Seismic design criteria have been heavily improved by the Federal Emergency Management Agency (FEMA) after the Northridge CA earthquake in 1994. Most of the damage observed was caused by brittle failure of moment frame connections. This failure was induced by the formation of the plastic hinge at undesirable locations in the beam and the column near the connection. Using welded flange plate (WFP) connections will force the formation of the plastic hinge away from the face of the column while preventing the brittle failure of the moment connection. FEMA-350 design criteria recommendations for WFP connections suggest that the plastic hinge will form away from the face of the column directly under the cover plate. The purpose of this research is to prove that the plastic hinge will form away from the face of the column, at a distance of approximately half the depth of the beam away from the cover plate. The further away the plastic hinge is from the face of the column the higher the connection demands. Therefore, underestimating the location of the plastic hinge could lead to under designed connections. The modeling and analysis of WFP connections was performed using finite element analysis software. A total of eight models with half beam half column configuration were considered in this study. Each selected section of beam and column was first designed, modeled and analyzed using WFP connections design recommendations from FEMA-350, with calculations modifications to account for the proposed plastic hinge location. Results were computed and comparisons were made in terms of plastic hinge location from the cover plates. Strength obtained for each model using finite element analysis software was also compared with hand calculations. This research also proves that increasing the thickness of the cover plates will generate an increase in the connection capacity and strength.

Steel moment frames are a popular seismic-force resisting system, but it is believed that they are susceptible to early fracture if there is a stress concentration in the plastic hinge region, also known as the protected zone. If a defect is present in this area, it may be repaired by grinding and/or welding, but little research has investigated how the repairs affect the performance of full-scale moment connections subjected to inelastic rotations. Thus, the goals of this research were to establish the performance of full-scale moment connections with repairs and defects, then develop a method for predicting fracture of the full-scale specimens using more economical cyclic bend tests. To do this, six full-scale reduced beam section (RBS) connections were tested having arrays of repairs or defects applied to the flanges. The repairs were 0.125 in. deep notches ground to a smooth taper and 0.25 in. deep notches ground to a smooth taper, welded, and ground smooth. The defects were sharp 0.25 in. and 0.375 in. notches. In addition, 54 bend tests were conducted on beam flange and bar stock coupons having the same repairs and defects, power actuated fasteners, puddle welds, and no artifacts. Finally, Coffin-Manson low-cycle fatigue relationships were calibrated using results from the cyclic bend tests with each artifact (repair, defect, or attachment method) and used in conjunction with estimates of full-scale plastic strain amplitudes to predict fracture of full-scale specimens. All four of the full-scale moment connections with repairs satisfied special moment frame qualification criteria (SMF). One full-scale specimen with sharp 0.25 in. notches satisfied SMF qualification criteria, but the flexural resistance dropped rapidly after the qualification cycle. On the other hand, the specimen with sharp 0.375 in. notches did not satisfy SMF qualification criteria due to ductile fractures propagating from the notches. The proposed method for predicting fracture of full-scale connections was validated using the six current and six previous full-scale RBS specimens. This method underpredicted fracture for eleven of the twelve specimens. The ratio of the actual to predicted cumulative story drift at fracture had a mean of 1.13 and a standard deviation of 0.19. / M.S. / Moment connections in steel structures resist earthquake loads by permanently deforming the material near the connection. This area is called the protected zone and is critical to the safety of the structure in an earthquake. Due to this importance, no defects are allowed near the connection, which can include gouges or notches. If a defect does occur, it must repaired by a grinding or welding. These are the required repair methods, but there have be no tests to determine how the repairs affect the strength and ductility of the connection. This research tested six full-scale moment connections with defects repaired by grinding and welding, as well as unrepaired defects. A correlation was also developed and validated between the full-scale tests and small-scale bend tests of steel bars with the same defects and repairs. This relationship is valuable because the small-scale tests are quicker and less expensive to conduct than the full-scale tests, meaning other defects or repairs could be easily tested in the future. All but one of the six full-scale specimens met the strength requirements and had adequate ductility. The one test specimen that failed had an unrepaired defect. The relationship between the full-scale and small-scale tests underpredicted fracture (a conservative estimate) for the five of the full-scale tests and overpredicted fracture (unconservative estimate) for one test.

In practice, steel frames are analyzed and designed by assuming all beam to column connections as either rigid or simple. In real life, there are no such idealizations as rigid or simple and all connections would actually belong to a group of connections named as semi rigid connections. Various difficulties exist in modeling an accurate non-linear behavior of a steel structure, where one of these challenges is the modeling of semi-rigid behavior of connections. A detailed finite element model would take into account the complex interaction between all surfaces due to contact, friction and bolt pretension besides the material and geometrical nonlinearity effects. All these nonlinearity effects could be simply lumped as a moment-rotation type model at the connection region. Such a methodology is followed in this thesis and the main aim is to study the lumped nonlinear behavior of steel semi-rigid connections on the overall structural responses of steel Special Moment Frames. In this thesis three, nine and fifteen story steel Special Moment Frames are analyzed and designed as rigid frames first, and then the frames are reanalyzed considering non-linear effects due to semi-rigid connections. Changes in the ductility and overstrength reduction factors obtained from pushover curves are compared between the rigid and semi rigid modeling alternatives.

Master of Science / Department of Architectural Engineering and Construction Science / Kimberly W. Kramer / Of seismic steel lateral force resisting systems in practice today, the Moment Frame has most diverse connection types. Special Moment frames resist lateral loads through energy dissipation of the inelastic deformation of the beam members. The 1994 Northridge earthquake proved that the standard for welded beam-column connections were not sufficient to prevent damage to the connection or failure of the connection. Through numerous studies, new methods and standards for Special Moment Frame connections are presented in the Seismic Design Manual 2nd Edition to promote energy dissipation away from the beam-column connection. A common type of SMF is the Reduce Beams Section (RBS). To encourage inelastic deformation away from the beam-column connection, the beam flange’s dimensions are reduced a distance away from the beam-column connection; making the member “weaker” at that specific location dictating where the plastic hinging will occur during a seismic event. The reduction is usually taken in a semi-circular pattern. Another type of SMF connection is the Kaiser Bolted Bracket® (KBB) which consists of brackets that stiffen the beam-column connection. KBB connections are similar to RBS connections as the stiffness is higher near the connection and lower away from the connection. Instead of reducing the beam’s sectional properties, KBB uses a bracket to stiffen the connection. The building used in this parametric study is a 4-story office building. This thesis reports the results of the parametric study by comparing two SMF connections: Reduced Beam Section and Kaiser Bolted Brackets. This parametric study includes results from three Seismic Design Categories; B, C, and D, and the use of two different foundation connections; fixed and pinned. The purpose of this parametric study is to compare member sizes, member forces, and story drift. The results of Seismic Design Category D are discussed in depth in this thesis, while the results of Seismic Design Category B and C are provided in the Appendices.

This study investigates the influence of the gravity load resisting system on the collapse performance of Special Steel Moment Frames (SMFs). The influence was quantified using the FEMA P-695 methodology. The buildings used for this study were a 2-, 4- and 8-story SMFs taken from the ATC76-1 project where their collapse performance was already evaluated without the gravity system. The main work of this dissertation has been divided in two parts. The first part studies the influence of the gravity system when it is incorporated explicitly as part of the lateral resisting system. Aspects of the gravity frame that were investigated include the contribution of stiffness and strength of beam to column connections, and the location of splices in the gravity columns. Moreover, this research investigates the potential for the development of inelastic deformations in the gravity columns, and the effect of such deformations on structural response. The results show that gravity connections and gravity column's continuity profoundly affect the computed response and collapse probability. The inelastic behavior in gravity columns has a less important effect but should be included in the analysis. The second part of the investigation looks more in depth at the role of the gravity columns on the collapse performance of SMFs. Using the 2-, 4- and 8-story SMFs, the gravity columns are incorporated using the approach where all the gravity columns are lumped into one elastic, pinned at the base and continuous element. The approach is first validated by checking different aspects such as: strength of gravity connections to induce yielding into gravity columns, difference between the explicit and lumping column approach, and required gravity column's splices to provide continuity. The stiffness of the element representing the gravity columns was varied in order to find the influence of the gravity columns. At the end of the study it was found that they have a significant influence on the collapse performance of SMFs, especially on taller structures like the 8-story model. Moreover it was concluded that an adequate stiffness of the gravity columns could be found by performing nonlinear static pushover analysis. / Ph. D.

No description available.

In this thesis, the optimum design algorithm is presented for reinforced concrete special moment frames. The objective function is considered as the total cost of reinforced concrete frame which includes the cost of concrete, formwork and reinforcing steel bars. The cost of any component is inclusive of material, fabrication and labor. The design variables in beams are selected as the width and the depth of beams in each span, the diameter and the number of longitudinal reinforcement bars along the span and supports. In columns the width and the depth of the column section, the number and the diameter of bars in x and y directions are selected as design variables. The column section database is prepared which includes the width and height of column section, the diameter and the number of reinforcing bars in the column section is constructed. This database is used by the design algorithm to select appropriate sections for the columns of the frame under consideration. The design constraints are implemented from ACI 318-05 which covers the flexural and shear strength, serviceability, the minimum and maximum steel percentage for flexural and shear reinforcement, the spacing requirements for the reinforcing bars and the upper and lower bound requirements for the concrete sections. The optimum design problem formulated according to ACI 318-05 provisions with the design variables mentioned above turns out to be a combinatorial optimization problem. The solution of the design problem is obtained by using the harmony search algorithm (HS) which is one of the recent additions to meta-heuristic optimization techniques which are widely used in obtaining the solution of combinatorial optimization problems. The HS algorithm is quite simple and has few parameters to initialize and consists of simple steps which make it easy to implement. Number of design examples is presented to demonstrate the efficiency and robustness of the optimum design algorithm developed.

A number of recent research studies have investigated the performance of panel zones in seismic-resistant steel Special Moment Resisting Frames (SMF). These recent studies investigated various options for attaching doubler plates to the column at beam-column joints in SMF for purpose of increasing the shear strength of the panel zone. This previous work was primarily focused on doubler plates that extend beyond the top and bottom of the attached beams, and considered cases both with and without continuity plates. As an extension to this previous research, this thesis explores the situation when a doubler plate is fitted between the continuity plates. The objective of this research was to evaluate various options for welding fitted doubler plates to the column and continuity plates through the use of finite element analysis, and to provide recommendations for design. The development and validation of the finite element model are described, along with the results of an extensive series of parametric studies on various panel zone configurations and attachment details for fitted doubler plates. Based on the results of these analyses, recommendations are provided for design of welds used for attaching fitted doubler plates in the panel zone of SMF systems. / text