In simulation of closely- or separately-joined rock masses, stability of rock blocks is of primary concern. However, there seems to be no approach that can handle general modes of simultaneous sliding and truly large rotation under general forces, including non-conservative forces such as water forces. General causes of failure for rock blocks, such as limit points, bifurcation points, and dynamic instability (divergence and flutter), have never been addressed. This research implements a formulation, called BS3D(an incremental-iterative algorithm introduced by Tonon), for analyzing general failure modes of rock blocks under conservative and non-conservative forces. Among the constitutive models for rock fractures developed over the years, Barton's empirical model has been widely used because it is easy to apply and includes several important factors associated with fracture characteristics. Although Barton's failure criterion predicts peak shear strength of rock fractures with acceptable precision, it has some weaknesses in estimating the peak shear displacement, post-peak shear strength, dilation, and surface degradation in unloading and reloading. In this dissertation, modifications are made to Barton's original model in order to address these weaknesses. The modified Barton’s model is validated by a series of direct shear tests on rock fractures and implemented in BS3D to consider the dilatant behavior of fractures. The mechanical behavior of a rock block formed in the roof of a tunnel is governed by its geometry, the mechanical characteristics and the deformability of the fractures forming the block, the deformability of the block and that of the surrounding rock mass, and the stresses within the rock. BS3D, after verification and validation, is used to investigate the effect of dilatancy on stability of rock blocks formed in the roof of a circular tunnel. High-velocity plunging jets, issuing from hydraulic artificial or natural structures, can result in scouring of the rock riverbed or the dam toe foundation. Assessment of the extent of scour is necessary to ensure the safety of the dam and to guarantee the stability of its abutments. BS3D is used to investigate effect of high-velocity jet impact on stability of rock blocks in plunge pools. / text

The Ph.D. thesis is focused on a surface degradation mechanisms under combined heat and mechanical load. The objects of examination are work rolls from hot rolling mill which suffer such a load. In first chapter, the hot rolling process, the design, the manufacturing process and present materials of work rolls are described. The state-of-the-art study of work roll surface degradation mechanisms – wear, oxidation, thermal and contact fatigue are described in the second chapter. The characterization, the formation, the mechanisms of progression and the effects of each surface degradation mechanism is described step by step. The state-of-the-art study of analytical and numerical models which are related to hot rolling process is described in third chapter together with their limitations and flaws. The next chapters contain design of an analytical, an optimized macroscopic and a microscopic model for study of the work roll stress state. The macroscopic and the microscopic model is based on finite element method and they are implemented in ANSYS Programming Design Language. The models are used to process several case study which are based on previous experimental work of the Heat transfer and fluid flow laboratory. The results from case studies specify and expand the knowledge of work roll stress state. The results show the portion of each loading factor on the whole stress state. In addition, time and depth depended distribution of stress state is presented. The results from macrosferic model illustrate the cause of spalling and a rupture of the work roll. The results from the microsferic model show the cause of creation of the to-surface-parallel cracks within carbides of high chromium irons. Last chapter summarized of all results gathered from case studies together with the goals for further research definition. The necessary steps for further cognition are stated. The thesis contains a large set of appendixes with deeper discussion of several related topics. These appendixes represent the one third of whole the thesis.

Surface modification techniques have played important roles in various aspects of modern technology. They have been employed to improve substrates by altering surface physicochemical properties. An ideal surface modifying technique would be a method that is applicable to any kind of materials prepared from a wide range of polymers and that can occur under mild reaction conditions. The work in this thesis has utilized four main concepts: I) the development of a ‘grafting-from’ technique by covalently growing polymer grafts from particle surfaces, II) the presence of steric and electrosteric forces due to long-range repulsive interactions between particles, III) a combined surface grafting and layer-by-layer approach to create polyelectrolyte multilayers (PEMs) on particle surfaces to fabricate strong and functional materials, and IV) the roles of hydrophilic polymer grafts and substrate geometry on surface degradation. A non-destructive surface grafting technique was developed and applied to polylactide (PLA) particle surfaces. Their successful modification was verified by observed changes to the surface chemistry, morphology and topography of the particles. To quantify the aggregation behavior of grafted and non-grafted particles, force interaction measurements were performed using colloidal probe atomic force microscopy (AFM). Long-range repulsive interactions were observed when symmetric systems, i.e., hydrophilic polymer grafts on two interacting surfaces, and asymmetric system were applied. Electrosteric forces were observed when the symmetric substrates interacted at pH 7.4. When PEMs were alternately assembled on the surface of poly(L-lactide) (PLLA) particles, the grafted surfaces played a dominated role in altering the surface chemistry and morphology of the particles. Three-dimensional scaffolds of surface grafted particle coated with PEMs demonstrated high mechanical performance that agreed well with the mechanical performance of cancellous bone. Nanomaterials were used to functionalize the scaffolds and further influence their physicochemical properties. For example, when magnetic nanoparticles were used to functionalize the scaffolds, a high electrical conductivity was imparted, which is important for bone tissue regeneration. Furthermore, the stability of the surface grafted particles was evaluated in phosphate buffered saline (PBS) solution. The nature of the hydrophilic polymer grafts and the geometry of the PLLA substrates played central roles in altering the surface properties of films and particles. After 10 days of PBS immersion, larger alterations in the surface morphology were observed on the film compared with microparticles grafted with poly(acrylic acid) (PAA). In contrast to the PAA-grafted substrates, the morphology of poly(acrylamide) (PAAm)-grafted substrates was not affected by PBS immersion. Additionally, PAAm-grafted microparticulate substrates encountered surface degradation more rapidly than PAAm-grafted film substrates. / <p>QC 20151002</p>