Methods for conditional Poisson sampling (CP-sampling) and Sampford sampling are compared and the focus is on the efficiency of the methods. The efficiency is investigated by simulation in different sampling situations. It was of interest to compare methods since new methods for both CP-sampling and Sampford sampling were introduced by Bondesson, Traat & Lundqvist in 2004. The new methods are acceptance rejection methods that use the efficient Pareto sampling method. They are found to be very efficient and useful in all situations. The list sequential methods for both CP-sampling and Sampford sampling are other methods that are found to be efficient, especially if many samples are to be generated.

This thesis consists of five papers related to the theory of unequal probability sampling from a finite population. Generally, it is assumed that we wish to make modelassisted inference, i.e. the inclusion probability for each unit in the population is prescribed before the sample is selected. The sample is then selected using some random mechanism, the sampling design. Mostly, the thesis is focused on three particular unequal probability sampling designs, the conditional Poisson (CP-) design, the Sampford design, and the Pareto design. They have different advantages and drawbacks: The CP design is a maximum entropy design but it is difficult to determine sampling parameters which yield prescribed inclusion probabilities, the Sampford design yields prescribed inclusion probabilities but may be hard to sample from, and the Pareto design makes sample selection very easy but it is very difficult to determine sampling parameters which yield prescribed inclusion probabilities. These three designs are compared probabilistically, and found to be close to each other under certain conditions. In particular the Sampford and Pareto designs are probabilistically close to each other. Some effort is devoted to analytically adjusting the CP and Pareto designs so that they yield inclusion probabilities close to the prescribed ones. The result of the adjustments are in general very good. Some iterative procedures are suggested to improve the results even further. Further, balanced unequal probability sampling is considered. In this kind of sampling, samples are given a positive probability of selection only if they satisfy some balancing conditions. The balancing conditions are given by information from auxiliary variables. Most of the attention is devoted to a slightly less general but practically important case. Also in this case the inclusion probabilities are prescribed in advance, making the choice of sampling parameters important. A complication which arises in the context of choosing sampling parameters is that certain probability distributions need to be calculated, and exact calculation turns out to be practically impossible, except for very small cases. It is proposed that Markov Chain Monte Carlo (MCMC) methods are used for obtaining approximations to the relevant probability distributions, and also for sample selection. In general, MCMC methods for sample selection does not occur very frequently in the sampling literature today, making it a fairly novel idea.

The main objective in sampling is to select a sample from a population in order to estimate some unknown population parameter, usually a total or a mean of some interesting variable. When the units in the population do not have the same probability of being included in a sample, it is called unequal probability sampling. The inclusion probabilities are usually chosen to be proportional to some auxiliary variable that is known for all units in the population. When unequal probability sampling is applicable, it generally gives much better estimates than sampling with equal probabilities. This thesis consists of six papers that treat unequal probability sampling from a finite population of units. A random sample is selected according to some specified random mechanism called the sampling design. For unequal probability sampling there exist many different sampling designs. The choice of sampling design is important since it determines the properties of the estimator that is used. The main focus of this thesis is on evaluating and comparing different designs. Often it is preferable to select samples of a fixed size and hence the focus is on such designs. It is also important that a design has a simple and efficient implementation in order to be used in practice by statisticians. Some effort has been made to improve the implementation of some designs. In Paper II, two new implementations are presented for the Sampford design. In general a sampling design should also have a high level of randomization. A measure of the level of randomization is entropy. In Paper IV, eight designs are compared with respect to their entropy. A design called adjusted conditional Poisson has maximum entropy, but it is shown that several other designs are very close in terms of entropy. A specific situation called real time sampling is treated in Paper III, where a new design called correlated Poisson sampling is evaluated. In real time sampling the units pass the sampler one by one. Since each unit only passes once, the sampler must directly decide for each unit whether or not it should be sampled. The correlated Poisson design is shown to have much better properties than traditional methods such as Poisson sampling and systematic sampling.