Depleting oil reserves and increased costs of the oil and gas recoveries have created the need to drill in challenging formations. When drilled through, shale formations in particular always generated a wide variety of problems if conventional water-based muds are used. Furthermore, the complexity and variations in shales have compounded the task of developing suitable drilling fluids. In light of these problems, the study of shale properties and their interactions with fluids will continue to be a muchneeded source of information in drilling industry. In this study a low molecular weight quaternary amine compound, which is provided by KarKim Drilling Fluids Inc., and its mixtures with sodium and potassium chloride is investigated in the aspects of capillary suction times, hot rolling recoveries, methylene blue capacities and one-dimensional free swelling properties in order to compare performances of salts and amine compound. For all test methods quaternary amine concentration from 1% to 6% by volume were studied and seen that less amount of quaternary amine compound is needed in order to obtain close shale recoveries and shale volume change potential if compared with sodium and potassium chloride. This prevents the usage of high concentration of chlorides and hence provides environmental sensitiveness. Furthermore, it was concluded that combining an amount of salt with quaternary amine compound gives the system enhanced shale inhibition properties.

Electrochemical biosensors are cost effective, fast and portable devices, which can determine the existence and amounts of chemicals in a specific medium. These devices have many potential applications in many fields such as determination of diseases, process and product control, environmental monitoring, and drug research. To realize these potentials of the devices, many studies are being carried out to increase their sensitivity, selectivity and long term stabilities. Surface modification studies with various types of particles (metal nano particles, carbon nano tubes etc.) can be count among these studies. Although zeolites and zeo-type materials are investigated for many years, they still hold interest on them due to their capabilities. By means of their chemical resistances, large surface areas, tailorable surface properties, and porous structures they can be applied in many applicational fields. In some recent studies, these properties are intended to be used in the field of biosensors. The purpose of the current study was to investigate the effect of zeolite nanoparticles on electrochemical biosensor performances. Firstly, several different procedures were investigated in order to find the best and optimum methodology to attach previously synthesized zeolites on Si wafer substrates for the first time. For this purpose, the ultrasonication, spin coating and direct attachment methods were used and their efficiencies were compared. Perfectly oriented, fully covering, zeolite monolayers are produced by direct attachment method. Successively produced zeolite thin films were then patterned with the help of Electron Beam Lithography technique to show the compatibility of coating methods to the CMOS technology. Combination of Direct Attachment and EBL techniques resulted well controlled zeolite monolayer patterns. Then zeolite modified electrochemical biosensors were tested for their performances. With these experiments it was intended to improve the selectivity, sensitivity and storage stabilities of standard electrochemical biosensors. Experiments, conducted with different types of zeolites, showed that zeolites have various effects on the performances of electrochemical biosensors. Amperometric biosensor response magnitudes have been doubled with the addition of Silicalites. Faster conductometric electrode responses were achieved with enzyme immobilization on zeolite film technique. Also it is seen that Beta type zeolites modified through different ion exchange procedures, resulted different responses in IS-FET measurements.

Depletion in the reserves of fossil fuels, inefficient energy production from these fuels and the negative effect of their usage on atmosphere, and thereby, on human health have accelerated researches on clean energy. Hydrogen produced from ethanol when used in fuel cells not only generates efficient energy but also creates a closed carbon cycle in nature. ZnO and Cu/ZnO catalysts are known with their superior performance in alcohol synthesis. From the principle of microkinetic reversibility they are expected to be superior catalysts for the steam reforming reaction of ethanol as well. ZnO catalysts can be modified by precious, Pd, or non-precious, Cu, metals to enhance hydrogen desorption capability, and dispersed on SiO2 for high surface areas via sol-gel technique. Steam reforming tests over ZnO catalysts revealed that they act only as ethanol dehydrogenation catalysts in the temperature range of 300-500C. Promotion with Pd or Cu decreased hydrogen selectivity due most probably to unreachable closed pores of the catalysts. Autothermal reforming tests over both ZnO/SiO2 and Co/SBA-15 catalysts, on the other hand, gave rise to the formation of several side products.

Industrial production of hydrogen from the syngas, generated from steam reformation of natural gas or coal gasification, sets conditions for hydrogen separation membranes in terms of operating conditions. An alternative source for hydrogen is a syngas generated by gasification of municipal solid wastes which are likely to set more stringent conditions for the separation membranes. There is therefore, a growing demand for separation membranes with improved permeability and particularly of low cost. Among various alternatives, metallic membranes are particularly attractive due to their high selectivity and permeability for hydrogen, exemplified by palladium (Pd). However, due to high cost of Pd there is still a demand to develop alternative metallic membranes that are of low cost and have improved durability. Efforts have therefore concentrated on either alloying Pd so as to reduce its cost or on alternative membrane compositions of particularly b.c.c. structure. The current study deals with hydrogen separation membranes and aims to develop infrastructure for rapid identification of membrane compositions with improved permeability. The study is made up of three parts / i) development of sputter deposition system that would allow deposition of multiple compositions in a single experiment, ii) development of substrate material that would support the thin film membranes and would allow permeability measurement and iii) development of a set-up to measure the permeability of the thin film membranes. In the present thesis, a sputter deposition system incorporating three targets was successfully constructed. The system as tested with palladium-niobium-titanium (Pd-Nb-Ti) ternary system after necessary adjustment would yield thin films of homogenous thickness (&le / 7%) over a sample area of &asymp / 150 mm diameter. A total of 21 substrates each in 19 mm diameter arranged in triangular form in the substrate holder could successfully be deposited where composition distributions covered a greater portion of Pd-Nb-Ti ternary phase diagram. The structure of the deposited thin films can successfully be controlled by substrate temperature as well as by the pressure of plasma gas (argon). With the help of these parameters, structural diversity can also be produced beside the compositional variation. As for substrates, two materials were investigated. These were titanium dioxide (TiO2) modified porous stainless steel (PSS) and anodic porous alumina (AAO). TiO2 modified PSS due to its associated surface roughness leads to the deposition of films with defected structure which as a result is not gas tight. AAO produced via anodization of aluminum foil had a regular (40-60 nm) pore structure that provides a suitable surface for thin film depositions which could be defect free. However, AAO is very delicate and fragile which makes it difficult to adapt it as a support material for permeability measurement/hydrogen separation purposes. Finally, a set-up was developed for measurement of hydrogen permeability which is capable of measurement over a wide pressure and temperature conditions, i.e. hydrogen pressures up to 10 bar and temperature as high as 450 &deg / C. It is recommended that so as to identify compositions with improved permeability, Nb or a similar metal which has extremely high permeability could be used as a support material. This would tolerate the evaluation of the films which are not totally defect free.

In this study, the aim is to investigate the stiffness, longitudinal tensile strength and circumferential tensile strength of short fiber reinforced polyester composite pipes produced by centrifugal casting production method. To achieve this aim, theoretical calculation of modulus of elasticity of pipes was done and then test program was carried out on pipe samples produced with three different resin types which were orthophthalic, isophthalic and vinyl ester resin and three different fiber types which were E glass fiber, ECR glass fiber and basalt fiber. The tests were performed according to ISO (International Organization for Standardization) standards. When resin type and fiber type effect on the fiber reinforced polyester pipe samples were evaluated, calculated elastic modulus values were in accordance with the test results. According to the experimental test data, which were used to evaluate the effect of resin type on fiber reinforced polyester pipe properties, there is not a significant difference was observed in the stiffness, longitudinal and circumferential tensile strength test results of pipes having different resin types. In other words, there was not a significant effect of resin type on the stiffness, longitudinal tensile strength and circumferential tensile strength of short fiber reinforced pipes produced by centrifugal casting method. According to the experimental test data, which were used to evaluate the effect of fiber type on the properties of fiber reinforced polyester pipe, basalt fiber reinforced pipe samples showed higher mechanical performance over E glass fiber and ECR glass fiber reinforced pipes. However, the test results of basalt reinforced polyester pipe were not as good as the individual properties of basalt fiber. Finally, by comparing the basalt fiber reinforced pipe samples having almost the same stiffness and tensile test results as E glass fiber reinforced pipe samples, the gain in fiber and resin amount were investigated. Basalt fiber reinforced pipes were slightly lighter and thinner than E glass fiber reinforced pipes. However, the decrease in the amount of the fiber and resin in basalt reinforced pipe did not result in an overall cost reduction.

Apatite was formed on the surface of titanium dioxide (TiO2) powders by a biomimetic process. The deposition was accomplished by immersing TiO2 powders in simulated body fluid (SBF) for 1, 3, 6, 12, and 24 h. SBF used throughout this study had calcium and phosphate ion concentrations 10 times greater than those of human blood plasma. Photocatalytic activity of the apatite-deposited TiO2 powders was investigated in terms of the decomposition of methylene blue solution under ultraviolet (UV) irradiation. It has been shown that apatite deposition enhanced the photocatalytic activity of TiO2. The best photocatalytic performance was acquired on the powders that are immersed in SBF for 3 h. The time required for the complete degradation of methylene blue decreased from 3.5 h to 2 h upon immersion of powders in SBF for 3 h. Photochemical durability of poly(methyl methacrylate) increased when it was mixed with apatite-deposited TiO2 powders.

Hydrogen and oxygen or air polymer electrolyte membrane fuel cell is one of the most promising electrical energy conversion devices for a sustainable future due to its high efficiency and zero emission. Membrane electrode assembly (MEA), in which electrochemical reactions occur, is stated to be the heart of the fuel cell. The aim of this study was to develop methods for preparation of MEA with alternative polymer electrolyte membranes and compare their performances with the conventional Nafion&reg / membrane. The alternative membranes were sulphonated polyether-etherketone (SPEEK), composite, blend with sulphonated polyethersulphone (SPES), and polybenzimidazole (PBI). Several powder type MEA preparation techniques were employed by using Nafion&reg / membrane. These were GDL Spraying, Membrane Spraying, and Decal methods. GDL Spraying and Decal were determined as the most efficient and proper MEA preparation methods. These methods were tried to improve further by changing catalyst loading, introducing pore forming agents, and treating membrane and GDL. The highest performance, which was 0.53 W/cm2, for Nafion&reg / membrane was obtained at 70 0C cell temperature. In comparison, it was about 0.68 W/cm2 for a commercial MEA at the same temperature. MEA prepared with SPEEK membrane resulted in lower performance. Moreover, it was found that SPEEK membrane was not suitable for high temperature operation. It was stable up to 80 0C under the cell operating conditions. However, with the blend of 10 wt% SPES to SPEEK, the operating temperature was raised up to 90 0C without any membrane deformation. The highest power outputs were 0.29 W/cm2 (at 70 0C) and 0.27 W/cm2 (at 80 0C) for SPEEK and SPEEK-PES blend membrane based MEAs. The highest temperature, which was 150 0C, was attained with PBI based MEA during fuel cell tests.