Includes vita. / Title from PDF of title page. / Document formatted into pages; contains 204 pages. / Thesis (Ph.D.)--University of South Florida, 2003. / Includes bibliographical references. / Text (Electronic thesis) in PDF format. / ABSTRACT: The goal of this research project was to contribute to the understanding of CuGaSe2/CdS photovoltaic devices, and to improve the performance of these devices. The initial part of the research dealt with the optimization of a Sequential Deposition process for CuIn(Ga)Se2 absorber formation. As an extension of this, a recipe (Type I Process) for CuGaSe2 absorber layer fabrication was developed, and the deposition parameters were optimized. Electrical characterization of the thin films and completed devices was carried out using techniques such as Two-Probe and Three-Probe Current-Voltage, Capacitance-Frequency, Capacitance-Voltage, and Spectral Response measurements. Structural/chemical characterization was done using XRD and EDS analysis. Current densities of up to 15.2 mA/cm2, and Fill Factors of up to 58% were obtained using the Type I CuGaSe2 Process. VOC's, however, were limited to less than 700 mV. / ABSTRACT: Several process variations, such as changes in the rate/order/temperature of depositions and changes in the thickness of layers, resulted in little improvement. With the aim of breaking through this VOC performance ceiling, a new absorber recipe (Type II Process) was developed. VOC's of up to 735 mV without annealing, and those of up to 775 mV after annealing, were observed. Fill Factors were comparable to those obtained with Type I Process, whereas the Current Densities were found to be reduced (typically, 10-12 mA/cm2, with the best value of 12.6 mA/cm2). This performance of Type II devices was correlated to a better intermixing of the elements during the absorber formation. To gain an understanding of the performance limitations, two simulation techniques, viz. SCAPS and AMPS, were used to model our devices. / ABSTRACT: Several processing experiments and SCAPS modeling indicate that a defective interface between CuGaSe2 and CdS, and perhaps a defective absorber layer, are the cause of the VOC limitation. AMPS simulation studies, on the other hand, suggest that the back contact is limiting the performance. Attempts to change the physical back contact, by changes in the absorber processing, were unsuccessful. Processing experiments and simulations also suggest that the CuGaSe2/CdS solar cell involves a true heterojunction between these two layers. / System requirements: World Wide Web browser and PDF reader. / Mode of access: World Wide Web.

Traditional sources of electrical energy are finite and can produce significant pollution. Solar cells produce clean energy from incident sunlight, and will be an important part of our energy future. A new nanostructured extremely thin absorber solar cell with 0.98% power conversion efficiency and maximum external quantum efficiency of 61% at 650 nm has been fabricated and characterized. This solar cell is composed of a fluorine-doped tin oxide base layer, n-type aluminum doped zinc oxide nanowires, a cadmium selenide absorber layer, poly(3-hexylthiophene) as a p-type layer, and thermally evaporated gold as a back contact. Zinc oxide nanowire electrodeposition has been investigated for different electrical environments, and the role of a zinc oxide thin film layer has been established. Cadmium selenide nanoparticles have been produced and optimized in-house and compared to commercially produced nanoparticles. Argon plasma cleaning has been investigated as a method to improve electronic behavior at cadmium selenide interfaces. The thermal anneal process for cadmium selenide nanoparticles has been studied, and a laser anneal process has been investigated. It has been found that the most efficient solar cells in this study are produced with a zinc oxide thin film, zinc oxide nanowires grown under constant -1V bias between the substrate material and the anode, cadmium selenide nanoparticles purchased commercially and annealed for 24 hours in the presence of cadmium chloride, and high molecular weight poly(3-hexylthiophene) spin-coated in a nitrogen environment.

A new approach to the discovery of high absorbing semiconductors for solar cells was taken by working under a set of design principles and taking a systemic methodology. Three transition metal chalcogenides at varying states of development were evaluated within this framework. Iron pyrite (FeS���) is well known to demonstrate excellent absorption, but the coexistence with metallic iron sulfides was found to disrupt its semiconducting properties. Manganese diselenide (MnSe���), a material heavily researched for its magnetic properties, is proposed as a high absorbing alternative to iron pyrite that lacks destructive impurity phases. For the first time, a MnSe��� thin film was synthesized and the optical properties were characterized. Finally, CuTaS���, a known but never characterized material, is also proposed as a high absorbing semiconductor based on the design principles and experimental results. / Graduation date: 2013