No description available.

In the thesis are analysed influences of three shield gases, based on literary pursuit. Compared was influence of the gas consisting of pure Ar, mixture Ar with 3vol.% CO2 and the mixture Ar with 18vol.% CO2 on mechanical properties of conduction laser welded blunt welds made from structural steel DC01 and S235JR with thickness 3mm and 2mm. Compared were strength properties of the welds in tension, weld hardness and hardness of the heat affected area under the low stress. Further was observed and compared stream of the gases during welding process and its influences on the appearance of the trial welds. On the metallographical cuts of the welds were evaluated mistakes and dimensions of the welds.

No description available.

This paper focused on two significant space forces that can affect the success of a spacecraft: the radiation and micrometeoroid environments. Both are looked at in the context of the region of space between Earth and Mars. The goal was create reference environments, to provide context to results of environmental modeling, and to provide recommendations to assist in early design decisions of interplanetary spacecraft. The radiation section of this report used NASA's OLTARIS program to generate data for analysis. The area of focus was on the radiation effects for crewed missions, therefore effective dose equivalent was the metric used to compare different models of radiation and shielding. Test spheres with one, two, or three different materials layers were compared, along with modifiers such as alloys or weight vs. thickness emphasis. Results were compared to limits set by the European and Russian Space Agencies to provide context. The results hinged heavily on the intensity of the Solar Particle Events (SPEs), with testing using additional temporary radiation shielding proving to be a requirement for feasible shielding masses. Differences in shield material effectiveness were found to be negligible for thin Galactic Cosmic Rays (GCRs) and thick SPEs. Thick shields were found to perform better when the more efficient shield was on the outside of the test sphere. The micrometeoroid section used equations and programs from multiple sources to generate state vectors, flux, and finally impact models for four different case studies. Impacts v were generated with mass, velocity, and impact angle/location statistics. The mass and velocity results were run through statistical software to generate information such as mean and standard deviation with confidence intervals. Also looked at were higher mass impacts, limited to above 10-3 grams as opposed to above 10-6 for the regular case. The results of this show that very thin monolithic shields (0.1 cm-0.25 cm) could protect against the average 10-6 impact. The Ram, Nadir, and Anti-sun faces received the highest quantity of impacts and Wake received the least. When looking at the worst cases average mass and velocity for the high mass impacts significantly higher shielding was required to prevent penetration (up to 5 cm for some cases). However, the test cases had probabilities of no high mass impacts greater than 46% of the time, with shorter mission having greater chances of no high mass impacts.

No description available.

No description available.

No description available.

No description available.

No description available.

LLC resonant converters have been a popular choice for DC-DC converters due to their high efficiency, high power density, and hold-up capability in power supplies for communication systems, datacenters, consumer electronics, and automobiles. With the rapid development of wide-bandgap devices and novel magnetic materials, the push for higher switching frequencies to achieve higher power densities at lower costs is gaining traction. To demonstrate high efficiency and high power density, the Center for Power Electronics Systems (CPES) at Virginia Tech designed an 800W, 1MHz 400V/12V LLC converter for future datacenters, which could achieve a peak efficiency of 97.6% and a power density of 900 W/in3. However, with the ever-increasing demand for online services, the performance of power delivery must also be simultaneously improved to keep pace with the demand. The focus of this thesis is improving the performance of CPES’ previous 400V/12V LLC converter by investigating different aspects of its design and operation. Ultimately, design guidelines are proposed, and improvements are demonstrated to effectively achieve higher efficiency and higher power density than the previous CPES converter. Multiple aspects of the LLC converter’s design and structure are investigated to further improve its performance, and three main areas are the focus of this thesis. The output-side termination design of the planar transformer is investigated and modeled, and design guidelines for filter capacitor selection are provided for optimal efficiency. Next, the existing shielding technique for matrix transformers, which helps reduce common-mode (CM) noise without compromising on efficiency, is investigated for asymmetry and current-sharing issues, and modifications have been proposed to improve its efficiency. Thirdly, the LLC converter’s switching frequency is optimized to improve its performance over the previous CPES converter. Finally, the hardware results with the proposed improvements are demonstrated, and the converter’s performance is compared with the previous CPES converter as well as other recent proposed solutions. / M.S. / The electricity demand by datacenters has been growing exponentially over the past few decades, especially due to the boom of artificial intelligence in addition to other internet services. This has resulted in a requirement to continually improve the efficiencies of the power delivery from the grid, through the datacenter power architecture, and finally to the loads on the server racks. The overall datacenter power architecture has been improved over time to improve the total efficiency. However, the performance of each stage along the power architecture must be improved to keep in pace with the energy demand. The focus of this thesis is to improve the performance of the 400V/12V DC-DC stage for future datacenters. Previously, the Center for Power Electronics Systems (CPES) at Virginia Tech developed a 1MHz 800W 400V/12V LLC converter with 97.6% peak efficiency and 900W/in3 power density. However, the performance of the converter must be further improved to stay ahead of the competition and keep in pace with the increasing energy demand. Multiple aspects of the LLC converter’s design and structure are investigated to further improve its performance, and three main areas are the focus of this thesis. Firstly, the high-frequency termination design, or how different components are interconnected and arranged, is studied, and a capacitance selection guideline is proposed to maximize the efficiency. Next, the existing shielding technique for matrix transformers, which helps reduce common-mode (CM) noise without compromising on efficiency, is investigated for asymmetry and current-sharing issues, and modifications have been proposed to improve its efficiency. Thirdly, the LLC converter’s switching frequency is optimized to improve its performance over the previous CPES converter. Finally, the hardware results with the proposed improvements are demonstrated, and the converter’s performance is compared with the previous CPES converter as well as other recent proposed solutions.