Spelling suggestions: "subject:"etructural design -- data processing"" "subject:"etructural design -- mata processing""
1 |
ANALYSIS OF CYCLICALLY SYMMETRIC STRUCTURE UNDER NON-SYMMETRIC LOADING BY SUBSTRUCTURES.Kim, Sungmin. January 1984 (has links)
No description available.
|
2 |
Design procedures for self-supporting transmission towers.Hanna, Albert William Ghabbour. January 1971 (has links)
No description available.
|
3 |
The design of steel structures : a second-order approachMatson, Darryl Douglas January 1989 (has links)
The wide spread use of limit states design procedures in both the Canadian and American
steel design codes has created a need for a better understanding of how structures behave. Current design practice, however, allows and often encourages engineers to use an approximate linear analysis to determine the member forces in a structure. This is then followed by an even more approximate amplification of forces through the use of several design equations. It is believed that this practice is no longer acceptible as more accurate second-order computer programs have become a very practical alternative.
With this as motivation, this thesis will provide a comparison between a second-order computer program available at the University of British Columbia called ULA (Ultimate Load Analysis) and the Canadian and American building code designs, CAN3-S16.1-M84 and LRFD 1986 respectively.
It was felt that ULA should be verified, even though the theory it is based on is well established. Thus, ULA was used to generate a load versus L/r curve for a pin ended column (with the parameters modified slightly to allow direct comparison with the curves available in the codes). ULA was then used to predict load-deflection curves for two existing test frames. The resulting curves compared well with the test data.
To ensure simplicity, the building codes make several approximations in the derivation of their design equations. This results in the equations being applicable to a very narrow range of structures. Specifically, the equations apply to rigidly connected frames in which all of the columns reach their critical buckling load simmultaniously. Consequently, the results from ULA were compared to the codes for structures of this type. It was found that the codes were conservative for these structures in relation to the results from ULA,
yet the amount of conservatism varied greatly between structures. That is, the codes are not consistant in how conservative they are. Results from ULA were then compared to the codes for structures that do not satisfy all of the code limitations. Alhough using the codes to design structures beyond the limit of applicability is not a recommended practice, engineers do use the codes to design all types of structures, with little appreciation for the applicability limits. Consequently, it was deemed appropriate to extend this study to such structures. Though only a few were investigated, it was found that the codes were unreliable, being highly conservative, very accurate, or in one case highly unconservative when compared to the results from ULA. / Applied Science, Faculty of / Civil Engineering, Department of / Graduate
|
4 |
Design procedures for self-supporting transmission towers.Hanna, Albert William Ghabbour. January 1971 (has links)
No description available.
|
5 |
A theory of human error caussation in structural design: error predition & control via the soft system approachAdegoke, Israel Oludotun January 2016 (has links)
No description available.
|
6 |
Evaluation of a refined lattice dome modelHayes, Thomas S. January 1985 (has links)
A general review of lattice dome geometry and connection details, leads to a modeling approach, which introduces intermediate elements to represent connections. The method provides improved modeling of joint behavior and flexibility for comparative studies. The discussion of lattice domes is further specialized for parallel lamella geometry. A procedure is developed for minimizing the number of different member lengths. This procedure is incorporated into a program, which generates the geometric data for a specified dome.
The model is developed from a background which considers commercial space frame systems, static and dynamic loads, and modeling techniques using ABAQUS, a finite element program. An optional output of the generation program creates input data for ABAQUS. Modal analysis, static design loads, and earthquake loads are used in the evaluation of the model. / Master of Science
|
7 |
Efficient single-level solution of hierarchical problems in structural optimizationThareja, Rajiv R. January 1986 (has links)
Engineering design is hierarchical in nature, and if no attempt is made to benefit from this hierarchical nature, design optimization can be very expensive. There are two alternatives to taking advantage of the hierarchical nature of structural design problems. Multi-level optimization techniques incorporate the hierarchy at the formulation stage, and result in the coordinated optimization of a hierarchy of subsystems. The use of multi-level optimization techniques often necessitates the use of equality constraints. These constraints can sometimes cause numerical difficulties during optimization. Single-level decomposition techniques take advantage of the hierarchical nature to reduce the optimization cost.
In this research the decomposition approach has been followed to reduce the computational effort in a single-level design space. A decoupling technique has been developed that retains the advantages of a partitioned system of smaller independent subsystems without an increase in the total number of design variables. A penalty function formulation using Newton's method for the solution of a sequence of unconstrained minimizations was employed. The optimization of the decoupled system is cheaper due to (i) cheaper evaluation of the hessian matrix by taking advantage of its sparsity, (ii) fewer global analyses for constraint derivative calculations, and (iii) utilizing the decoupled nature of the hessian matrix in the solution process. Further, the memory requirements of the decoupled system are much less than that of the original coupled system. These benefits increase substantially for design problems with larger and larger number of detailed design variables.
Orthotropic material properties as stiffness global variables have been shown to be effective as global variables for panels in a hierarchical wing design formulation.
The proposed decoupling technique was implemented to minimize the volume of a portal frame and a wing box. Computational savings of up to 50 percent have been obtained for medium sized problems. The savings increase as the size of the problem and the amount of decoupling is increased. The procedure is simple to implement. For truly large systems this decoupling technique provides the necessary reduction of computational effort to make the optimization process viable. / Ph. D.
|
8 |
A study of full displacement design of frame structures using displacement sensitivity analysisAbou-Rayan, Ashraf M. 09 November 2012 (has links)
The intent of this study is to develop an algorithm for structural design based on allowable displacements for structural members, independent of stresses caused by the configurations imposed. Structural design can be based on displacement constraints applied in the same basic format as stress constraints so that convergence is based on allowable displacements rather than on stresses. / Master of Science
|
Page generated in 0.1184 seconds