No description available.

Thesis (M.S.)--University of Texas at El Paso, 2009. / Title from title screen. Vita. CD-ROM. Includes bibliographical references. Also available online.

The compressive creep behaviour of a high purity silicon nitride ceramic with and without the addition of Ba was studied at 1400°C. Two distinct creep stages were observed during high temperature deformation of these materials. The stress exponents for creep of the two materials indicate that they have different creep mechanisms during the second stage of creep. Cavitation during creep was determined by measuring the density change before and after creep using a water­-displacement method. The Ba doped material exhibited an obvious density decrease, indicating cavitation during creep, whereas the undoped material exhibited no cavitation. This is consistent with TEM observations. The microstructure of the materials, especially the amorphous grain-boundary phase was investigated for both as-sintered and crept specimans by means of transmission electron microscopy (TEM). Statistical analysis of a number of grain-­boundary films indicates that the film thickness is confined to a narrow range (standard deviation less than 0.15 nm) in the as-sintered materials. The average film thickness depends on film chemistry, increasing from 1.0 nm to 1.4 nm when Ba is added. The standard deviation of the film thickness of a given material after creep, however, is considerably larger than before (0.30 nm ~ 0.59 nm). This suggests that the grain-boundary glass phase is redistributed during creep. Viscous flow of the glass phase is proposed as die mechanism responsible for the first stage of creep. The data are compared with a model for viscous creep, yielding good correlation. / Thesis / Master of Engineering (ME)

<p>Spark Plasma Sintering (SPS) is a promising rapid consolidation technique that allows a better understanding and manipulating of sintering kinetics and therefore makes it possible to obtain Si₃N₄-based ceramics with tailored microstructures, consisting of grains with either equiaxed or elongated morphology.</p><p> The presence of an extra liquid phase is necessary for forming tough interlocking microstructures in Yb/Y-stabilised α-sialon by HP. The liquid is introduced by a new method, namely by increasing the O/N ratio in the general formula RE_xSi_12-(3x+n)Al_3x+nO_nN_16-n while keeping the cation ratios of RE, Si and Al constant. </p><p>Monophasic α-sialon ceramics with tailored microstructures, consisting of either fine equiaxed or elongated grains, have been obtained by using SPS, whether or not such an extra liquid phase is involved. The three processes, namely densification, phase transformation and grain growth, which usually occur simultaneously during conventional HP consolidation of Si₃N₄-based ceramics, have been precisely followed and separately investigated in the SPS process.</p><p>The enhanced densification is attributed to the non-equilibrium nature of the liquid phase formed during heating. The dominating mechanism during densification is the enhanced grain boundary sliding accompanied by diffusion- and/or reaction-controlled processes. The rapid grain growth is ascribed to a <i>dynamic ripening</i> mechanism based on the formation of a liquid phase that is grossly out of equilibrium, which in turn generates an extra chemical driving force for mass transfer. Monophasic α-sialon ceramics with interlocking microstructures exhibit improved damage tolerance. Y/Yb- stabilised monophasic α-sialon ceramics containing approximately 3 vol% liquid with refined interlocking microstructures have excellent thermal-shock resistance, comparable to the best β-sialon ceramics with 20 vol% additional liquid phase prepared by HP. </p><p>The obtained sialon ceramics with fine-grained microstructure show formidably improved <i>superplasticity</i> in the presence of an electric field. The compressive strain rate reaches the order of 10^-2 s^-1 at temperatures above 1500oC, that is, two orders of magnitude higher than that has been realised so far by any other conventional approaches. The high deformation rate recorded in this work opens up possibilities for making ceramic components with complex shapes through super-plastic forming. </p>

Spark Plasma Sintering (SPS) is a promising rapid consolidation technique that allows a better understanding and manipulating of sintering kinetics and therefore makes it possible to obtain Si3N4-based ceramics with tailored microstructures, consisting of grains with either equiaxed or elongated morphology. The presence of an extra liquid phase is necessary for forming tough interlocking microstructures in Yb/Y-stabilised α-sialon by HP. The liquid is introduced by a new method, namely by increasing the O/N ratio in the general formula RExSi12-(3x+n)Al3x+nOnN16-n while keeping the cation ratios of RE, Si and Al constant. Monophasic α-sialon ceramics with tailored microstructures, consisting of either fine equiaxed or elongated grains, have been obtained by using SPS, whether or not such an extra liquid phase is involved. The three processes, namely densification, phase transformation and grain growth, which usually occur simultaneously during conventional HP consolidation of Si3N4-based ceramics, have been precisely followed and separately investigated in the SPS process. The enhanced densification is attributed to the non-equilibrium nature of the liquid phase formed during heating. The dominating mechanism during densification is the enhanced grain boundary sliding accompanied by diffusion- and/or reaction-controlled processes. The rapid grain growth is ascribed to a dynamic ripening mechanism based on the formation of a liquid phase that is grossly out of equilibrium, which in turn generates an extra chemical driving force for mass transfer. Monophasic α-sialon ceramics with interlocking microstructures exhibit improved damage tolerance. Y/Yb- stabilised monophasic α-sialon ceramics containing approximately 3 vol% liquid with refined interlocking microstructures have excellent thermal-shock resistance, comparable to the best β-sialon ceramics with 20 vol% additional liquid phase prepared by HP. The obtained sialon ceramics with fine-grained microstructure show formidably improved superplasticity in the presence of an electric field. The compressive strain rate reaches the order of 10-2 s-1 at temperatures above 1500oC, that is, two orders of magnitude higher than that has been realised so far by any other conventional approaches. The high deformation rate recorded in this work opens up possibilities for making ceramic components with complex shapes through super-plastic forming.