There exists considerable debate in the texture community about whether grain interactions are a necessary factor to explain the development of deformation textures in polycrystalline metals. Computer simulations indicate that grain interactions play a significant role, while experimental evidence shows that the material type and starting orientation are more important in the development of texture and microstructure. A balanced review of the literature on face-centered cubic metals shows that the opposing viewpoints have developed due to the lack of any complete experimental study which considers both the intrinsic (material type and starting orientation) and extrinsic (grain interaction) factors. In this study, a novel method was developed to assemble ideally orientated crystalline aggregates in 99.99\% aluminum (Al) or copper (Cu) to experimentally evaluate the effect of grain interactions on room temperature deformation texture. Ideal orientations relevant to face-centered cubic rolling textures, Cube $\{100\}\left<001\right>$, Goss $\{110\}\left<001\right>$, Brass $\{110\}\left<1\bar{1}2\right>$ and Copper $\{112\}\left<11\bar{1}\right>$ were paired in different combinations and deformed by plane strain compression to moderate strain levels of 1.0 to 1.5. Orientation dependent mechanical behavior was distinguishable from that of the neighbor-influenced behavior. In interacting crystals the constraint on the rolling direction shear strains ($\gamma_{_{XY}}, \gamma_{_{XZ}}$) was found to be most critical to show the effect of interactions via the evolution of local microstructure and microtexture. Interacting crystals with increasing deformations were observed to gradually rotate towards the S-component, $\{123\}\langle\bar{6}\bar{3}4\rangle$. Apart from the average lattice reorientations, the interacting crystals also developed strong long-range orientation gradients inside the bulk of the crystal, which were identified as accumulating misorientations across the deformation boundaries. Based on a statistical procedure using quaternions, the orientation and interaction related heterogeneous deformations were characterized by three principal component vectors and their respective eigenvalues for both the orientation and misorientation distributions. For the case of a medium stacking fault energy metal like Cu, the texture and microstructure development depends wholly on the starting orientations. Microstructural instabilities in Cu are explained through a local slip clustering process, and the possible role of grain interactions on such instabilities is proposed. In contrast, the texture and microstructure development in a high stacking fault energy metal like Al is found to be dependent on the grain interactions. In general, orientation, grain interaction and material type were found to be key factors in the development of rolling textures in face-centered cubic metals and alloys. Moreso, in the texture development not any single parameter can be held responsible, rather, the interdependency of each of the three parameters must be considered. In this frame-work polycrystalline grains can be classified into four types according to their stability and susceptibility during deformation. / Thesis (Ph.D, Mechanical and Materials Engineering) -- Queen's University, 2009-09-25 23:59:11.809

Les substrats métalliques ont été élaborés par des traitements thermomécaniques (laminages et recuits)sur des alliages Fe48%Ni et Ni5%W dans le but d'obtenir une hypertexture Cube indispensable à l'épitaxie de l'YBaCuO et du silicium dans la fabrication des câbles supraconducteurs et des cellules photovoltaïques à couches minces. Le rôle des éléments d'alliages tels que le soufre et le niobium sur la recristallisation et la formation de l'hypertexture Cube a été étudié dans le Fe48%Ni. Il a été montré que l'ajout du soufre favorise le développement de la texture Cube alors que l'ajout du niobium empêche la formation de la texture Cube. Le soufre se combine avec le Mn pour former les précipités MnS qui contribuent à l'augmentation de la différence d'énergie stockée entre l'orientation Cube et les orientations de laminage à froid (ECube/autres) quand le soufre augmente. Ce gap d'énergie explique explique l'acuité de la texture Cube avec l'ajout du soufre. Contrairement au soufre, l'ajout du niobium empêche la formation de la texture Cube, ce résultat s'explique par le fait la différence d'énergie stockée entre l'orientation Cube et les orientations de laminage diminue avec l'ajout du niobium. Pour expliques tous ces résultats, les analyses de microstructures et textures ont été faites par la technique EBSD et l'énergie stockée a été estimée à partir de la diffraction des neutrons sur les états déformés. / Substrate tapes were prepared by cold rolling and annealing of a Fe48%Ni and Ni5%W alloys in order to obtain Sharp Cube {100}<001> oriented substrate for photovoltaic thin films and superconductor cables in particular.The effect of microalloying elements sulfur and niobium on recrystallization and sharp Cube formation was studied in Fe48%Ni. It was shown that the addition of sulfur promotes the formation of Cube grains while the addition of niobium prevents the Cube grains formation. Regarding sulfur, it combines with manganese to form the MnS precipitates wich increases the stored energy difference between Cube component and others cold rolled components ECube/other when sulfur is added. This stored energy difference explains the sharpness of the Cube texture when sulfur is added. On the contrary the niobium microalloying element addition prevents the formation of Cube grains. This could be explained by the fact that stored energy of cold-rolled components decreases with the addition of niobium and thus decreases Cube grains fraction when niobium is added. In order to explain these results, the development of Cube texture during recrystallization has been investigated in detail by EBSD, furthermore, the effect of stored energy has been studied by carrying out neutron diffraction measurements on the deformed states.