Multi-walled carbon nanotubes (MWCNTs) and integrated MWCNTs/ SiO2 nanoparticles (NPs) were loaded as additives into nanocomposite polyvinylidene fluoride (PVDF) membranes fabricated via phase inversion methods, and the effects of these additives on the structure and vacuum membrane distillation (VMD) performance of the membranes have been studied. With an appropriate amount of MWCNTs (2 wt.% to PVDF) blended into the membrane, VMD performance of membrane was improved significantly due to higher membrane porosity, contact angle and surface roughness without extreme compromise of liquid entry pressure of water (LEPw), which could reach up to 72 psi. Further integration of MWCNTs with a small amount of SiO2 nanoparticles (NPs) showed a synergic effect resulting in further improvement of VMD flux due primarily to the increase in surface pore size. When the amount of SiO2 NPs additive was large, the effects of NPs dominates the VMD performance. However, the asymmetric structure of PVDF membrane disappears, which exercises an unfavourable effect on VMD performance. All fabricated membranes exhibited a great desalination potential with extremely high salt rejection (>99.98%). The incorporation of MWCNTs did not improve the tensile properties of the membrane.

In this study, we investigated the effect of electrolyte composition, photoanode thickness, and the additions of GuSCN (guanidinium thiocyanate), NMB (N-methylbenimidazole), and SiO2 on the photovoltaic performance of DSSCs (dye sensitized solar cells). A bifacial DSSC is realized and irradiated from front and rear sides. The devices give maximum photovoltaic efficiencies for 70% PMII (1-propyl 3-ethylimidazoliumiodide)/30%(EMIB(CN)4)(1-ethyl-3-methyl-imidazolium tetracyano borate) electrolyte composition and 10 &mu / m thick photoanode coating which is considered to be the ideal coating thickness for the diffusion length of electrolyte and dye absorption. A significant increase in the photocurrent for DSSCs with optimum molarity of 0.1 M GuSCN was observed due to decreased recombination which is believed to be surface passivation effect at photoanode electrolyte interface suppressing recombination rate. Moreover, optimum NMB molarity was found to be 0.4 for maximum efficiency. Addition of SiO2 to the electrolyte both as an overlayer and dispersed particles enhanced rear side illuminated cells where dispersed particles are found to be more efficient for the front side illuminated cells due to additional electron transport properties. Best rear side illuminated cell efficiency was 3.2% compared to front side illuminated cell efficiency of 4.2% which is a promising result for future rear side dye sensitized solar cell applications where front side illumination is not possible like tandem structures and for cells working from both front and rear side illuminations.

Wood is a widely used construction material that has many advantageous properties, and some drawbacks. These drawbacks are mainly associated with the porous vascular structure of wood that makes it a high water-absorbent material. In addition, wood’s properties alter substantially with respect to the moisture content. Amongst the treatment techniques that limit the water uptake capacity of wood, vacuum-aided impregnation has exhibited promising results. However, little research has explored the effect of key parameters (such as the vacuum pressure) on the effectiveness of the impregnation. This study aims to optimize the performance of SiO2 impregnation of spruce wood under vacuum pressures. The main objective of this research is to overcome wood’s weakness by reducing its water uptake capacity through a vacuum-aided impregnation technique and study its effect on the physico-mechanical properties of wood under dry and saturated conditions. The study was conducted in two parts. In the first part, wood samples underwent impregnation under atmospheric and three vacuum pressures. Density measurements, water uptake tests, microscopy examination, thermogravimetric analysis, and dynamic mechanical analysis were conducted on non-treated and SiO2-treated samples. Quantitative and qualitative analyses demonstrated that SiO2 impregnation performed under -90 kPa was able to effectively enhance the wood’s properties compared to the other conditions. The SiO2 impregnation under high vacuum pressure demonstrated an effective increase in the density of the wood and achieved a significant reduction in the water uptake capacity. The analysis of the wood’s viscoelastic properties revealed that SiO2 impregnation under atmospheric and vacuum conditions triggered two different reinforcing mechanisms: a solid film, causing stick-slip oscillation, and particle diffusion, causing particle-particle and particle-lumen wall friction, respectively. For the second part, characterization methods such as Impact test, DMA, SEM, EDS, Porosity, and SAXS tests were conducted on non-treated and -90 kPa treated spruce wood samples in dry, saturated, and submerged states in order to reveal the synergistic effect of the SiO2 impregnation pressure and water uptake on the wood’s properties. The results showed that high vacuum impregnation pressure has a significant positive reinforcing effect on the wood’s properties. It increased the impact resistance of wood in dry and saturated conditions. A high vacuum impregnation was able to overcome the softening effect of water and caused a significant increase in the Storage modulus by strengthening the wood’s vascular structure, which accordingly increased the wood’s capacity to absorb energy. High vacuum impregnation was also able to counteract the plasticizing effect of water and significantly increased the Loss modulus by increasing the internal friction in the wood with the diffusion of the nanoparticles in the wood’s cell walls and vascular structure. This phenomenon increased the wood's capacity to absorb and dissipate energy under dry and submerged conditions.