With the ongoing trend in moving the upper levels of the automation hierarchy to the cloud, there has been investigation into supplying industrial automation as a cloud based service. There are many practical considerations which pose limitations on the feasibility of the idea. This research investigates some of the requirements which would be needed to implement a platform which would facilitate competition between different controllers which would compete to control a process in real-time. This work considers only the issues relating to implementation of the philosophy from a control theoretic perspective, issues relating to hardware/communications infrastructure and cyber security are beyond the scope of this work. A platform is formulated and all the relevant control requirements of the system are discussed. It is found that in order for such a platform to determine the behaviour of a controller, it would need to simulate the controller on a model of the process over an extended period of time. This would require a measure of the disturbance to be available, or at least an estimate thereof. This therefore increases the complexity of the platform. The practicality of implementing such a platform is discussed in terms of system identification and model/controller maintenance. A model of the surge tank from SibanyeStillwater’s Platinum bulk tailings treatment (BTT) plant, the aim of which is to keep the density of the tank outflow constant while maintaining a steady tank level, was derived, linearised and an input-output controllability analysis performed on the model. Six controllers were developed for the process, including four conventional feedback controllers (decentralised PI, inverse, modified inverse and H¥) and two Model Predictive Controllers (MPC) (one linear and another nonlinear). It was shown that both the inverse based and H¥ controllers fail to control the tank level to set-point in the event of an unmeasured disturbance. The competing concept was successfully illustrated on this process with the linear MPC controller being the most often selected controller, and the overall performance of the plant substantially improved by having access to more advanced control techniques, which is facilitated by the proposed platform. A first appendix presents an investigation into a previously proposed switching philosophy [15] in terms of its ability to determine the best controller, as well as the stability of the switching scheme. It is found that this philosophy cannot provide an accurate measure of controller performance owing to the use of one step ahead predictions to analyse controller behaviour. Owing to this, the philosophy can select an unstable controller when there is a stable, well tuned controller competing to control the process. A second appendix shows that there are cases where overall system performance can be improved through the use of the proposed platform. In the presence of constraints on the rate of change of the inputs, a more aggressive controller is shown to be selected so long as the disturbance or reference changes do not cause the controller to violate these input constraints. This means that switching back to a less aggressive controller is necessary in the event that the controller attempts to violate these constraints. This is demonstrated on a simple first order plant as well as the surge tank process. Overall it is concluded that, while there are practical issues surrounding plant and system identification and model/controller maintenance, it would be possible to implement such a platform which would allow a given plant access to advanced process control solutions without the need for procuring the services of a large vendor. / Dissertation (MEng)--University of Pretoria, 2020. / Electrical, Electronic and Computer Engineering / MEng / Unrestricted

The thesis proposes heating the family log house. It contains a theoretical analysis of thermal insulation and thermal behavior of log house. The work on the proposed experiment termocentral box, who cares about the operation and management of the heating in the house with the possibility of control over the internet. The findings were practiced in the design of heating through termocentral box the heat source for wood, storage tank and preparation hot water.

In direct teleoperation the interface is vital to control a robot. Often it is reduced to a simple controller and the feedback provided by a camera stream in a monitor which leads to poor results. A telepresence system combined with a Free Look Control is proposed to increase the result in terms of situational awareness, usability and comfort. The telepresence system provides the sense of depth to the operatorin several manners. Free Look Control replaces Tank Control as control mode, in which the robot can be driven in any direction and the operator takes the control of the camera. A synergy is found when both features are implemented together as their advantages are increased. In addition a multi-camera setup is created, in order to build the 3D environment shown to the operator, which is calibrated in an automatic way. The two different control modes are tested and compared by several people. The outcome shows how the inclusion of these characteristics improve the result of the teleoperation in a visible way.