The first part of the thesis addresses the fatigue performance of concrete bridge decks with GFRP stay-in-place structural forms replacing the bottom layer of rebar. The forms were either flat plate with T-up ribs joined using lap splices, or corrugated forms joined through pin-and-eye connections. The decks were supported by simulated Type III precast AASHTO girders spaced at 1775mm (6ft.). Two surface preparations were examined for each GFRP form, either using adhesive coating that bonds to freshly cast concrete, or simply cleaning the surface before casting. For the bonded deck with flat-ribbed forms, adhesive bond and mechanical fasteners were used at the lap splice, whereas the lap splice of the unbonded deck had no adhesive or fasteners. All the decks survived 3M cycles at 123kN service load of CL625 CHBDC design truck. The bonded flat-ribbed-form deck survived an additional 2M cycles at a higher load simulating a larger girder spacing of 8ft. Stiffness degradations were 9-33% with more reduction in the unbonded specimens. Nonetheless, live load deflections of all specimens remained below span/1600. The residual ultimate strengths after fatigue were reduced by 5% and 27% for the flat-ribbed and corrugated forms, respectively, but remained 7 and 3 times higher than service load. The second part of the thesis investigates the performance of bridge deck overhangs reinforced by GFRP rebar. Overhangs of full composite slab-on-girder bridge decks at 1:2.75 scale were tested monotonically under an AASHTO tire pad. Five tests were conducted on overhangs of two lengths: 260mm and 516mm, representing scaled overhangs of 6ft. and 8ft. girder spacing, respectively. The 260mm overhang was completely reinforced with GFRP rebar while the 516mm overhang consisted of a GFRP-reinforced section and a steel-reinforced section. The peak loads were approximately 2 to 3 times the established equivalent service load of 24.3kN, even though the overhangs were not designed for flexure according to the CHBDC but rather with lighter minimum reinforcement in anticipation of shear failure. The failure mode Abstract ii of each overhang section was punching shear. The steel-reinforced overhang section exhibited a greater peak load capacity (13.5%) and greater deformability (35%) when compared to the GFRP-reinforced overhang section. / Thesis (Master, Civil Engineering) -- Queen's University, 2013-09-17 18:54:18.131

This study presents a conceptual design process for one-way reinforced concrete slabs cast over Textile Reinforced Concrete (TRC) Stay-in-Place (SiP) formwork elements, aiming at the minimization of the composite slab cost satisfying Ultimate Limit State (ULS) and Serviceability Limit State (SLS) design criteria. The thin-walled TRC element is considered to participate in the structural behaviour of the composite slab. This distinct function of the TRC element (as formwork and as a part of a composite element) distinguishes the design procedure into two States: a Temporary and a Permanent one. Design parameters such as the type of the textile reinforcement (material), the geometry of the TRC cross-section, the flexural strength of the fine-grained concrete in the TRC element and the compressive strength of the cast in-situ concrete are considered as the main optimization variables.

Performance of bridges during previous earthquakes has demonstrated that many structural failures could be attributed to seismic deficiencies in bridge columns. Lack of transverse reinforcement and inadequate splicing of longitudinal reinforcement in potential plastic hinge regions of columns constitute primary reasons for their poor performance. A number of column retrofit techniques have been developed and tested in the past. These techniques include steel jacketing, reinforced concrete jacketing and use of transverse prestressing (RetroBelt) for concrete confinement, shear strengthening and splice clamping. A new retrofit technique, involving fibre reinforced polymer (FRP) jacketing has emerged as a convenient and structurally sound alternative with improved durability. The new technique, although received acceptance in the construction industry, needs to be fully developed as a viable seismic retrofit methodology, supported by reliable design and construction procedures. The successful application of externally applied FRP jackets to existing columns, coupled with deteriorating bridge infrastructure, raised the possibility of using FRP reinforcement for new construction. Stay-in-place formwork, in the form of FRP tubes are being researched for its feasibility. The FRP stay-in-place tubes offer ease in construction, convenient formwork, and when left in place, the protection of concrete against environmental effects, including the protection of steel reinforcement against corrosion, while also serving as column transverse reinforcement. Combined experimental and analytical research was conducted in the current project to i) improve the performance of FRP column jacketing for existing bridge columns, and ii) to develop FRP stay-in-place formwork for new bridge columns. The experimental phase consisted of design, construction and testing of 7 full-scale reinforced concrete bridge columns under simulated seismic loading. The columns represented both existing seismically deficient bridge columns, and new columns in stay-in-place formwork. The existing columns were deficient in either shear, or flexure, where the flexural deficiencies stemmed from lack of concrete confinement and/or use of inadequately spliced longitudinal reinforcement. The test parameters included cross-sectional shape (circular or square), reinforcement splicing, column shear span for flexure and shear-dominant behaviour, FRP jacket thickness, as well as use of FRP tubes as stay-in-place formwork, with or without internally embedded FRP crossties. The columns were subjected to a constant axial compression and incrementally increasing inelastic deformation reversals. The results, presented and discussed in this thesis, indicate that the FRP retrofit methodology provides significant confinement to circular and square columns, improving column ductility substantially. The FRP jack also improved diagonal tension capacity of columns, changing brittle shear-dominant column behavior to ductile flexure dominant response. The jackets, when the transverse strains are controlled, are able to improve performance of inadequately spliced circular columns, while remain somewhat ineffective in improving the performance of spliced square columns. FRP stay-in-place formwork provides excellent ductility to circular and square columns in new concrete columns, offering tremendous potential for use in practice. The analytical phase of the project demonstrates that the current analytical techniques for column analysis can be used for columns with external FRP reinforcement, provided that appropriate material models are used for confined concrete, FRP composites and reinforcement steel. Plastic analysis for flexure, starting with sectional moment-curvature analysis and continuing into member analysis incorporating the formation of plastic hinging, provide excellent predictions of inelastic force-deformation envelopes of recorded hysteretic behaviour. A displacement based design procedure adapted to FRP jacketed columns, as well as columns in FRP stay-in-place formwork provide a reliable design procedure for both retrofitting existing columns and designing new FRP reinforced concrete columns.

Performance of bridges during previous earthquakes has demonstrated that many structural failures could be attributed to seismic deficiencies in bridge columns. Lack of transverse reinforcement and inadequate splicing of longitudinal reinforcement in potential plastic hinge regions of columns constitute primary reasons for their poor performance. A number of column retrofit techniques have been developed and tested in the past. These techniques include steel jacketing, reinforced concrete jacketing and use of transverse prestressing (RetroBelt) for concrete confinement, shear strengthening and splice clamping. A new retrofit technique, involving fibre reinforced polymer (FRP) jacketing has emerged as a convenient and structurally sound alternative with improved durability. The new technique, although received acceptance in the construction industry, needs to be fully developed as a viable seismic retrofit methodology, supported by reliable design and construction procedures. The successful application of externally applied FRP jackets to existing columns, coupled with deteriorating bridge infrastructure, raised the possibility of using FRP reinforcement for new construction. Stay-in-place formwork, in the form of FRP tubes are being researched for its feasibility. The FRP stay-in-place tubes offer ease in construction, convenient formwork, and when left in place, the protection of concrete against environmental effects, including the protection of steel reinforcement against corrosion, while also serving as column transverse reinforcement. Combined experimental and analytical research was conducted in the current project to i) improve the performance of FRP column jacketing for existing bridge columns, and ii) to develop FRP stay-in-place formwork for new bridge columns. The experimental phase consisted of design, construction and testing of 7 full-scale reinforced concrete bridge columns under simulated seismic loading. The columns represented both existing seismically deficient bridge columns, and new columns in stay-in-place formwork. The existing columns were deficient in either shear, or flexure, where the flexural deficiencies stemmed from lack of concrete confinement and/or use of inadequately spliced longitudinal reinforcement. The test parameters included cross-sectional shape (circular or square), reinforcement splicing, column shear span for flexure and shear-dominant behaviour, FRP jacket thickness, as well as use of FRP tubes as stay-in-place formwork, with or without internally embedded FRP crossties. The columns were subjected to a constant axial compression and incrementally increasing inelastic deformation reversals. The results, presented and discussed in this thesis, indicate that the FRP retrofit methodology provides significant confinement to circular and square columns, improving column ductility substantially. The FRP jack also improved diagonal tension capacity of columns, changing brittle shear-dominant column behavior to ductile flexure dominant response. The jackets, when the transverse strains are controlled, are able to improve performance of inadequately spliced circular columns, while remain somewhat ineffective in improving the performance of spliced square columns. FRP stay-in-place formwork provides excellent ductility to circular and square columns in new concrete columns, offering tremendous potential for use in practice. The analytical phase of the project demonstrates that the current analytical techniques for column analysis can be used for columns with external FRP reinforcement, provided that appropriate material models are used for confined concrete, FRP composites and reinforcement steel. Plastic analysis for flexure, starting with sectional moment-curvature analysis and continuing into member analysis incorporating the formation of plastic hinging, provide excellent predictions of inelastic force-deformation envelopes of recorded hysteretic behaviour. A displacement based design procedure adapted to FRP jacketed columns, as well as columns in FRP stay-in-place formwork provide a reliable design procedure for both retrofitting existing columns and designing new FRP reinforced concrete columns.

This study presents a conceptual design process for one-way reinforced concrete slabs cast over Textile Reinforced Concrete (TRC) Stay-in-Place (SiP) formwork elements, aiming at the minimization of the composite slab cost satisfying Ultimate Limit State (ULS) and Serviceability Limit State (SLS) design criteria. The thin-walled TRC element is considered to participate in the structural behaviour of the composite slab. This distinct function of the TRC element (as formwork and as a part of a composite element) distinguishes the design procedure into two States: a Temporary and a Permanent one. Design parameters such as the type of the textile reinforcement (material), the geometry of the TRC cross-section, the flexural strength of the fine-grained concrete in the TRC element and the compressive strength of the cast in-situ concrete are considered as the main optimization variables.

H αύξηση των περιβαλλοντικών, αισθητικών και λειτουργικών απαιτήσεων που πρέπει να πληρούν οι σύγχρονες κατασκευές Πολιτικού Μηχανικού, σε συνδυασμό με την απαίτηση για συμπίεση του κόστους του κύκλου ζωής τους, οδηγούν στην ανάγκη για τη διερεύνηση της εφαρμογής νέων υλικών και μεθόδων που θα εφαρμοσθούν στη κατασκευή των δομικών έργων. Στην κατεύθυνση αυτή κινούνται οι μέθοδοι κατασκευής δομικών στοιχείων με τη χρήση παραμενόντων τύπων. Η παρούσα Διατριβή πραγματεύεται, τόσο σε αναλυτικό όσο και σε πειραματικό επίπεδο, το σχεδιασμό επίπεδων στοιχείων Ο/Σ που παρασκευάζονται έναντι παραμενόντων τύπων παρασκευασμένων από σύνθετα υλικά τσιμεντοειδούς μήτρας και οπλισμένων με πλέγματα μη μεταλλικών ινών (Ινοπλέγματα σε Ανόργανη Μήτρα-ΙΑΜ). Η Διατριβή αναπτύσσει την διαδικασία σχεδιασμού που προορισμός της είναι να ενσωματωθεί σε έναν αλγόριθμο βέλτιστου σχεδιασμού για την επίτευξη σχεδιαστικών λύσεων που θα αντιστοιχούν στο ελάχιστο κόστος κατασκευής για το σύμμεικτο στοιχείο. Η διαδικασία σχεδιασμού τροφοδοτείται από ένα εκτενές πρόγραμμα πειραματικών δοκιμών. / The continuously raising demands for cost effective and environmental friendly concrete structures which should fulfill also high aesthetic design criteria, lead the Engineers to explore new construction methods and materials. The application of semi-prefabrication techniques, involving the use of participating Stay-in-Place formwork elements seems to be an attractive solution. The present dissertation deals with the experimental and analytical investigation of one-way concrete slabs cast over Stay-In-Place formwork elements produced from cementitious composite materials reinforced with textile structures from non-metallic continuous fibers (Textile Reinforced Concrete). In this dissertation a design procedure for Composite Reinforced Concrete (RC)/TRC one-way slabs is developed. For the development of the design procedure the results from an extensive experimental investigation campaign were exploited. The campaign focused on the mechanical behavior of RC/TRC composite slabs under four point bending. Also tests on the formwork elements under four point bending tests were carried out. Ahead of the bending tests, uniaxial tension tests on dumbbell TRC specimens were conducted in order to characterize this composite material. Finally, the design procedure was integrated on a Genetic Algorithm in order to achieve minimum-cost design solutions.