With the fast development of communication systems, computers and consumer electronics, the power supplies for telecoms, servers, desktops, laptops, flat-panel TVs, LED lighting, etc. are required for more power delivery with smaller spaces. The LLC resonant converter has been widely adopted for these applications due to the advantages in high efficiency, high power density and holdup time operation capability. However, unlike PWM converters, the control of the LLC resonant converter is much more difficult because of the fast dynamic characteristic of the resonant tank. In some highly dynamic processes like the load transient, start-up, over-load protection and burst operation, it is hard to control the current and voltage stresses and oscillations in the resonant tank. Moreover, to meet the high power density requirement, the LLC is required to operate at a high switching frequency. Thus the driving of the synchronous rectifier (SR) poses a design challenge as well. To analyze the fast dynamic characteristic, a graphic state-plane technique has been adopted for a class of resonant converters. In this work, it has been extended to the LLC resonant converter. First of all, the LLC steady state and dynamic behaviors are analyzed in the state plane. After that, a simplified implementation of the optimal trajectory control is proposed to significantly improve the load transient response: the new steady state can be tracked in the minimal period of time. With the advantages of the state-trajectory analysis and digital control, the LLC soft start-up is optimized as well. The current and voltage stress is limited in the resonant tank during the start-up process. The output voltage is built up quickly and smoothly. Furthermore, the LLC burst mode is investigated and optimized in the state plane. Several optimal switching patterns are proposed to improve the light load efficiency and minimize the dynamic oscillations. During the burst on-time, the LLC can be controlled to track the steady state of the best efficiency load condition in one-pulse time. Thus, high light-load efficiency is accomplished. Finally, an intelligent SR driving scheme is proposed and its simple digital implementation is introduced. By sensing the SR drain to source voltage and detecting the paralleled body diode conduction, the SR gate driving signal can be tuned within all operating frequency regions. In conclusion, this work not only solves some major academic problems about analysis and control of the LLC resonant converter based on the graphic state plane, but also makes significant contributions to the industry by improving the LLC transient responses and overall efficiency. / Ph. D.

For the future of sustainable energy, renewable energy will need to significantly penetrate existing utility grids. While various renewable energy sources are networked with high-voltage DC grids, integration between these high-voltage DC grids and the existing AC grids is a significant technical challenge. Among the limited choices available, the modular multi-level converter (MMC) is the most prominent interface converter used between the DC and AC grids. This subject has been widely pursued in recent years. One of the important design challenges when using an MMC is to reduce the capacitor size associated with each module. Currently, a rather large capacitor bank is required to store a certain amount of line-frequency related circulating energy. Several control strategies have been introduced to reduce the capacitor voltage ripples by injecting certain harmonic current. Most of these strategies were developed using trial and error and there is a lack of a systematic means to address this issue. Most recently, Yadong Lyu has proposed to control the modulation index in order to reduce capacitor ripples. The total elimination of the unwanted circulating power associated with both the fundamental line frequency and the second-order harmonic was demonstrated, and this resulted in a dramatic reduction in capacitor size. To gain a better understanding of the intricate operation of the MMC, this thesis proposes a state-space analysis technique in the present paper. Combining the power flow analysis with the state trajectory portrayed on a set of two-dimensional state plans, it clearly delineates the desired power transfer from the unwanted circulating energy, thus leading to an ultimate reduction in the circulation energy and therefore the required capacitor volume. / Master of Science

The modular multi-level converter (MMC) is the most prominent interface converter used between the HVDC grid and the HVAC grid. One of the important design challenges in MMC is to reduce the capacitor size. In the current practice, a rather large capacitor bank is required to store line-frequency related circulating energy, even though a number of control strategies have been introduced to reduce the capacitor voltage ripples. In the present paper, a novel control strategy is proposed by means of harmonic injections in conjunction with gain control to completely eliminate both the line frequency and the second-order harmonic of the capacitor voltage ripple. Ideally, the proposed method works with the full bridge topology. However, the concept also works with half bridge topology with a significant reduction of line frequency related ripple. To gain a better understanding of the nature of circulating energy and the means of reducing it, the method of state plane analysis is employed to offer visual support. In addition, the design trade-off between full bridge MMC and half bridge MMC is presented and a novel control strategy for a hybrid MMC is proposed. Finally, the work is supported with a scaled down hardware demonstration. / Master of Science