Page 190 was not included in the thesis. / <p> A research program is presented for assessing the plastic collapse load and shake-down load of reinforced concrete continuous beams. This investigation attempts to establish a range of validity of simple plastic theory when applied to the under-reinforced concrete beams and to determine the sensitivity of such structures to variable repeated loading. In attempt for more accurate prediction of the behaviour of reinforced concrete beams when subjected to variable repeated loading, the numerical beam analysis was developed.</p> <p> An experimental program was conducted on 10 reinforced concrete continuous beams. Deflections and strains of these specimens of nearly prototype size were measured and compared with predicted values at critical cross-sections. Resulting conclusions and recommendations for further research are made.</p> / Thesis / Master of Engineering (MEngr)

Thesis. (M.Tech. (Dept. of Civil Engineering and Building, Faculty of Engineering and Technology)) -- Vaal University of Technology, 2011. / This research focused on the structural performance of Fibre Reinforced Polymer (FRP) re-bars in structural foundation compared to steel reinforcement re-bars. The corrosion of steel re-bars is the main reason of deterioration of reinforced concrete. However, use of FRP re-bars as alternative reinforcement will address the deterioration of reinforced concrete. Carbon and Glass Fibre Reinforced Polymer re-bars were used as reinforcing bars and traditional steel reinforced concrete was used as the reference. Thirty six specimens of reinforced concrete bases were tested for flexural capacity at different ages. The simulation of Soil Bearing Pressure of this study was derived from the model of beam finite length on elastic foundation. The foundation base was treated as a beam while the soil was modelled as series of timber elements acting as springs. The mathematical model to reflect the model was as documented by Timoshenko (1976:18) and Den Hartog (1952:160). Results showed that stress in the steel re-bars of reinforced concrete was higher than that of Carbon Fibre Reinforced Polymer (CFRP) and Glass Fibre Reinforced Polymer (GFRP) re-bars by 227 MPa (5.99 percent) and 284 MPa (7.61 percent), respectively. The stress in CFRP re-bars was 57 MPa or 1.53 percent higher compared to GFRP re-bars of FRP reinforced concrete. Furthermore, the experimental ultimate moments of CFRP and GFRP reinforced concrete foundation – bases on the 28th day were 23.917 kNm (79.0 percent) and 23.529 kNm (77.7 percent) higher than the theoretical ultimate moments, respectively. However, steel reinforced concrete foundation – bases had the higher calculated deflection than FRP reinforced concrete. With high resistance to corrosion as a property, FRP re-bars appeared to be a better alternative reinforcement to steel in corrosion in an aggressive environment. / Vaal University of Technology

A thesis submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in fulfilment of the requirements for the degree of Doctor of Philosophy, Johannesburg, 2017 / Many reinforced concrete (RC) structures in inland environment deteriorate early due to carbonation-induced corrosion of their reinforcement. In some cases, the deterioration is visible within a few years of construction in the form of cover concrete cracking. This is widely accepted as one of the limit state indicators in defining the end of functional service life for existing RC structures undergoing corrosion. Many of the currently available service life prediction models are incapable of providing realistic service life estimates of RC structures beyond the corrosion initiation stage. Therefore, the need to incorporate the corrosion initiation and propagation stages in a comprehensive durability prediction approach has been receiving much research attention. In this research, empirical models were developed for predicting carbonation rate and the amount of steel radius loss required to initiate a first visible crack in concretes exposed to Johannesburg environment. The experimental data for the models were obtained from investigations of carbonation-induced reinforcement corrosion, which were explored in three phases; (i) concrete early-age durability and strength characteristics (ii) carbonation rate of different concrete mixes exposed to the natural inland environment (iii) amount of steel radius loss required to initiate the first visible crack on the pre-carbonated cover concretes exposed to an unsheltered environment. The experimental variables for the earlyage durability and strength tests were; water/binder ratio (w/b) and binder type; w/b, binder type, initial moist curing duration and exposure conditions are the experimental variables for the carbonation rate test. Cover depth, reinforcement diameter, binder type and w/b variables were considered for the corrosion cracking test. The results showed that an improvement in concrete quality (binder type, w/b ratio and extending the initial moist curing duration) and increment in cover thickness improved the durability of the RC structures exposed to the natural inland environment. Based on the trends in the observed experimental results, models to predict carbonation rate and the amount of steel radius loss required to initiate cover cracking in concrete were developed. The proposed models’ predictions are more closer to the measured values and compared well with the predictions of some previous models which indicate their respective predictive applications. They provide a general basis for durability analysis of RC structures in inland environment and can serve as basis for condition assessment of existing structures in the inland environment. Engineers can appreciate the consequences of design options on the service life of RC structures, while owners of RC structures can have information about how long their RC structures may last before any repair is envisaged / XL2018

The FDOT has been using supplementary cementitious materials while constructing steel reinforced concrete marine bridge structures for over 3 decades. Previous findings indicated that such additions in concrete mix makes the concrete more durable. To better understand corrosion propagation of rebar in high performance concrete: mature concrete samples that were made (2008/2009) with Portland cement, a binary mix, a ternary mix and recently prepared (April 2016 with 50% OPC + 50% slag and 80% OPC + 20% Fly ash) concrete samples were considered. None of these concretes had any admixed chloride to start with. An accelerated chloride transport process was used to drive chloride ions into the concrete so that chlorides reach and exceed thechloride threshold at the rebar surface and initiate corrosion. Electrochemical measurements were taken at regular intervals (during and after the electro-migration process) to observe the corrosion propagation in each sample. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2017. / FAU Electronic Theses and Dissertations Collection

published_or_final_version / Civil Engineering / Master / Master of Philosophy

Thesis (Ph.D.)--University of Adelaide, Dept. of Civil and Environmental Engineering, 2002. / Includes corrigenda (inserted at front) and list of publications published as a result of this research. Includes bibliographical references (leaves 192-199).

In order to study the mechanical performance of dry-cast synthetic fiber reinforced concrete (SynFRC), samples of varying geometry, fiber content, and environmental exposure were developed and tested using the modified indirect tensile test. The samples created consisted of three different thicknesses (with two different geometries), and six different fiber contents that differed in either type, or quantity, of fibers. Throughout the duration of this research, procedures for inflicting detrimental materials into the concrete samples were employed at a number of different environments by implementing accelerated rates of deterioration using geometric adjustments, increased temperature exposure, wetting/drying cycles, and preparation techniques. The SynFRC samples studied were immersed in a wide range of environments including: the exposure of samples to high humidity and calcium hydroxide environments, which served at the control group, while the sea water, low pH, and barge conditioning environments were used to depict the real world environments similar to what would be experienced in the Florida ecosystem. As a result of this conditioning regime, the concrete was able to imitate the real-world effects that the environments would have inflicted if exposed for long durations after an exposure period of only 20-24 months. Having adequately conditioned the samples in their respective environments, they were then tested (and forensically investigated) using the modified indirect tensile testing method to gather data regarding each sample’s toughness and load handling capability. By analyzing the results from each sample, the toughness was calculated by taking the area under the force displacement curve. From these toughness readings it was found that possible degradation occurred between the fiber-matrix interface of some of the concrete samples conditioned in the Barge environment. From these specimens that were immersed in the barge environment, a handful of them exhibited multiple episodes of strain softening characteristics within their force displacement curves. In regard to the fibers used within the samples, the PVA fibers tended to pull off more while the Tuff Strand SF fibers had the highest tendency to break (despite some of the fibers showing similar pull off and breaking failure characteristics). When it comes to the overall thickness of the sample, there was clear correlation between the increase in size and the increase in sample toughness, however the degree to which it correlates varies from sample to sample. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2020. / FAU Electronic Theses and Dissertations Collection

Highway drainage pipes utilize concrete reinforced with steel wire to help mitigate water, earth, and traffic loads. Drainage pipes reinforced with zinc electroplated steel fibers offer a lower steel alternative to traditional steel wire cage reinforcements. The objective of the thesis research was to determine the physical and electrochemical characteristics of zinc electroplated steel fiber corrosion propagation. Experimental programs include: Fracture analysis of zinc electroplated steel fibers embedded in dry-cast concrete pipes exposed to varying chloride concentrations; Visual analysis of zinc electroplated steel fibers embedded in concrete exposed to varying chloride concentrations; Electrochemical analysis of zinc electroplated steel fibers embedded in concrete exposed to varying chlorides; Chloride threshold determination for zinc electroplated steel fibers immersed in simulated pore solution. Between the four experimental programs the most significant conclusion is that oxygen, moisture, and chlorides past the chloride threshold must be present for corrosion to propagate significantly on the zinc electroplated steel fibers. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2016. / FAU Electronic Theses and Dissertations Collection

De nos jours, le béton est le matériau de construction le plus utilisé dans le monde en raison de ses performances mécaniques, sa facilité de mise en oeuvre, son coût compétitif et sa « recyclabilité ». Toutefois, compte tenu de son caractère fragile en terme mécanique et de sa faible résistance à la traction, il est souvent renforcé par des armatures métalliques qui lui confèrent une bonne ténacité et une meilleure aptitude à supporter les efforts de traction. Ce composite béton-armature ne peut cependant assurer efficacement son rôle que si les deux composants sont étroitement liés l’un à l’autre. C’est donc dans la qualité de l’adhérence que réside l’efficacité du transfert des efforts entre les deux matériaux. Or, dès la mise en place des ouvrages en béton armé et pendant toute la durée de leur exploitation, différentes actions et agents agresseurs peuvent modifier la qualité de cette adhérence. Il peut s’agir de phénomènes naturels comme le gel/dégel et l’action du dioxyde de carbone atmosphérique, ou des sollicitations accidentelles comme l’incendie ou encore l’action de certains agents spécifiques comme les chlorures et les sulfates. Notre objectif dans cette thèse est de qualifier les modifications d’adhérence qui résultent de quatre types de sollicitations couramment rencontrées dans la vie des ouvrages en béton armé: l’effet des températures élevées, l’effet de la carbonatation, l’effet des cycles gel/dégel, l’effet de la corrosion. Nous évaluons la qualité de l’adhérence par la mesure de la résistance à l’arrachement et par l’analyse du comportement résiduel sous sollicitation mécanique. La technique d’émission acoustique est utilisée pour localiser en temps réel, l’endommagement du matériau sous sollicitation. Les applications de notre étude concernent non seulement les armatures et inserts classiques du béton armé mais aussi les nombreux dispositifs constructifs des structures mixtes acier – béton qui utilisent les liaisons par goujons pour relier les deux matériaux. / Nowadays, concrete is the most used construction material in the world because of its mechanical performances, its ability to be molded or cast, its competitive cost and its recyclability. However, concrete has a low ductility and a relatively low tensile strength compared to other construction materials. Therefore, concrete is often reinforced by steel rebars to improve the ductility and tensile strength. Nevertheless, to make reinforced concrete being highly efficient material, the two components need to be correctly bonded each to other. The bond quality the efficiency of the force transfer between rebar and concrete surrounding ensures. In fact, since the casting of concrete and during the service life of reinforced concrete structure, various actions such corrosion action, freeze/thaw attack and chemical attack etc. may affect the bond quality. The objective of this PhD research work is to qualify the changes of adhesion property causing by four types of action which frequently takes place in the service life of reinforced concrete structures: the effect of high temperatures, the effect of carbonation, the effect of cycles freeze/thaw, the effect of corrosion. The concrete-rebar bond quality is evaluated by doing pull-out tests under static mechanical action and measuring the bond strength and analyzing residual behaviour. Moreover, the acoustic emission technique is used to locate the cracks and evaluate the cracking evolution in real time. The founding of this study can be also extended to apply to other concrete-steel structures like composite structures in which headed studs are used to connect steel profiles to concrete.

published_or_final_version / Civil Engineering / Doctoral / Doctor of Philosophy