In this study the plane linear elastic problem of a functionally graded layer which contains periodic cracks is considered. The main objective of this study is to determine the thermal stress intensity factors for edge cracks. In order to find an analytic solution, Young&rsquo / s modulus and thermal conductivity are assumed to be varying exponentially across the thickness, whereas Poisson ratio and thermal diffusivity are taken as constant. First, one dimensional transient and steady state conduction problems are solved (heat flux being across the thickness) to determine the temperature distribution and the thermal stresses in a crack free layer. Then, the thermal stress distributions at the locations of the cracks are applied as crack surface tractions in the elasticity problem to find the stress intensity factors. By defining an appropriate auxiliary variable, elasticity problem is reduced to a singular integral equation, which is solved numerically. The influence of such parameters as the grading, crack length and crack period on the stress intensity factors is investigated.

The presence of notches or cracks causes stresses to amplify in nearby regions. This phenomenon is studied by estimating the Stress Concentration Factor (SCF) for notches, and the Stress Intensity Factor (SIF) for cracks. In the present work, a semi-analytical method under the framework of linear elasticity is developed to give an estimate of these factors, particularly for cracks and notches in finite domains. The solution technique consists of analytically deriving a characteristic equation based on the general solution and homogeneous boundary conditions, and then using the series form of the reduced solution involving the (possibly complex-valued) roots of this characteristic equation to satisfy the remaining non-homogeneous boundary conditions. This last step has to be carried out numerically using, say, a weighted residual method. In contrast to infinite domain problems where a fully analytical solution is often possible, the presence of more boundaries, and a variety in configurations, makes the solution of finite do-main problems much more challenging compared to infinite domain ones, and these challenges are addressed in this work. The method is demonstrated on several classical and new problems including the problems of a semi-circular edge notch in a semi-infinite and finite plate, an elliptical hole in a plate, an edge-crack in a finite plate etc.

The modified mapping-collocation (MMC) method is applied to analyze a circumferential crack in an isotropic curved beam. Based on the method a MATLAB code was developed to obtain the stress field. Incorporating the stress correlation technique, the opening and sliding fracture mode stress intensity factors (SIF)s of the crack for the beam under pure bending moment load case are calculated. The MMC method aims to solve two-dimensional problems of linear elastic fracture mechanics (LEFM) by combining the power of analytic tools of complex analysis (Muskhelishvili formulation, conformal mapping, and extension arguments) with simplicity of applying the boundary collocation method as a numerical solution approach. Qualitatively, a good agreement between the computed stress contours and the fringe shapes obtained from the photoelastic experiment on a plexiglass specimen is observed. Quantitatively, the results are compared with that of ANSYS finite element analysis software. The effect of crack size, crack position and beam thickness variation on SIF values and mode mixity is investigated.

Compression fracture specimens are ideally suited for miniaturization down to tens of microns. Fracture testing of thermal barrier coatings, ceramics and glasses are also best accomplished under compression or indentation. Compression fracture specimen of finite size with constant form factor was not available in the literature. The finite-sized specimen of edge cracked semicircular disk (ECSD) is designed which has the property of constant form factor. The novel ECSD specimen is explored further using weight function concept. This thesis, therefore, is mainly concerned with the design, development and geometric optimization of compression fracture specimen vis a vis their characterization of form factors, weight functions and isotropic points in the uncracked geometry. Inspired by the Brazilian disk geometry, a novel compression fracture specimen is designed in the form of a semicircular disk with an edge crack which opens up due to the bending moment caused by the compressive load applied along its straight edge. This new design evolved from a set of photoelastic experiments conducted on the Brazilian disk and its two extreme cases. Surprisingly, normalized mode-I stress intensity factor of the semicircular specimen loaded under a particular Hertzian way, is found constant for a wide range of relative crack lengths. This property of constant form factor leads to the development of weight function for ECSD for deeper analysis of the specimen. The weight function of a cracked geometry does not depend on loading configuration and it relates stress intensity factor to the stress distribution in the corresponding uncracked geometry through a weighted integral. The weight function for the disk specimen is synthesized in two different ways: using the conventional approach which requires crack opening displacement and the dual form factor method which is newly developed. Since stress distribution in the uncracked specimen is required in order to use weight function concept, analytical solution is attempted using linear elasticity theory. Since closed form solution for stresses in the uncracked semicircular disk is seldom possible with the available techniques, a new semi-analytical method called partial boundary collocation (PBC), is developed which may be used for solving any 2-D elasticity problem involving a semi-geometry. In the new method, part of the boundary conditions are identically satisfied and remaining conditions are satisfied at discrete boundary points. The classical stress concentration factor for a semi-in finite plate with a semicircular edge notch re-derived using PBC is found to be accurate to the eighth decimal. To enhance the form factor in order to test high-toughness materials, edge cracked semicircular ring (ECSR) specimen is designed in which bending moment at the crack-tip is increased significantly due to the ring geometry. ECSR is analyzed using nite element method and the corresponding uncracked problem is analyzed by PBC. Constant form factor is found possible for the ring specimen with tiny notch. In order to avoid varying semi-Hertzian angle during practice and thereby ensure consistent loading conditions, the designs are further modified by chopping at the loading zones and analyzed. Photoelastic isotropic points (IPs) which are a special case of zeroth order fringe (ZOF) are often found in uncracked and cracked specimens. An analytical technique based on Flamant solution is developed for solving any problem involving circular domain loaded at its boundary. Formation of IPs in a circular disk is studied. The coefficients of static friction between the surfaces of disk and loading fixtures, in photoelastic experiments of three-point and four-point loadings, are explored analytically to confirm with experimental results. The disk under multiple radial loads uniformly spaced on its periphery is found to give rise to one isolated IP at the center. Splitting of this IP into a number of IPs can be observed when the symmetry of normal loading is perturbed. Tangential loading is introduced along with normal loading to capture the effect of the composition on formation of IPs. Bernoulli's lemniscate is found to fit fringe order topology local to multiple IPs. Isotropic points along with other low fringe order zones including ZOF are ideal locations for material removal for weight reduction. Making a small hole in the prospective crack path at the IP location in the uncracked geometry might provide dual benefits: 1. Form factor enhancement; 2. Crack arrestor. Thus, this thesis describes experimental, theoretical and computational investigations for the design, development and calibration of novel compact compression fracture specimens.