- About
-
The Global ETD Search service is a free service for researchers
to find electronic theses and dissertations. This service is
provided by the
Networked Digital Library of Theses and Dissertations.
Our metadata is collected from universities around the world. If you manage a university/consortium/country archive and want to be added, details can be found on the NDLTD website.
Search results
Showing 81 to 90 of 1231 (0.049 seconds)Spelling suggestions: "subject:"solar energy."" "subject:"polar energy.""
| 81 |
Optimization of Solar power production using heat engines.Selçuk, M. Kudret. January 1969 (has links)
No description available.
|
| 82 |
Design, development, and evaluation of a heat exchanger for a linear fixed mirror solar concentratorMcKee, Michael Ellis 08 1900 (has links)
No description available.
|
| 83 |
General design of a solar power system using the principle of energy availabilityLee, Chien Kuo 12 1900 (has links)
No description available.
|
| 84 |
Optical performance of paraboloidal solar concentrating collectorsWhite, Timothy Andrew 08 1900 (has links)
No description available.
|
| 85 |
Optical analysis of cavity solar energy receiversWigginton, James Michael 05 1900 (has links)
No description available.
|
| 86 |
Investigation of the dependence of atmospheric transmittance for beam radiation on clearness indexBalaras, Constantinos Agelou 05 1900 (has links)
No description available.
|
| 87 |
The preparation and properties of ITO/tin/silicon solar cellsMulyadi, Rachmat January 1989 (has links)
Transparent semiconducting oxide films of ITO have been deposited using screen printing techniques for fabricating heterostructure solar cells. The ITO material used is a readymade combination of organometallic compounds of indium and tin, dissolved in a suitable organic vehicle to make a screenprintable ink or paste. The paste is then printed onto substrates in the desired configurations. The effect of various firing temperatures, from 450°C to 650 °c, on the film properties were observed. The sheet resistances, Ra, changed as the firing temperature varied. Ra values could be decreased by annealing the films in an inert gas or in vacuum conditions. An annealing temperature of 300°C seemed to be optimum for annealing the ITO films. This decreased the sheet resistance by a factor of more than ten. The lowest sheet resistance of the ITO films was about 290 n/sq, measured during annealing under vacuum conditions at a temperature of 300 °C. This gradually increased up to about 1 Kn/sq after the film was aged for a few days in a laboratory atmosphere. The solar cell structures of ITO/p-Si and ITO/Sn/p-Si were made in this research. The first structure suffered from an excessive oxide interfacial layer thickness and it was abandoned. The second structure was then made to overcome the problems resulting from the interfacial oxide. The Sn layer was produced by using evaporation prior to the screen printing of ITO. The thickness of the Sn layer was about 100 nm. After evaporation, screen printing methods were used to complete the heterostructure solar cell. The best typical values of these cells are, open circuit voltage, V~= 0.360 Volt, short circuit current density, Jsc= 16.4 mA/cm2 with fill factor, FF = 0.34 and efficiency, 1) = 2.5% under 80 mW/cm2 simulated illumination, where this illumination is equivalent to air mass 2, (AM2).
|
| 88 |
Solar heating for swimming pools with special reference to ground collectorsRawlings, R. H. D. January 1983 (has links)
No description available.
|
| 89 |
Multilayer solar air heater and the development of small scale maize dryer for village use in KenyaOthieno, A. January 1983 (has links)
No description available.
|
| 90 |
Photovoltaic cells for solar concentration : A theoretical analysis of multi-cell systemsBaird, A. M. January 1983 (has links)
No description available.
|
Page generated in 0.0556 seconds