Thesis (Ph. D.)--Virginia Polytechnic Institute and State University, 1992. / Vita. Abstract. Includes bibliographical references (leaves 67-71). Also available via the Internet.

Thesis (M.S.)--California Polytechnic State University, 2009. / Title from PDF title page; viewed on Nov. 16, 2009. "September 2009." "In partial fulfillment of the requirements for the degree [of] Master of Science in Aerospace Engineering." "Presented to the faculty of California Polytechnic State University, San Luis Obispo." Major professor: David D. Marshall, Ph.D. Includes bibliographical references (p. 85-87).

No description available.

As the flight speeds of aircraft are increased above Mach 5, efficient methods of propulsion are needed. Scramjets may be a solution to this problem. Supersonic combustion is one of the main challenges involved in the operation of a Scramjet engine. In general, both an igniter and a flameholder are needed to achieve and maintain supersonic combustion. The current work examines a plasma torch-strut combination as an igniter-flameholder. The plasma torch-strut combination was tested in the Virginia Tech unheated supersonic wind tunnel at Mach 2.4. Pressure and temperature sampling, filtered photography, and spectroscopic measurements were used to compare different test cases. These results provide both qualitative and quantitative results on how the combination responds to changes in the mass flow rate of fuel and the power to the plasma torch. The key conclusions of the work were the following: 1. Tests showed that an exothermic reaction takes place. 2. The amount of heat release increases with an increase in the mass flow rate of fuel. 3. The plasma torch-fuel injector interaction caused the heat release to be well above the tunnel floor and sometimes off the strut centerline 4. One change in the fuel injector pattern caused more temperature rise near the floor of the tunnel. 5. The flow penetration height of the plasma torch alone was reduced by the fuel-plasma torch interaction. 6. Moving the strut upstream reduced the measured temperature rise at a fixed downstream location, but increased the penetration height of the plasma torch. 7. The computed heat release was found to be small compared to the potential heat release from all the fuel burning. 8. The amount of temperature rise caused by the fuel is not greatly affected by the power to the plasma torch. / Master of Science

To realize supersonic combustion of hydrocarbons, an effective atomizer-igniter combination with the capabilities of fuel preheating, atomization, penetration, mixing, ignition and flameholding is desired. An original design concept incorporating these capabilities was built and tested at Virginia Tech, and was found to provide good penetration, effective atomization, and robust ignition and flameholding. Quiescent testing with kerosene and JP-7 provided initial performance data. The atomizer-injector design was then modified for insertion into a supersonic wind tunnel, and tested with kerosene in an unheated Mach 2.4 flow with typical freestream conditions of To = 280 K and Po = 360 kPa. Water injection was utilized in both cases for comparison and to analyze atomization behavior. In the quiescent environment, the regeneratively cooled plasma torch igniter was found to significantly increase electrode life while heating, atomizing, and igniting the liquid fuel. Jet breakup length was measured and characterized, and mean droplet size was estimated using an existing correlation. Several qualitative observations regarding quiescent combustion were made, including torch power effects and the process of flame formation. In the supersonic environment, the effect of fuel injection direction was analyzed. Best results were obtained when fuel was injected with a velocity component opposite to the direction of main tunnel flow. Repeatable ignition occurred in the supersonic boundary layer at the fuel stagnation location near the plasma torch plume. Direct, filtered, shadowgraph, and schlieren photographs, temperature measurements, and visible emission spectroscopy provided evidence of combustion and the details of the flame structure. The new atomizer-igniter design provided robust and reliable ignition and flameholding of liquid hydrocarbon fuels in an unheated supersonic flow at M=2.4, with no ramp, step, or other physical penetration into the flowpath. / Master of Science

No description available.

No description available.

No description available.

Rapid mixing and spreading of supersonic jets are two important characteristics in supersonic ejectors, noise reduction in jets and fuel mixing in supersonic combustion. It helps in changing the acoustic and thermal signature in supersonic exhaust. The supersonic nozzles in most cases result in compressible mixing layers. The subsonic nozzles form incompressible mixing layers but at high Mach numbers even they form compressible mixing layers. Compressible mixing layers have been found to have much lower mixing and spreading rates than incompressible mixing layer Birch & Eggers (1972). In order to enhance the spreading and mixing of mixing layers from supersonic nozzles various active and passive methods have been deviced. Active methods include fluid injection, fluid lobes and plasma actuation. Passive methods are mostly based on modifying the nozzle geometry such that the fluid expansion is ideal or the shock cell is broken. Many nozzles with exotic shapes have been developed to obtain mixing enhancements in supersonic jets Gutmark et al. (1995). To achieve enhanced mixing an innovative nozzle named as the Elliptic Sharp Tipped Shallow (ESTS) lobed nozzle has been developed in L.H.S.R., I.I.Sc., India Rao & Jagadeesh (2014). This nozzle has a unique geometry involving elliptical lobes and sharp tips. These lobes are generated using a simple manufacturing process from the throat to the exit. This lobed and sharp tipped structure introduces stream wise vortices and azimuthal velocity components which must help in enhanced mixing and spreading. The ESTS lobed nozzle has shown mixing enhancement with 4 lobes. The spreading rate was found to be double of the reference conical nozzle. This thesis is motivated by the need to investigate the flow physics involved in the ESTS lobed nozzle. The effect of varying the number of lobes and the design Mach number of the nozzle on the mixing and spreading characteristics will be further discussed. Visualisation studies have been performed. The schlieren and planar LASER Mie scattering techniques have been used to probe the flow. Instantaneous images were taken at axial planes with the reference conical and ESTS nozzles with three, four, five and six lobes. The nozzles are for design Mach number 2.0 and 2.5. The stagnation chamber pressure was maintained to obtain over expanded, ideally expanded and under expanded flows. LASER scattering was obtained by seeding the flow with water to observe the behaviour of the primary flow. The condensation of moisture due to the cold primary flow mixing with the ambient air was exploited to scatter laser and observe the flow structures in the mixing layer. A comparison of the images of the reference conical nozzle and the ESTS lobed nozzles shows changes in the mixing layers due to the ESTS lobed nozzles. The image of the reference conical nozzle shows a distinct potential core and mixing layers all along the length of the image. For the ESTS lobed nozzles this distinction becomes unclear shortly after the nozzle exit. Thus mixing of the primary flow and ambient air is seen to be enhanced in the case of all the ESTS lobed nozzles. The flow in the case of the ESTS lobed nozzles if found to be highly non axis symmetric. The starting process of the nozzles has been visualised using time resolved schlieren. Image processing was performed on the nozzles to quantify the spread rate. The shock structure of the nozzles has been studied and found to be modified due to the lobed geometry. The level of convolution of the mixing layer due to the lobed structure has been studied using fractal analysis. The four lobed nozzle was found to have the highest spread rate and th most convoluted shear layer. Hence this nozzle was further studied using background oriented schlieren and particle image velocimetry to quantify the flow field. These experimental results have been compared with CFD simulations using the commercial software CFX5. The computations and experiments don’t match accurately but the trends match. This allows for simulations to be used as a good first approximation. The acoustic properties of a jet are dependent on the flow structure behaviour. The ESTS lobes have been found to change the flow structure. Hence the ESTS lobed nozzle was predicted to change the acoustic signature of the flow. The acoustic measurements of the flow were carried out at National Aerospace Laboratories, Bengaluru. The screech of the overexpanded flow was seen to be eliminated and the overall sound levels were found to have been reduced in all cases. Thus the lobed nozzle was found to have acoustic benefits over the reference conical nozzle. Thus the ESTS lobed nozzle has been studied and compared with the conical nozzle using several methods. The changes due to the lobed structure have been studied quantitatively. Future studies would focus on the change in thrust due to the lobed structure. Also new geometries have been proposed inspired by the current design but with possible thrust benefits or manufacturing benefits.

abstract: The objective of this study is to understand how to integrate conical spike external compression inlets with high bypass turbofan engines for application on future supersonic airliners. Many performance problems arise when inlets are matched with engines as inlets come with a plethora of limitations and losses that greatly affect an engine’s ability to operate. These limitations and losses include drag due to inlet spillage, bleed ducts, and bypass doors, as well as the maximum and minimum values of mass flow ratio at each Mach number that define when an engine can no longer function. A collection of tools was developed that allow one to calculate the raw propulsion data of an engine, match the propulsion data with an inlet, calculate the aerodynamic data of an aircraft, and combine the propulsion and aerodynamic data to calculate the installed performance of the entire propulsion system. Several trade studies were performed that tested how changing specific design parameters of the engine affected propulsion performance. These engine trade studies proved that high bypass turbofan engines could be developed with external compression inlets and retain effective supersonic performance. Several engines of efficient fuel consumption and differing bypass ratios were developed through the engine trade studies and used with the aerodynamic data of the Concorde to test the aircraft performance of a supersonic airliner using these engines. It was found that none of the engines that were tested came close to matching the supersonic performance that the Concorde could achieve with its own turbojet engines. It is possible to speculate from the results several different reasons why these turbofan engines were unable to function effectively with the Concorde. These speculations show that more tests and trade studies need to be performed in order to determine if high bypass turbofan engines can be developed for effective usage with supersonic airliners in any possible way. / Dissertation/Thesis / Run file and text files from the propulsion simulations performed in NPSS. / Input and output file used in EDET to generate aerodynamic data of Concorde. / Five column propulsion data of tested engines after inlet matching. / Masters Thesis Aerospace Engineering 2018