a potenciales mixtos) conducen a una densidad de potencia comparativamente baja de 15.4mW/ cm². El paso de iones de vanadio a través de la membrana se considera uno de los grandes inconvenientes en este tipo de celdas tubulares, lo que lleva a que la densidad de energía real de 23.2Wh l^(-1) caiga por debajo del valor nominal de 63.9Wh l^(-1). / [CA] Un augment de la generació d'energia a partir de fonts renovables (solar, eòlica) requereix una alta flexibilitat de les xarxes elèctriques. En aquest sentit, les bateries de flux redox de vanadi (VRFB) han demostrat una excel·lent capacitat per a proporcionar aquesta flexibilitat, mitjançant l'emmagatzematge eficient d'energia elèctrica en el rang dels kWh als MWh. En la present Tesi Doctoral es presenta el desenvolupament i avaluació d'una cel·la tubular especialment dissenyada amb una membrana de 5.0mm. Les cèl·lules tubulars així dissenyades haurien assolir una major densitat de potència (kWm^(-3)). De la mateixa manera, la substitució d'un dels elèctrodes per un elèctrode bifuncional d'aire hauria d'incrementar l'energia específica d'aquesta cel·la (Whkg^(-1)) i reduir, per tant, els costos energètics associats (€/kWh). El disseny de la cel·la desenvolupat en la present tesi doctoral facilita la fabricació dels col·lectors i membranes actuals amb l'ocupació de processos d'extrusió i marca un pas important cap a la fabricació rendible de semiceldas i cel·les completes en el futur. Per avaluar el comportament de la nova cel·la dissenyada s'han dut a terme estudis de polarització, d'espectroscòpia d'impedància, i mesures de cicles de càrrega/ descàrrega. Les cel·les desenvolupades presenten un corrent de descàrrega màxima de 89.7mAcm^(-2) i una densitat de potència de 179.2kW/m^3. A més, els baixos sobrepotencials residuals obtinguts en els elèctrodes de la cel·la resulten prometedors. No obstant això, la resistència de l'àrea específica de cel·la de 3.2 ohm*cm² imposa limitacions significatives en la densitat de corrent. Eficiències Coulomb del 95 % han estat obtingudes, comparables als valors assolits en cel·les planes de referència. No obstant això, les pèrdues òhmiques resulten elevades, reduint l'eficiència energètica del sistema al 56 %. Les cel·les tubulars fabricades amb un elèctrode de difusió de gas d'una sola capa amb Pt/IrO2 com a catalitzador permeten assolir densitats de corrent màximes de 32mAcm^(-2) (Ecell =2.1 V/0.56V Ch/Dch). Els elevats sobrepotencials d'activació i el reduït voltatge en circuit obert (a causa de potencials mixtes) condueixen a una densitat de potència comparativament baixa de 15.4mW/ cm². El pas de ions de vanadi a través de la membrana es considera un dels grans inconvenients en aquest tipus de cel·les tubulars, el que porta al fet que la densitat d'energia real de23.2Wh l^(-1) caigui per sota del valor nominal de 63.9Wh l^(-1). / [EN] An increase of the power generation from volatile renewable sources (solar, wind) requires a high flexibility in power grids. All Vanadium Redox Flow Batteries (VRFBs) have demonstrated their ability to provide flexibility by storing electrical energy on a kWh to MWh scale. High power and energy specific costs do, however prevent a wide market penetration. In this dissertation a tubular cell design with a membrane diameter of 5.0mm is developed and evaluated. Tubular VRFB cells shall lead to an enhanced power den- sity (kWm^(-3)). Replacement of an electrode with a bifunctional air electrode (Vanadium/ Air Redox Flow Battery) shall allow to increase the specific energy (Whkg^(-1)) and reduce energy specific costs (€/kWh). The developed design facilitates a fabrication of the current collectors and membrane by an extrusion process and marks an important step towards the cost-efficient ex- trusion of entire half cells and cells in the future. To evaluate the cell performance and investigate loss mechanisms, polarization curve, electrochemical impedance spectroscopy and charge/discharge cycling measurements are conducted. Tubular VRFB cells with flow-by electrodes reveal a maximum dis- charge current and power density of 89.7mAcm^(-2) and 179.2kW/m^3, respectively. Low residual overpotentials at the cell's electrodes are encouraging, but the area spe- cific cell resistance of 3.2 ohm*cm² imposes limitations on the current density. Coulomb efficiencies of 95% are comparable to values of planar reference cells, but high ohmic losses reduce the system energy efficiency to 56 %. Tubular VARFB cells with a mono-layered gas diffusion electrode and a Pt/IrO2 catalyst allow for a maximum current density of 32mAcm^(-2) (Ecell =2.1 V/0.56V Ch/Dch). High activation overpotentials and a reduced open-circuit voltage (due to mixed potentials) lead to a comparably low power density of 15.4mW/ cm². Cross- over of vanadium ions through the membrane are considered as a major drawback for tubular VARFB cells and the actual energy density of 23.2Wh l^(-1) falls below the nominal value of Wh l^(-1). / Financial support of my research activities was provided by the BMBF through the common research project tubulAir±. / Ressel, SP. (2019). Tubular All Vanadium and Vanadium/Air Redox Flow Cells [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/131203

Symmetric nonaqueous redox flow batteries (RFBs) use negative and positive battery solutions of the same solution composition to operate at high cell voltages. This research effort targets these systems since they offer performance improvements derived from using nonaqueous systems and symmetric active species. Nonaqueous solutions permit significantly higher cell voltages than state-of-the-art aqueous RFBs and symmetric active species chemistries reduce the required complexity of cell reactors. Both performance advantages correspond to significant cost improvements beyond already commercially competitive aqueous RFB chemistries. This document focuses on two classes of symmetric nonaqueous RFB chemistries: coordination complexes such as vanadium acetylacetonate [V(acac)₃] or chromium acetylacetonate [Cr(acac)₃], and organic active species such as 9,10-diphenylanthracene (DPA). V(acac)₃ delivers reversible electrochemistry that supports a 2.2 V equilibrium cell potential, but there are some gaps in the understanding of its degradation mechanisms. Cr(acac)₃ supports redox reactions that suggest cell potentials above 4 V, but shows signs of irreversibility in voltammetry experiments and is not yet well understood. Finally, the DPA system could be interesting because it does not use metal active species, and its voltammetry promises cell potentials above 3 V. Yet DPA suffers from low solubility in nonaqueous solvents that limit its practicality. These three systems show promise for symmetric nonaqueous RFBs and offer avenues for further improvement. Voltammetry and spectroelectrochemical electrolysis experiments on the metal coordination complexes clarify the mechanisms behind the voltammetry on these symmetric chemistries. Ligand dissociation causes the irreversible behavior observed in voltammetry on Cr(acac)₃. The same experiments reaffirm the expected cyclability of V(acac)₃. Chemical functionalization of the DPA center is performed to investigate the solubility and reactivity of various derivatives. Functionalizing DPA with ethylene glycol chains to form 'DdPA' significantly increases solubility limits from 0.6 mM and 44 mM for DPA in acetonitrile and 1,2-dimethoxyethane, respectively, to 12 mM and 0.21 M for DdPA in the same solvents. At the same time, DdPA retains redox activity that promises 3 V cell potentials. Ultimately, a custom, nonaqueous-compatible redox flow reactor was designed and used to test the performance of V(acac)₃, DPA, and DdPA under various operating conditions. Contradicting previous reports, V(acac)₃ delivers stable cycling over the 21- cycle experimental protocol. Exploration over a range of flow rates and current densities give energy and power densities up to 1.09 WhL^-1 and 0.16 Wcm^-2, respectively, for the battery solution compositions examined. These experiments further predict values up to 28 WhL^-1 and at least 0.22 Wcm^-2 for optimized V(acac)₃ battery solutions. DPA and DdPA deliver the highest operating potential observed from organic nonaqueous RFBs, discharging at 3 V and 2.9 V, but require further work to understand degradation in the systems.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第22842号 / 工博第4782号 / 新制||工||1748(附属図書館) / 京都大学大学院工学研究科電気工学専攻 / (主査)教授 引原 隆士, 教授 土居 伸二, 教授 木本 恒暢 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

No description available.