Much previous experimentation related to wood structures has employed monotonic loading to replicate static situations. However, instances of natural hazards have raised interest in the response of structural connections to dynamic loads. This increased interest led the Consortium of Universities for Research in Earthquake Engineering (CUREE) to develop a testing protocol for reverse-cyclic loading, which involves cycling loads through zero in order to test specimens in both tension and compression. With the CUREE testing protocol in place, recent research has been devoted to understanding the effects of reverse-cyclic loading on multiple-fastener connections. Experimentation by Heine (2001), Anderson (2002), Billings (2004) and others contributed to a better understanding of bolted connection behavior under reverse-cyclic loading. However, some questions remained. Billings was unable to consistently produce yield modes III and IV, meaning that her suggested bolt spacing of seven times the bolt diameter (7D) could not be applied to connections subject to these yield modes without further testing. In addition, the work of Anderson and Billings raised questions regarding the proper measurement of bending yield strength in bolts and the relationship between the bending yield strength and the tensile yield strength. These topics are each addressed by this project and thesis report. Results of the connection testing presented in this report can be used in conjunction with the work of Anderson and Billings to critically evaluate the 4D between-bolt spacing recommended by the National Design Specification (NDS) for Wood Construction (AF&PA, 2001). Results of the bolt testing provide a supplement to the search for a reliable method for the measurement of bending yield strength in bolts. / Master of Science

Concrete is a very weak and brittle material in tension. It has been shown in previous researches that the addition of steel fibers to a concrete matrix can improve this behavior. The ability of fibers to control and redistribute stresses after cracking results in a number of improvements in the structural behaviour of concrete. A review of existing literature shows that the addition of steel fibers enhances concrete’s tensile resistance, crack control properties, ductility and damage tolerance. In beams, fibers can transform brittle shear response into a flexural response and promote ductility, thereby allowing for a full or partial replacement of traditional shear reinforcement. The enhanced shear capacity, ductility and damage tolerance of Steel Fiber Reinforced Concrete (SFRC) can also potentially be used to relax seismic detailing requirements in frames by partially replacing the required transverse reinforcement in the plastic hinge regions of RC beams. One of the drawbacks associated with SFRC is that the addition of steel fibers to a traditional concrete mix at high fiber contents can result in workability problems. The combined use of Self-Consolidating Concrete (SCC) and fibers can solve this problem and facilitate placement for a wider range of structural applications. Although several studies have been conducted on the behaviour of SFRC beams subjected to monotonic loading, there is limited research on the behaviour of SFRC beams under cyclic or reverse-cyclic loading. This thesis presents the results of an experimental and analytical study conducted on nine SFRC beam specimens tested under load reversals. The main objective of this research program was to investigate the effect of fibers on structural behaviour and to examine the ability of steel fibers to replace transverse reinforcement. The experimental and analytical results show that use of fibers results in several improvements in behaviour, including enhanced damage tolerance and post-peak ductility. The results also show that steel fibers can potentially be used to allow for a reduction of transverse reinforcement in beams, however further research is required.

Concrete is a very weak and brittle material in tension. It has been shown in previous researches that the addition of steel fibers to a concrete matrix can improve this behavior. The ability of fibers to control and redistribute stresses after cracking results in a number of improvements in the structural behaviour of concrete. A review of existing literature shows that the addition of steel fibers enhances concrete’s tensile resistance, crack control properties, ductility and damage tolerance. In beams, fibers can transform brittle shear response into a flexural response and promote ductility, thereby allowing for a full or partial replacement of traditional shear reinforcement. The enhanced shear capacity, ductility and damage tolerance of Steel Fiber Reinforced Concrete (SFRC) can also potentially be used to relax seismic detailing requirements in frames by partially replacing the required transverse reinforcement in the plastic hinge regions of RC beams. One of the drawbacks associated with SFRC is that the addition of steel fibers to a traditional concrete mix at high fiber contents can result in workability problems. The combined use of Self-Consolidating Concrete (SCC) and fibers can solve this problem and facilitate placement for a wider range of structural applications. Although several studies have been conducted on the behaviour of SFRC beams subjected to monotonic loading, there is limited research on the behaviour of SFRC beams under cyclic or reverse-cyclic loading. This thesis presents the results of an experimental and analytical study conducted on nine SFRC beam specimens tested under load reversals. The main objective of this research program was to investigate the effect of fibers on structural behaviour and to examine the ability of steel fibers to replace transverse reinforcement. The experimental and analytical results show that use of fibers results in several improvements in behaviour, including enhanced damage tolerance and post-peak ductility. The results also show that steel fibers can potentially be used to allow for a reduction of transverse reinforcement in beams, however further research is required.

Concrete is a very weak and brittle material in tension. It has been shown in previous researches that the addition of steel fibers to a concrete matrix can improve this behavior. The ability of fibers to control and redistribute stresses after cracking results in a number of improvements in the structural behaviour of concrete. A review of existing literature shows that the addition of steel fibers enhances concrete’s tensile resistance, crack control properties, ductility and damage tolerance. In beams, fibers can transform brittle shear response into a flexural response and promote ductility, thereby allowing for a full or partial replacement of traditional shear reinforcement. The enhanced shear capacity, ductility and damage tolerance of Steel Fiber Reinforced Concrete (SFRC) can also potentially be used to relax seismic detailing requirements in frames by partially replacing the required transverse reinforcement in the plastic hinge regions of RC beams. One of the drawbacks associated with SFRC is that the addition of steel fibers to a traditional concrete mix at high fiber contents can result in workability problems. The combined use of Self-Consolidating Concrete (SCC) and fibers can solve this problem and facilitate placement for a wider range of structural applications. Although several studies have been conducted on the behaviour of SFRC beams subjected to monotonic loading, there is limited research on the behaviour of SFRC beams under cyclic or reverse-cyclic loading. This thesis presents the results of an experimental and analytical study conducted on nine SFRC beam specimens tested under load reversals. The main objective of this research program was to investigate the effect of fibers on structural behaviour and to examine the ability of steel fibers to replace transverse reinforcement. The experimental and analytical results show that use of fibers results in several improvements in behaviour, including enhanced damage tolerance and post-peak ductility. The results also show that steel fibers can potentially be used to allow for a reduction of transverse reinforcement in beams, however further research is required.

This thesis presents the results of testing to determine if spacing between bolts in a multiple-bolt, single-shear connection subjected to natural hazard loading affects seven strength and serviceability parameters: maximum load, failure load, E.E.P. yield load, 5% offset load, elastic stiffness, E.E.P. energy, and ductility ratio. This research also determines if a statistical difference exists between previously published research for 4D spacing as compared to results produced by this research for five alternate spacings: 8D, 7D, 6D, 5D, and 3D. Finally, this research determines which of the spacings examined: 8D, 7D, 6D, 5D, 3D; produced the most optimal results for each examined strength and serviceability parameter where optimization is based on economy and performance. Three connection configurations with five different spacings between bolts were subjected to reverse cyclic loading for a total of one hundred and fifty tests. The reverse cyclic protocol was based on recommendations by the Consortium of Universities for Research in Earthquake Engineering (CUREE) for testing woodframe structures. The same connection configurations were also subjected to monotonic loading for an additional forty-five tests. Results of this research can be used to evaluate the current design recommendation presented in the National Design Specification (NDS) for Wood Construction (AF&PA, 2001) of spacing bolts at four times the bolt diameter (4D) to determine if a different spacing should be recommended for natural hazard loading conditions. / Master of Science