4 ABSTRACT Development and testing of novel non-toxic electrode materials, detection arrangements and analytical methods applicable in determination of selected agrochemicals is the main aim of this Ph.D. Thesis. New working electrodes based on silver solid amalgam paste (AgSA-PE) with organic pasting liquid and other based on crystallic silver amalgam (CAgAE) were developed, their electrochemical behaviour investigated and further used in voltammetric determination of widespread and toxic environmental pollutant 4-nitrophenol (4-NP). This analyte could be determined by DPV at AgSA-PE with limit of detection (LD) 1×10í6 mol lí1 and using CAgAE with LD 4×10í7 mol lí1 , both in 0.2 mol lí1 acetate buffer pH 4.8. Attempts to decrease LDs by utilization of adsorptive stripping voltammetry were not successful in either case. Crystallic silver amalgam was also successfully used for construction of microcylindric flow-through cell and tested for amperometric determination of nitrophenol mixture in HPLC-ED system. Both novel electrodes were found to be suitable alternatives to toxic mercury electrodes and the CAgAE seems to be promising working electrode for flowing systems. Method for sample preparation and voltammetric determination of broad-spectrum herbicide Glyphosate in contaminated soil samples was also...

The partial removal of carious dentine was studied by means of a literature review and a multicenter randomized controlled clinical trial. The clinical trial compared the effectiveness of an alternative treatment for deep caries lesions and the stepwise excavation in Public Health Services in Brazil. The treatment consists of partial removal of carious dentine followed by restoration in one session. A cost-effectiveness analysis the two treatments was performed. The clinical performance of amalgam and resin restorations placed in deep caries lesions with or without decayed tissue beneath them was also evaluated. Inclusion criteria: patients with ≥ nine years old, permanent molars with deep caries lesions and absence of periapical alterations, pulp sensitivity; absence of spontaneous pain; negative percussion test. The subjects were assigned to: test-group - partial removal of carious dentine (PDR) and restoration, and control-group - stepwise excavation (SW). SW consists of partial removal of carious tissue, indirect pulp capping with calcium hydroxide cement; temporary filling; cavity re-opening after 60 days, removal of the remaining soft carious tissue and filling. Clinical and radiological exams were performed annually. The outcomes were: (1) pulp sensitivity to cold test and absence of periapical alterations, assuming those parameters as indicators of pulp vitality; and (2) success of the restoration. To determine the cost-effectiveness of the treatments, the discounted cash flow method was adopted. The data were submitted to Kaplan-Meier, Log-rank test and logistic regression analysis, P<0.05. There were performed 299 treatments, 146 SW and 153 tests. There were no differences between the groups regarding baseline characteristics - age, gender and family income. The number of teeth evaluated after one and two years were 180 and 122. After one year of treatment performance, the therapy success rates were 97.9% and 74.1% of success in test and control groups respectively (P<0.000). After 2 years of follow-up, therapy survival rates of PDR and SW were 93.7% and 73.3% respectively (P=0.000). A total of 29 therapeutic failures were observed: PDR group - pulpitis (n=3), osteitis (n=1), hyperemia (n=2); SW group - pulpitis (n=15), necrosis (n=6), extraction (n=1) and restoration fracture (n=1). None of the variables studied showed a significant causal influence on the success rate, besides the type of treatment. After two year of follow-up, 181 restorations had been evaluated, 86 from the SW group and 95 from the PDR group; 65.8% were from the resin composite group and 34.2% were amalgam restorations. The survival analysis of the treatment associated with the filling material showed no difference in the rate of success (P=0.564). Regarding the treatment, both groups presented a similar rate of success: SW=95.3% and PDR=94.7% (P=0.928). Resin composite restorations presented 96.8% of success and amalgam restorations presented 94.1% of success (P=0.446). The reason for failure was fracture of filling material. The PDR provides an economy of R$ 143.37 (67.78%) per treatment compare to SW and 2.39% in the overall economy in the annual cost of the public health center. Partial caries removal could be performed as definitive treatment and the procedure of re-opening the cavity to remove the residual infected dentine is not necessary. The maintenance of carious dentine does not interfere in the maintenance of pulp vitality. The presence of decayed tissue in deep caries lesions does not seem to interfere with the survival of the restorations. Performing the partial removal of carious dentine in one session generates benefits for the public finances (direct economy), for the public health services (increase in number of treatments performed) and for the patients (comfort and time).

The partial removal of carious dentine was studied by means of a literature review and a multicenter randomized controlled clinical trial. The clinical trial compared the effectiveness of an alternative treatment for deep caries lesions and the stepwise excavation in Public Health Services in Brazil. The treatment consists of partial removal of carious dentine followed by restoration in one session. A cost-effectiveness analysis the two treatments was performed. The clinical performance of amalgam and resin restorations placed in deep caries lesions with or without decayed tissue beneath them was also evaluated. Inclusion criteria: patients with ≥ nine years old, permanent molars with deep caries lesions and absence of periapical alterations, pulp sensitivity; absence of spontaneous pain; negative percussion test. The subjects were assigned to: test-group - partial removal of carious dentine (PDR) and restoration, and control-group - stepwise excavation (SW). SW consists of partial removal of carious tissue, indirect pulp capping with calcium hydroxide cement; temporary filling; cavity re-opening after 60 days, removal of the remaining soft carious tissue and filling. Clinical and radiological exams were performed annually. The outcomes were: (1) pulp sensitivity to cold test and absence of periapical alterations, assuming those parameters as indicators of pulp vitality; and (2) success of the restoration. To determine the cost-effectiveness of the treatments, the discounted cash flow method was adopted. The data were submitted to Kaplan-Meier, Log-rank test and logistic regression analysis, P<0.05. There were performed 299 treatments, 146 SW and 153 tests. There were no differences between the groups regarding baseline characteristics - age, gender and family income. The number of teeth evaluated after one and two years were 180 and 122. After one year of treatment performance, the therapy success rates were 97.9% and 74.1% of success in test and control groups respectively (P<0.000). After 2 years of follow-up, therapy survival rates of PDR and SW were 93.7% and 73.3% respectively (P=0.000). A total of 29 therapeutic failures were observed: PDR group - pulpitis (n=3), osteitis (n=1), hyperemia (n=2); SW group - pulpitis (n=15), necrosis (n=6), extraction (n=1) and restoration fracture (n=1). None of the variables studied showed a significant causal influence on the success rate, besides the type of treatment. After two year of follow-up, 181 restorations had been evaluated, 86 from the SW group and 95 from the PDR group; 65.8% were from the resin composite group and 34.2% were amalgam restorations. The survival analysis of the treatment associated with the filling material showed no difference in the rate of success (P=0.564). Regarding the treatment, both groups presented a similar rate of success: SW=95.3% and PDR=94.7% (P=0.928). Resin composite restorations presented 96.8% of success and amalgam restorations presented 94.1% of success (P=0.446). The reason for failure was fracture of filling material. The PDR provides an economy of R$ 143.37 (67.78%) per treatment compare to SW and 2.39% in the overall economy in the annual cost of the public health center. Partial caries removal could be performed as definitive treatment and the procedure of re-opening the cavity to remove the residual infected dentine is not necessary. The maintenance of carious dentine does not interfere in the maintenance of pulp vitality. The presence of decayed tissue in deep caries lesions does not seem to interfere with the survival of the restorations. Performing the partial removal of carious dentine in one session generates benefits for the public finances (direct economy), for the public health services (increase in number of treatments performed) and for the patients (comfort and time).

The partial removal of carious dentine was studied by means of a literature review and a multicenter randomized controlled clinical trial. The clinical trial compared the effectiveness of an alternative treatment for deep caries lesions and the stepwise excavation in Public Health Services in Brazil. The treatment consists of partial removal of carious dentine followed by restoration in one session. A cost-effectiveness analysis the two treatments was performed. The clinical performance of amalgam and resin restorations placed in deep caries lesions with or without decayed tissue beneath them was also evaluated. Inclusion criteria: patients with ≥ nine years old, permanent molars with deep caries lesions and absence of periapical alterations, pulp sensitivity; absence of spontaneous pain; negative percussion test. The subjects were assigned to: test-group - partial removal of carious dentine (PDR) and restoration, and control-group - stepwise excavation (SW). SW consists of partial removal of carious tissue, indirect pulp capping with calcium hydroxide cement; temporary filling; cavity re-opening after 60 days, removal of the remaining soft carious tissue and filling. Clinical and radiological exams were performed annually. The outcomes were: (1) pulp sensitivity to cold test and absence of periapical alterations, assuming those parameters as indicators of pulp vitality; and (2) success of the restoration. To determine the cost-effectiveness of the treatments, the discounted cash flow method was adopted. The data were submitted to Kaplan-Meier, Log-rank test and logistic regression analysis, P<0.05. There were performed 299 treatments, 146 SW and 153 tests. There were no differences between the groups regarding baseline characteristics - age, gender and family income. The number of teeth evaluated after one and two years were 180 and 122. After one year of treatment performance, the therapy success rates were 97.9% and 74.1% of success in test and control groups respectively (P<0.000). After 2 years of follow-up, therapy survival rates of PDR and SW were 93.7% and 73.3% respectively (P=0.000). A total of 29 therapeutic failures were observed: PDR group - pulpitis (n=3), osteitis (n=1), hyperemia (n=2); SW group - pulpitis (n=15), necrosis (n=6), extraction (n=1) and restoration fracture (n=1). None of the variables studied showed a significant causal influence on the success rate, besides the type of treatment. After two year of follow-up, 181 restorations had been evaluated, 86 from the SW group and 95 from the PDR group; 65.8% were from the resin composite group and 34.2% were amalgam restorations. The survival analysis of the treatment associated with the filling material showed no difference in the rate of success (P=0.564). Regarding the treatment, both groups presented a similar rate of success: SW=95.3% and PDR=94.7% (P=0.928). Resin composite restorations presented 96.8% of success and amalgam restorations presented 94.1% of success (P=0.446). The reason for failure was fracture of filling material. The PDR provides an economy of R$ 143.37 (67.78%) per treatment compare to SW and 2.39% in the overall economy in the annual cost of the public health center. Partial caries removal could be performed as definitive treatment and the procedure of re-opening the cavity to remove the residual infected dentine is not necessary. The maintenance of carious dentine does not interfere in the maintenance of pulp vitality. The presence of decayed tissue in deep caries lesions does not seem to interfere with the survival of the restorations. Performing the partial removal of carious dentine in one session generates benefits for the public finances (direct economy), for the public health services (increase in number of treatments performed) and for the patients (comfort and time).

The submitted work deals with the application of voltammetric determination of Fomesafen using non-traditional mercury meniscus modified silver solid amalgam electrode on model samples of Fomesafen in real aqueous matrices of drinking and river water. This method of measurement has been developed and optimized in my bachelor thesis, which the diploma thesis is related to. Fomesafen belongs to a group of herbicides used on a mass scale in the late 20th century in the USA and in many countries around the world still used even today. Among its side effects according to the EPA include, among others, potential carcinogenicity to humans and confirmed carcinogenicity to some mammals (such as rats) which led to a legislative regulation on its use in many countries around the world including the USA, the European Union and many others. Silver solid amalgam electrode has been developed with the intention to limit the use of mercury in accordance with new legislation of the European Union and the concept of green analytical chemistry. Despite the low levels of mercury mainly bound in the form of virtually harmless silver amalgam electrode retains very similar electrochemical properties with proven mercury electrodes. As part of the thesis, direct determination of a number of partial extraction of Fomesafen...

5 Abstract This Diploma Thesis is targeted on the determination of 5-nitrobenzimidazole (5-NBIA) using following techniques: DC voltammetry (DCV) and differential pulse voltammetry (DPV). As working electrodes, a silver amalgam paste electrode (AgA-PE), which was constructed for this determination in the form of a new prototype, a bismuth film electrode (BiFE), at which the optimum conditions for the deposition of the bismuth film at a suitable substrate (glassy carbon electrode and gold electrode were tested for this purpose) were initially optimized, and a glassy carbon electrode (GCE) were used. The optimum conditions for the voltammetric determination of 5-NBIA at the AgA-PE (in a medium of Britton-Robinson buffer (BR-buffer) of pH 7.0 for both DCV and DPV), at the BiFE with gold substrate (BR-buffer of pH 9.0 for both DCV and DPV; the film was deposited "ex situ" in a stirred plating solution (1000 mg L-1 Bi(III) solution in 0.1 mol L-1 acetate buffer of pH 4.5) for 300 s), and at the GCE (BR-buffer of pH 5,0 for both DCV and DPV). Under these conditions, calibration dependences were measured in the concentration ranges of 0.1 - 100 µmol L-1 (pro DCV a DPV na AgA-PE) and 1 - 100 µmol L-1 (pro DCV a DPV na BiFE a GCE), and the limits of quantification (LQs) were calculated for particular methods: LQ ≈...

Voltammetric methods for determination of 1,3-dinitronaphthalene (1,3-DNN), 1,5-dinitronaphthalene (1,5-DNN) and 1,8-dinitronaphthalene (1,8-DNN) using DC voltammetry (DCV) and differential pulse voltammetry (DPV) at novel single crystal silver amalgam electrode (CAgAE) were developed in this work. Developed methods may be used for determination of 1,3-DNN within a concentration range 2 - 10 μmol.L-1 with LoQ 2 μmol.L-1 using DCV and 1 - 100 μmol.L-1 with LoQ 1 μmol.L-1 by DPV; 1,5-DNN wihin a concentration range 2 - 10 μmol.L-1 with LoQ 2 μmol.L-1 using DCV and 1 - 10 μmol.L-1 with LoQ 1 μmol.L-1 by DPV and 1,8-DNN within a concentration range 2 - 10 μmol.L-1 with LoQ 2 μmol.L-1 using DCV and 0,3 - 1 μmol.L-1 with LoQ 0,3 μmol.L-1 by DPV. An attepmt to decrease LoQ by adsorptive stripping differential pulse voltammetry was not successful. Process of electrochemical reduction of selected dinitronaphthalenes on the working electrode was also studied by cyclic voltammetry. This work verified the use of CAgAE as alternative electrode material to mercury electrodes for determination of electrochemically reducible organic compounds in aqueous-methanolic media. Small dimensions of the CAgAE are the main advantages which predetermine its use in voltammetric microvolume batch analysis and amperometric detection in...

<p>Danas, u raznim analitičkim laboratorijama postoji veći broj analitičkih protokola,<br />zasnovanih bilo na izuzetno sofisticiranim ili jednostavnijim tehnikama, koji služe za<br />određivanje različitih ciljnih analita od farmakolo&scaron;kog značaja. Među tim grupama ciljnih analita pripadaju i antibiotici koji predstavljaju veliko otkriće u oblasti medicine i zahvaljujući njima spa&scaron;eno je vi&scaron;e od sedam miliona života, ali pored navedenih koristi, antibiotici mogu da izazovu&nbsp; veliki broj neželjenih efekata i žučne kiseline zajedno sa svojim derivatima, koji su fiziolo&scaron;ki deterdženti, mogu biti citotoksične za organizam ako se njihova koncentracija ne kontroli&scaron;e. U ovoj doktorskoj disertaciji prikazan je razvoj analitičkih metoda pre svega voltametrijskihmetoda u kombinaciji sa jednostavnim i savremenim elektrodama/senzorima za određivanje&nbsp; odabranih analita kao &scaron;to je antraciklični antibiotik doksorubicin (DOX), makrolidni antibiotici<br />eritromicin-etilsukcinata (EES), azitromicina (AZI), klaritromicina (CLA) i roksitromicina&nbsp; (ROX) i 3-dehidro-deoksiholne kiseline.</p><p>Voltametrijska karakterizacija i određivanje gore navedenih antibiotika primenom obnovljive srebro-amalgam film elektrode (Hg(Ag)FE)rađena je direktnom katodnom&nbsp; voltametrijom sa pravougaonim talasima (SWV) i visoko osetljivom adsorptivnom voltametrijom sa pravougaonim talasima (SW-AdSV) u Briton-Robinson puferu, kao pomoćnom elektrolitu, obuhvatajući &scaron;irok opseg pH vrednosti. Odgovor DOX-a primenom&nbsp; Hg(Ag)FE&nbsp;praćen je u intervalu potencijala od -0,20 do -0,80 V.&nbsp; Za analizu tragova, optimizacija metode ukazuje da su optimalni parametri za analitički pik na potencijalu (Ep ) -0,57 V u odnosu na zasićenu kalomelovu elektrodu (ZKE): pH 6,0, potencijal&nbsp; akumulacije -0,20 V i vreme&nbsp; akumulacije 140 s. U model rastvoru, DOX je određivan u koncentracionom opsegu 4,99-59,64&nbsp; ng mL^-1. Razvijena SW-AdSV metoda je primenjena za određivanje DOX-a u obogaćenom uzorku humanog urina. Niža koncentracija DOX-a 9,89ng mL^-1&nbsp;u voltametrijskoj&nbsp; ćeliji je određivana sa relativnom standardnom devijacijom (RSD) manjom od 6,0%. &Scaron;to se ispitivanih makrolida tiče oni su pokazali redukcione signale u dalekoj negativnoj oblasti potencijala. Ispitivanja direktnom katodnom SWV rađena su u opsegu potencijala od -0,75 V do -2,00 V u odnosu na ZKE, pri čemu su dobijena jedan ili dva redukciona pika u opsegu potencijala od -1,5 V do -1,9 V. Oblik i intenzitet signala zavisi od primenjene pH vrednosti u &scaron;irokoj pH oblasti. Za analitičke svrhe, radi razvoja direktne katodne SWV i adsorptivne inverzne/striping SWV metode, pogodnim su se pokazale neutralna i slabo alkalna sredina tj. pH 7,0 sa&nbsp; E_p na -1,67 V u odnosu na ZKE za ROX i EES i pH 7,2 sa E_p na -1,85 V u odnosu na ZKE za AZI i pH 7,4 sa E_p na -1,64 V u odnosu na ZKE za CLA. Na osnovu snimljenih cikličnih voltamograma na&nbsp; optimalnim pH vrednostima, može se predložiti adsorptivno-kontrolisan kinetički proces na elektrodi u slučaju sva&nbsp; četiri ispitivana jedinjenja. Takođe,&nbsp; ¹H NMR merenja uz potiskivanje&nbsp; signala vode u pH oblasti između pH 6,0 i 10,5 ukazuju na to da su makrolidni molekuli pri optimalnim analitičkim uslovima predominantno u protonovanoj formi preko tercijerne amino grupe &scaron;to potpomaže, u sva&nbsp; četiri slučaja, njihovu adsorpciju na odgovarajuće polarizovanoj Hg(Ag)FE. Optimizovane direktne katodne SWV metode&nbsp; pokazuju dobru linearnost u koncentracionom opsegu 4,81-23,3&nbsp; &micro;g mL^-1 , 4,53-29,8&nbsp; &micro;g mL^-1 , 1,96-28,6&nbsp; &micro;g mL^-1 i 1,48-25,9 &micro;g mL^-1 za AZI, EES, CLA odnosno ROX. Razvijene SW-AdSV metode rezultiraju u linearnom odgovoru pri nižim koncentracionim intervalima 1,0-2,46 &micro;g mL^-1 ,&nbsp; 0,69-2,44&nbsp; &micro;g mL^-1, 0,05-0,99 &micro;g mL^-1 i 0,10-0,99&nbsp; &micro;g mL^-1 , za AZI, EES, CLA i ROX. RSD za sve razvijene metode nije veća od 1,5% izuzev SWV metode u slučaju AZI-a gde je 4,5%. Direktna katodna SWV metoda&nbsp; je uspe&scaron;no primenjena za određivanje EES-a u farmaceutskom proizvodu Eritromicin^&reg; dok SW-AdSV metoda je primenjena u slučaju određivanja EES-a u obogaćenom uzorku humanog urina i&nbsp;za određivanje ROX-a u farmaceutskom proizvodu Runac^&reg; . U svim pomenutim slučajevima, primenjena je metoda standardnog dodatka. Pouzdanost i tačnost elaboriranih procedura u slučaju određivanja EES-a u model sistemu i&nbsp; farmaceutskom proizvodu Eritromicin^&reg; su potvrđena poređenjem sa rezultatima dobijenim primenom HPLC-DAD metode.</p><p>Nakon preliminarnih studija 3-dehidro-deoksiholne&nbsp; kiseline/3-dehidro-deoksiholata primenom elektrode od staklastog ugljenika (GCE), gde je uočeno da ne dolazi do formiranja redukcionog signala u Briton-Robinson puferu između pH 5,0 i 11,8 primenom direktne katodne SWV, bizmut-film je izdvojen&nbsp; <em>ex situ</em> na povr&scaron;ini iste elektrode od staklastog ugljenika (BiF-GCE) iz uobičajeno kori&scaron;ćenog rastvora za elektrodepoziciju (0,02 mol L^-1 Bi(NO₃)₃, 1,0 mol L^-1 HCl i 0,5 mol L^-1 KBr) i tako pripremljena elektroda je primenjena za karakterizaciju i određivanje pomenutog jedinjenja u alkalnoj sredini. Redukcioni signal ispitivanog analita od analitičkog značaja je uočen jedino primenom BiF-GCE u Briton-Robinson puferusa pH vrednostima između 9,5 i 11,8 u režimu adsorptivne inverzne/stripingvoltametrije sa pravougaonim talasima, dok u slučaju direktnih katodnih SWV eksperimentalnih uslova uočen je slab redukcioni pik sa niskom strujom maksimuma pika. Optimizovani eksperimentalni uslovi za određivanje 3-dehidro-deoksiholata obuhvataju odgovarajuće kondicioniranje elektrode uključujući kondicioniranje&nbsp; <em>ex situ</em> pripremljene BiF-GCE u Briton-Robinson pomoćnom elektrolitu pH 11,8 do stabilizacije struje bazne linije elektrohemijskim cikliranjem potencijala radne elektrode u potencijalskom opsegu između -1,00 i -2,00 V u odnosu na ZKE (blizu 15 puta) i primenu dva ključna parametara adsorptivne voltametrije sa pravougaonim talasima: vreme akumulacije od 30 s i potencijal akumulacije&nbsp; -1,00 V u odnosu na ZKE. Zbog relativne asimetričnosti dobijenih redukcionih signala ispitivanog analita sa&nbsp; E_p na -1,35 V u odnosu na ZKE, &scaron;to je takođe prisutno i u slučaju primene SW-AdSV, određivanje ispitivanog analita je zasnovano na linearnoj zavisnosti između povr&scaron;ine pika redukcionog signala&nbsp; spitivanog analita i njegove odgovarajuće koncentracije i postignuta granica detekcije je 1,43 &micro;g mL^-1 sa dva linearna opsega kalibracione krive od 4,76 &micro;g mL^-1 do 13,0 &micro;g mL^-1 i od 13,0 &micro;g mL^-1 do 23,1 &micro;g mL^-1 za razvoj analitičke metode. RSD metode je 3,22%. Dodatni eksperimenti, elektroliza ispitivanog analita na potencijalu -1,55 V (blizu maksimuma pika ciljnog analita) u odnosu na ZKE su rađeni primenom GCE u obliku ploče (povr&scaron;ina 33,52 cm 2 ) modifikovane sa&nbsp; <em>ex situ&nbsp;</em>pripremljenim bizmut-filmom. Rastvor od interesa uzorkovan je na početku eksperimenta, nakon 2,5 h i nakon 4,5 h tretmana. Ovakvi uzorci su analizirani primenom ¹H NMR merenja uz potiskivanje signala vode u puferskom rastvoru pH 11,8. Može se pretpostaviti da tokom elektrolize 3-dehidro-deoksiholata dolazi do redukcije keto grupe prisutne u strukturi ispitivanog analita.</p><p>Na osnovu literaturnih podataka da neki od ciljnihmakrolidnih antibiotika kao &scaron;to je npr. azitromicin pokazuju oksidativno pona&scaron;anje na elektrodi od ugljenične paste i elektrodi od zlata deteljna karakterizacija i određivanje&nbsp; četiri makrolidna antibiotika rađena je primenom&nbsp; asične&nbsp;elektrode od ugljenične paste (CPE) koja se sastoji samo od grafitnog praha i parafinskog ulja sa optimizovanih direktnih anodnih SWV metoda. U slučaju EES-a i AZI-a diferencijalna pulsna voltametrija (DPV) je testirana za iste svrhe. Ključni&nbsp; parametar u slučaju razvoja analitičkih voltametrijskih metoda je odabir pH vrednosti pomoćnog elektrolita gde je oblik/simetričnost i intenzitet oskidacionog pika glavni kriterijum prilikom odabira. Kao odgovarajuće pH vrednosti za voltametrijsko određivanje EES-a primenom SWV metode odabrana je pH 8,0 sa E_p na 0,83<br />V u odnosu na ZKE, dok u slučaju DPV metode pH 12,0 sa&nbsp; E_p na 0,55 V u odnosu na ZKE je bila najpogodnija za analitičke svrhe. Za određivanje AZI-a, u slučaju obe SWV i DPV metode pH 7,0 se pokazala najpogodnijom sa E_p analitičkog signala na 0,85 V odnosno 0,80 V u odnosu na ZKE, dok u slučaju CLA i ROX koji su ispitivani samo primenom SWV metode za analitičke svrhe pH 12,0 je bila najpogodnija sredina sa E_p analitičkog signala na 0,65 V odnosno na 0,63 V&nbsp;u odnosu na ZKE. Postignute granice detkcije primenom nemodifikovane CPE i direktne anodne SWV su uglavnom u submikrogramskom koncentracionom opsegu 0,17 &micro;g mL^-1 , 0,32&nbsp; &micro;g mL^-1 i 0,30&nbsp; &micro;g mL^-1, u slučaju EES-a, AZI-a i ROX-a i u niskom mikrogramskom koncentracionom opsegu 1,43&nbsp; &micro;g mL^-1 za CLA. Razvijena SWV metoda sa jednostavnom CPE pokazala se pogodnom za određivanje ROX-a u komercijalnom proizvodu Runac^&reg; tableti. U slučaju optimizovanih DPV metoda postignute granice detekcije za EES i AZI su u niskom mikrogramskom&nbsp; koncentracionom opsegu 1,03&nbsp; &micro;g mL^-1 odnosno 1,53&nbsp; &micro;g&nbsp; mL^-1 . U želji da se&nbsp;postigne niža granica detekcije za AZI, DPV metoda&nbsp; je testirana u kombinaciji sa&nbsp; CPE radnom elektrodom povr&scaron;inski modifikovanom sa zlatnim nanočesticama&nbsp; prečnika 10 nm (Au-CPE) i&nbsp; postignuta granica detekcije je 0,95&nbsp; &micro;g mL^-1 sa&nbsp; E_p analitičkog signala na 0,80 V u odnosu na&nbsp; ZKE. RSD metode u slučaju Au-CPE je 3,5%, dok je u slučaju nemodifikovane CPE 6,0%.&nbsp; Linearnost analitičke metode zasnovane na primeni Au-CPE je dva puta &scaron;ira nego u slučaju&nbsp; primene nemodifikovane CPE.</p><p>Na osnovu dobijenih rezultata može se zaključiti da&nbsp; odgovarajuće kombinacije&nbsp; optimizovanih voltametrijskih tehnika sa ekolo&scaron;ki prihvatljivim i lako primenljivim radnim&nbsp; elektrodama, kao &scaron;to su Hg(Ag)FE, BiF-GCE i CPE zajedno sa Au-CPE, rezultuju razvojem&nbsp; pouzdanih analitičkih metoda, kako u oksidacionim tako i u redukcionim proučavanjima, koje&nbsp; često omogućuju&nbsp; određivanje tragova analita od farmakolo&scaron;kog značaja u jednostavnim, a u&nbsp;nekim slučajevima i u složenim sistemima.&nbsp;</p> / <p>Nowadays in different analytical laboratories there is the increasing number of analytical protocols, either based on highly sophisticated or simpler measurements techniques, which serving for determination of different target analytes of pharmacological importance. Among such target groups of the analyte belongs the antibiotics which present a great discovery in the field of medicine and thanks to them were saved more than seven million people but beside to the mentioned great benefits, antibiotics can cause a large number of side effects and bile acids together with their derivatives which are physiological detergents but if their concentration is not<br />controlled they can be cytotoxic to the body. In the present doctoral dissertation the development of analytical methods, primarily analytical voltammetric methods in combination with simple and contemporary electrodes/sensors, for the determination of selected analytes as antracycline antibiotic doxorubicin (DOX), macrolide antibiotics erythromycin ethylsuccinate (EES), azithromycin (AZI), clarithromycin (CLA) and roxithromycin (ROX) and 3-dehydrodeoxycholic acid were performed.</p><p>Voltammetric characterization and determination of the above mentioned antibiotics using a renewable silver-amalgam film electrode (Hg(Ag)FE) was performed by direct cathodic square-wave voltammetry (SWV) and by highly sensitive adsorptive square-wave voltammetry (SW-AdSV) in aqueous Britton-Robinson buffer solutions as supporting electrolyte covering the wider pH range. The Hg(Ag)FE response of DOX was monitored in the potential range between -0.20 and -0.80 V. For the trace level analysis the method optimization showed that the optimal conditions for the analytical peak with peak potential (E_p) at -0.57 V vs. SCE were: the pH 6.0, the accumulation potential -0.20 V, and the accumulation time 140 s. In the model solutions, DOX was determined in the concentration range of 4.99-59.64 ng mL^-1. The developed SWAdSV method was applied for the determination of DOX in spiked human urine sample. The lowest concentration of DOX of 9.89 ng mL^-1 in voltammetric vessel was determined with the relative standard deviation (RSD) less than 6%. As for the investigated macrolides, they showed reduction signals in fairly negative potential range. During direct cathodic SWV investigations conducted over the potential range from -0.75 V to -2.00 V vs. SCE, either one or two reduction peaks were obtained in the&nbsp; potential range from -1.5 to -1.9 V. For analytical purposes concerning the development of direct cathodic SWV and adsorptive stripping SWV methods the neutral&nbsp; and slightly alkaline media were suitable as pH 7.0 with E_p at -1.67 V vs.&nbsp; SCE for ROX and EES and pH 7.2 and pH 7.4 with E_p at -1.85 V and -1.64 V vs. SCE for AZI and CLA, respectively. Based on the cyclic voltammograms recorded at these pH values, adsorptioncontrolled electrode kinetics process can be proposed for all four investigated compounds. The water suppressed ¹H NMR measurements in the pH range between 6.0 and 10.5 indicated that the macrolide molecules at the optimal analytical conditions are predominantly in protonated form via their tertiary amino groups which supported in all four cases their adsorption on the appropriately polarized Hg(Ag)FE electrode. The optimized direct cathodic SWV methods showed good linearity in concentration ranges 4.81-23.3 &mu;g mL^-1, 4.53-29.8 &mu;g mL^-1, 1.96-28.6&nbsp; &mu;g mL^-1, and 1.48-25.9 &mu;g mL^-1 for AZI, EES, CLA and ROX, respectively. The SW-AdSV methods resulted in the linear responses at lower concentration ranges as 1.0-2.46 &mu;g mL^-1, 0.69- 2.44 &mu;g mL^-1, 0.05-0.99 &mu;g mL^-1 and 0.10-0.99 &mu;g mL^-1, for AZI, EES, CLA and ROX, respectively. The RSD for all developed methods was not higher than 1.5% except the SWV method for AZI with 4.7%. The direct cathodic SWV method was successfully applied for the determination of EES in the pharmaceutical preparation Eritromicin^&reg;, while SW-AdSV was tested in the case of the spiked urine sample and for determination of ROX in pharmaceutical preparation Runac^&reg;. In all above cases, the standard addition method was used. The reliability and accuracy of the above procedures in the case of EES determination in model system and pharmaceutical preparation Eritromicin^&reg; were validated by comparing them with those obtained by means of HPLC-DAD measurements.</p><p>After initial study of 3-dehydro-deoxycholic acid/3-dehydro-deoxycholate by glassy carbon electrode, where the absence of any reduction peak was observed in the Britton-Robinson buffer solutions between pH 5.0 and 11.8 by direct cathodic SWV, a bismuth-film was electrodeposited ex situ on the same glassy carbon electrode surface (BiF-GCE) from the usually used plating solution (0.02 mol L^-1 Bi(NO₃)₃, 1.0 mol L^-1 HCl and 0.5 mol L^-1 KBr) and such prepared film-electrode was applied for the characterization and determination of the the target analyte in alkaline media. The reduction signal of analytical importance was observed only by BiF-GCE in Britton-Robinson buffer solutions with pH values between 9.5 and 11.8 in adsorptive stripping square-wave voltammetry working regime, while in the case of the direct cathodic SWV experimental protocol only a very poor reduction peak was obtained. The optimized experimental conditions for the 3-dehydro-deoxycholate determination consist of the optimized electrode conditioning including the electrochemical cycling of the <em>ex situ </em>prepared BiF-GCE potentials in the potential span between -1.0 and -2.0 V vs. SCE (nearly 15 times) in the Britton-Robinson supporting electrolyte pH 11.8 till the stabilization of the baseline current, and the application of two key parameters of the adsorptive square-wave voltammetric protocol: the accumulation time as 30 s and accumulation potential as -1.0 V vs. SCE. Because of the relative asymmetry of the obtained reduction signals of the target analyte with peak E_p at -1.35 V vs. SCE, which is still present in the case of the SW-AdSV, the quantification of the target analyte was based on the linear correlation between peak area of the reduction signal and its appropriate concentrations, and reached limit of detection is 1.43 &mu;g mL^-1 and with two linear ranges of calibration curve from 4,76 &mu;g mL^-1 to 13.0 &mu;g mL^-1 and from 13,0 &mu;g mL^-1 to 23,1 &mu;g mL^-1 for the development of analytical method. The RSD of the method&nbsp; was 3.22%. Additional experiments were performed applying GCE with rectangular form (area 35.32 cm²) modified with ex situ prepared bismuth-film for the electrolysis of the target analyte which was performed at the potential -1.55 V (nearly the peak maxima of the target analyte) vs. SCE. The solution of interest was sampled at the beginning of the experiment, after 2.5 h and after 4.5 h of treatment. Such samples were analysed by simply water suppressing ¹H NMR measurements in the buffered solution at pH 11.8. It can be assumed that during electrolysis of 3-dehydrodeoxycholate the reduction of the keto group present in the structure of the target analyte can be occurred.</p><p>Driven by earlier literature data about the fact that some of the target macrolide antibiotics as e.g. azithromycin showed oxidation behavior at a carbon paste and gold working electrodes detailed characterization and determination of four target macrolide antibiotics were performed on classical carbon paste electrode (CPE) constituted only from graphite powder and paraffin oil with optimized direct anodic SWV methods. In the cases of EES and AZI differential pulse voltammetric (DPV) methods were tested for the same purpose as well. The key parameter in the case of the development of the analytical voltammetric methods is the selection of the pH value of the supporting electrolyte where the shape/simmetry and intensity of the oxidation peak were the criteria. As the appropriate pH value for determination of EES by SWV method the pH 8.0 was selected with E_p at 0.83 V vs. SCE while in the case of the DPV method the pH 12.0 with E_p at 0.55 V vs. SCE was the most suitable for analytical&nbsp; purpose. As for AZI determination, in the case of both SWV and DPV methods the pH 7.0 was the most appropriate supporting electrolyte with the Ep of analytical signal at 0.85 V and 0.80 V vs. SCE, respectively, while in the case of CLA and ROX which were investigated only with SWV method for the analytical purposes the pH 12.0 was the most suitable with E_p at 0.65 V and at 0.63 V vs. SCE. The obtained detection limits applying the bare CPE and the direct anodic SWV are mainly&nbsp; in submicrogram concentration range as 0.17 &mu;g mL^-1; 0.32 &mu;g mL^-1 and 0.30 &mu;g mL^-1 for EES, AZI, and ROX and in the low microgram concentration range as 1.43 &mu;g mL^-1 for the CLA, respectively. The developed method succesfully tested for the determination of ROX in the commercial formulation, Runac^&reg; tablet. In the case of the optimized DPV methods the obtained detection limits for EES and AZI are in the low microgram concentration range 1.03 &mu;g mL^-1 and 1.53 &mu;g mL^-1, respectively. For the improvement of the sensitivity for AZI the DPV method was tested in combination with a&nbsp; CPE working electrode surface modified with gold nanoparticles with diameter of 10 nm (Au-CPE) and reached the limit of detection was 0.95 &mu;g mL^-1 at E_p of 0.80 V vs. SCE. The RSD of the method in the case of the Au-CPE is 3.5% while in the case of the native CPE 6.0%. The linearity of the Au-CPE based analytical method is twice wider then it is case with the bare CPE applying protocol.</p><p>Based on the obtained results it can be conclude that the appropriate combination of the optimized voltammetric pulse techniques and the environmentally friendly and easy to use working electrodes as Hg(Ag)FE, BiF-GCE and CPE together with Au-CPE resulted in the development of reliable analytical method either in the oxidation or reduction studies, often allowing trace level determination of pharmacological importance target analytes in simpler and in some case complexes systems.</p>