Hydro power plants are an essential part of the infrastructure in Sweden as they stand for a large amount of the produced electricity and are used to regulate supply and demand on the electricity grid. Other renewable energy sources, such as wind and solar power, have become more popular as they contribute to a fossil free society. However, wind and solar power are intermittent energy sources causing the demand for regulating power on the grid to increase. Hydro power turbines are designed to operate at a certain design point with a specific flow rate. The plants are operated away from the design point when used to regulate the supply and demand of electricity. This can cause a specific flow phenomenon to arise in the draft tube at part load conditions called a Rotating Vortex Rope (RVR) which causes dangerous pressure fluctuation able to damage blades and bearings. A solution to mitigate a RVR is to inject pulsating momentum into the draft tube by using an actuator operating at a certain frequency. A literature study was conducted and three techniques were numerically simulated using ANSYS Workbench 19.0 R3; a fluidic oscillator, a piston actuator and a synthetic jet actuator. A dynamic mesh was used to simulate the movement of the piston actuator and diaphragm of the synthetic actuator whilst the mesh of the fluidic oscillator was stationary. The relative errors of the three numerical models were all below 3 %. All devices showed promising results and could potentially be used to mitigate a RVR because they all have the ability to produce high energy jets. The fluidic oscillator had an external supply of water, whereas the other two did not, which means that it could inject the largest mass flow. The piston actuator required a driving motor to move the piston. The diaphragm of the synthetic jet actuator was moved by a Piezoelectric element. Advantages of the fluidic oscillator are that it has no moving parts, in contrary to the two other devices, it can directly be connected to the penstock or draft tube to obtain the required water supply and it is easy to install. It will most likely also be smaller compared to the other two for the same mass flow rate. It does however not generate a pulsating jet, but rather an oscillating jet. The other two devices generate pulsating jets, but have problems with low pressure areas during the intake stroke which can cause cavitation problems. These areas cause the formation of vortex rings close to the outlet. Simulations showed that a coned piston together with a coned cylinder outlet could decrease losses by almost 16 % compared to a normal piston and cylinder. It also decreased the risk for cavitation and the required force to move the piston. Otherwise, a shorter stroke length for a constant cylinder diameter or a longer stroke length for a constant volume displacement also decreased the risk for cavitation and required force. The gasket between the piston and cylinder is a potential risk for leakage. A solution to avoid critical low pressure areas is to install an auxiliary fluid inlet or valve which opens at a certain pressure for the piston actuator as well as the synthetic jet actuator. This will also allow larger mass flow rates and a higher injected momentum. Both devices are more complicated to install and require likely more maintenance compared to the fluidic oscillator. However, there exist many possible design options for the piston actuator. The design of the synthetic jet is more limited because of the diaphragm. The amplitude of the diaphragm also has a direct effect on the pressure levels. The losses increased proportional to the mass flow to the power of three which suggests that it is better to install many small actuators instead of a few large ones.

The use of renewable energy such as water and wind to produce electricity has been proven extremely effective in Sweden. The ability of these renewable resources to produce clean output energy counters the adversities caused by non-renewable resources. The use of hydraulic turbines is a good example of favoured technique for energy and power production using renewable resources. The hydro-turbines are designed to operate at best efficiency point (BEP). Varying energy demands in recent years implies on the need of flexible operation of hydraulic turbines. The issue of pressure pulsations in the draft tube of hydro-turbines, observed at lower operating conditions has been unresolved for many years. These pressure pulsations are related to the ‘rotating vortex rope’ (RVR) observed at part load operation and, affects the lifespan and performance of the hydro-turbine adversely. Several techniques have been investigated in the past to reduce the pressure pulsations in the draft tube at part load operation and enhance the flexibility of the turbine. During the present research study, a passive flow control technique was investigated numerically by implementing a guide vane system in the draft tube of the Francis-99model turbine. Guide vanes are mechanical devices that can direct the flow in a desired direction. The current study presents the possibility of reducing the pressure pulsations in the draft tube by mitigating the RVR using a guide vane system in the draft tube. At the initial stages of the research study, a reduced numerical model of the Francis model turbine was developed by only considering the draft tube domain. The motive was to develop a reduced model to perform the parametric analysis for the guide vane system in the draft tube with reduced computational time, power, and storage. The results obtained from the numerical study were found to be in good agreement with theFrancis-99 semi-model with passage domains. A parametric study was performed to achieve a guide vane system design that could mitigate RVR with minimum losses. During this study, the number of guide vanes, the chord and the span of the guide vanes were investigated. It was found that a set of three guide vane system with chord of 86% of runner radius and leading-edge span of 30% of runner radius is an ideal design that mitigates RVR above 95%.