Yes / This paper evaluates the influence of mineral admixtures partially replacing cement, sea sand replacing quartz, sea water replacing fresh water on ultra-high performance concrete (UHPC). The fluidity and mechanical properties were studied. Besides, the impermeability, chloride resistance and freeze-thaw resistance were investigated. Failure modes, scanning electron microscope (SEM) analysis, mass loss, relative dynamic modulus of elasticity and mechanical properties of UHPCs after freeze-thaw cycles were conducted. The results showed the fluidity of UHPC paste gradually increases with the improvement of water-binder ratio. It is recommended that the water-binder ratio of UHPC be set at 0.19. The fluidity also increases with the improvement of the content of slag, fly ash and water reducer, but decreases with the improvement of silica fume content. The flexural and compressive strengths of UHPC enhance with the improvement of the content of silica fume, but reduce with the improvement of the content of fly ash and slag. The UHPCs made of quartz sand, river sand and sea sand, all, achieve a high strength. UHPCs prepared at standard curing conditions, with or without steel fibers, mixed by artificial seawater and made of sea sand, exhibited excellent impermeability and chloride resistance. The frost resistant grade of all UHPC specimens prepared by standard curing are greater than F500 exhibiting excellent freeze-thaw resistance and sustainability.

Yes / Considering the continuous development of sustainable development, energy saving, and emission reduction concepts, it is very important to reduce concrete's cement content in order to improve its environmental impact. Using reactive admixture to replace part of the cement in ultra-high performance concrete (UHPC) can effectively improve the overall performance of the concrete and reduce carbon dioxide emissions (CO2), which is an important aspect of environmental protection. Here, industrial waste residue (fly ash and slag), sea sand (SS), and manufactured sand (MS) were used to produce UHPC under standard curing condition, to reduce the material cost and make the it more environmentally friendly and sustainable. The effects of water-binder ratio, contents of cementitious materials, types of sands, and content of steel fibers on the mechanical performance of UHPC under standard curing were investigated experimentally. In addition, the effects of various factors on the depth under hydraulic pressure and electric flux of UHPC, mass loss, relative dynamic modulus of elasticity, flexural, and compressive strengths of UHPC specimens after freeze-thaw cycles were conducted to evaluate the impermeability, chloride, and freeze-thaw resistance of various UHPCs produced. The obtained experimental results show that the SS-UHPC and MS-UHPC prepared by standard curing exhibit high strength, excellent impermeability, and chloride resistance. The frost resistant grade of all groups of UHPCs prepared by standard curing are greater than F500 and had excellent freeze-thaw resistance, including those produced with local tap water or artificial seawater. The investigation presented in this paper could contribute to the production of new UHPCs of low cost and environmental-friendly and accelerate the application of UHPC in engineering structures.

Yes / Considering the continuous development of sustainable development, energy saving, and emission reduction concepts, it is very important to reduce concrete's cement content in order to improve its environmental impact. Using a reactive admixture to replace part of the cement in ultra-high-performance concrete (UHPC) can effectively improve the overall performance of the concrete and reduce carbon dioxide emissions, which is an important aspect of environmental protection. Here, industrial waste residue (fly ash and slag), sea sand (SS), and manufactured sand (MS) were used to produce UHPC under standard curing conditions to reduce the material cost and make it more environmentally friendly and sustainable. The effects of water-binder ratio, contents of cementitious materials, types of sands, and content of steel fibers on the mechanical performance of UHPC under standard curing were investigated experimentally. In addition, evaluations of the impermeability, chloride, and freeze-thaw resistance of various UHPCs produced were conducted by investigating the effects of various factors on the depth under hydraulic pressure and electric flux of UHPC, as well as the mass loss, relative dynamic modulus of elasticity, flexural strength, and compressive strength of UHPC specimens after freeze-thaw cycles. The obtained experimental results show that the SS-UHPC and MS-UHPC prepared by standard curing exhibit high strength, excellent impermeability, and chloride resistance. The frost-resistant grade of all groups of UHPCs prepared by standard curing was greater than F500 and had excellent freeze-thaw resistance, including those produced with local tap water or artificial seawater. The investigation presented in this paper could contribute to the production of new low-cost and environmentally friendly UHPCs and accelerate the application of UHPC in engineering structures.