In this thesis is dealed the technical term diagnostic with Fluke Ti55 thermo imager. In the introduction of description is analyzed noncontact temperature measurement including principle, uncertainties measurement and measurement system. In other parts of the work is focused on thermal imaging, termogram, description Fluke Ti55 termo imager and measurement of mechanical stress. The concluding part of the description and processing of measurements, including their evaluation.

In this thesis is dealed the technical term diagnostic with Fluke Ti55 thermo imager. In the introduction of description is analyzed noncontact temperature measurement including principle, uncertainties measurement and measurement system. In other parts of the work is focused on thermal imaging, termogram, description Fluke Ti55 termo imager and measurement of mechanical stress. The concluding part of the description and processing of measurements, including their evaluation.

Approved for public release, distribution is unlimited / In this study, the use of multi narrow-band filters was explored to correlate or fuse information to improve detection and recognition for specific targets of interest. To fully understand the viability and limitations of narrow band filters in thermal imaging, laboratory test procedures were first designed to characterize thermal images using common performance parameters, particularly the Noise Equivalent Temperature Difference (NETD), the Modulation Transfer Function (MTF) and the Minimum Resolvable Temperature (MRT). An available thermal imager, the Cincinnati Electronics IRRIS-256LN, and a newly purchased thermal imager, the Indigo Systems Merlin InSb Laboratory Camera, were investigated and compared. The MRT measurement showed a superior cut-off spatial frequency of 1.33 cycle/mrad for the Merlin camera, compared with 1.18 cycle/mrad for the Cincinnati, with similar sensitivity of about 0.1 ʻC for both cameras. Below cut-off the Modulation Transfer for the Merlin was approximately twice that of the Cincinnati. NETD measurements for both systems were inhibited by excess noise in the measurement system. The Merlin camera was consequently employed for further research on narrow band images. Three commercially available narrow band filters, 4110/4720 nm, 4540/4720 nm and 3750/4020 nm, were selected to isolate the "red" and "blue" spike signatures of plume emission and aerodynamic heating found in the signature of fast moving air targets. Similar sensor characterization was carried out with these filters, however, quantitative performance parameter measurements were hindered by excessive measurement system noise. As a preliminary study in multi-spectral image analysis, spectral features of hydrocarbon combustion were extracted from correlated narrow-band images of a laboratory propane flame. Digital analysis using software statistical tools showed potential for discrimination of hydrocarbon emission from other thermal sources by correlating pixel number and pixel radiant intensity. / Captain, Singapore Armed Forces

This paper deals with non-contact measurement of temperature in human faces. Principle of measurement of infrared radiation and construction of the thermal imager is described in a literature search. The main part of the paper is design of an algorithm for automatic processing and the detection of regions of interest in thermal images. The theoretical description of used methods is also included in this paper. The aim is to design and implement a program for automatic evaluation of temperature changes in a human face in a sequence of thermal images that were taken with short time delay. As a part of thesis is description of implementation of designed algorithm in programming enviroment MATLAB and the description of the user interface. The program was tested on the experimental data samples. Obtained results and possible limitations are also discused in this paper.

Diagnosis temperature is one of the most important disciplines. We meet it in everyday life, but it is very important for all sectors of industry. This is a measurement providing an immediate state of the measured object. Contact measurement of different temperature sensors and contactless measurement using thermal imagers. The important part is the measurement of temperature rise of induction motor. Part of the work deals with losses in the electric motor. These losses are converted into heat, which affects from various parts of the machine. Correct identification of the temperature field is important in helping to design the cooling system of the instrument. Virtually the data obtained are compared with theoretical data. We will capture part of the device and realize thermal simulations in a suitable simulation program. We propose modifying the cooling machine and the resulting data from the simulation compares.

This thesis is concerned with thermodiagnostics in industrial practise, which is very important for the assessment of technical condition of object on the basis of temperature, in today's time. It includes summary of contact and contact-free methods and their principle, advantages and disadvantages for aplication in industrial practise. Because of thesis it was carried out measurement in company Daikin Device Czech republic with the use of contact thermometer and two available thermocameras for solving of topical tasks relating to production.