Thesis (Ph. D.)--Virginia Polytechnic Institute and State University, 1992. / Vita. Abstract. Includes bibliographical references (leaves 230-242). Also available via the Internet.

Thesis (PhDElectronicEngineering)--University of South Australia, 2003.

No description available.

Thesis (Ph. D.)--University of Delaware, 2004. / Principal faculty advisor: S. Ismat Shah, Robert L. Opila, Dept. of Materials Science & Engineering. Includes bibliographical references (leaves 171-178).

This thesis presents the results of research into the potential of underground mining methods applicable to inclined thick seams (thickness greater than 3.5m, and seam dip of 15 - 35 degree) in the Quangninh coalfield, Vietnam. The primary objectives of this research are to investigate the most suitable underground methods applicable to inclined thick seams in the Quangninh coalfield and to improve understanding of the operational and geotechnical issues associated with the application of chosen methods in thick seams with steeply dipping conditions. From a risk and operational assessment, the Longwall Top Coal Caving (LTCC) method is considered most appropriate for inclined thick seams under the current mining conditions in Vietnam. The LTCC method offers great potential for the efficient extraction of thick seams by caving coal from the upper section during the mining of the lower section. This significantly reduces the development cost per tonne. Compared to High reach Single Pass Longwalling, the LTCC method offers a low extraction height, resulting in smaller and less expensive equipment and better face conditions. Results from this study identified that for extracting an inclined thick seam, the face retreating along the strike has better operational advantages and better cavability than the face retreating updip or downdip of the seam. The operational issues of the LTCC method when extracting inclined seams are: the stability of the support, transport in the mine, and the difficulties in roof control at the transition between face ends and the gateroads. In terms of geotechnical issues, better cavability of the top coal is anticipated for flat coal seams compared to inclined seams. In addition, the chain pillar for flat coal seams is subjected to a higher vertical stress distribution than that of inclined ones. An improved cavability assessment method for the categorisation of the cavability of the top coal with four categories, ranging from 1 (excellent cavability) to 4 (very poor cavability), was suggested to assist the feasibility and design stages of the LTCC application. The cavability assessment method was conducted by numerical analysis combined with back analysis from the database obtained from past LTCC practices.

This thesis presents the results of research into the potential of underground mining methods applicable to inclined thick seams (thickness greater than 3.5m, and seam dip of 15 - 35 degree) in the Quangninh coalfield, Vietnam. The primary objectives of this research are to investigate the most suitable underground methods applicable to inclined thick seams in the Quangninh coalfield and to improve understanding of the operational and geotechnical issues associated with the application of chosen methods in thick seams with steeply dipping conditions. From a risk and operational assessment, the Longwall Top Coal Caving (LTCC) method is considered most appropriate for inclined thick seams under the current mining conditions in Vietnam. The LTCC method offers great potential for the efficient extraction of thick seams by caving coal from the upper section during the mining of the lower section. This significantly reduces the development cost per tonne. Compared to High reach Single Pass Longwalling, the LTCC method offers a low extraction height, resulting in smaller and less expensive equipment and better face conditions. Results from this study identified that for extracting an inclined thick seam, the face retreating along the strike has better operational advantages and better cavability than the face retreating updip or downdip of the seam. The operational issues of the LTCC method when extracting inclined seams are: the stability of the support, transport in the mine, and the difficulties in roof control at the transition between face ends and the gateroads. In terms of geotechnical issues, better cavability of the top coal is anticipated for flat coal seams compared to inclined seams. In addition, the chain pillar for flat coal seams is subjected to a higher vertical stress distribution than that of inclined ones. An improved cavability assessment method for the categorisation of the cavability of the top coal with four categories, ranging from 1 (excellent cavability) to 4 (very poor cavability), was suggested to assist the feasibility and design stages of the LTCC application. The cavability assessment method was conducted by numerical analysis combined with back analysis from the database obtained from past LTCC practices.

Inductors and transformers constitute two important magnetic components In RF and power hybrids electronic circuitry. Thick film inductors have been subject of extensive research in recent years because they significantly reduce the weight and size, and increase the frequency of operation of electronic circuits. The research work in this dissertation is aimed at the formulation of thick film ferrite pastes and ferrite epoxies and the design, construction, and evaluation of thick film spiral inductors. Wideband characterization (DC - 2GHz) of ferrite pastes, ferrite epoxies, and ferrite substrates is performed using two techniques. These techniques are based on current image and transmission line (coaxial cavity) concepts for low (DC-IOOMHz) and high (50MHz-2GHz) frequency regions, respectively. They are used to evaluate the permeability spectra of formulated and commercially available thick film magnetic materials in respective frequency ranges. A method to numerically calculate the inductance of thick film circular spiral inductors based on modeling the spiral as concentric circles is presented. A novel method for fine as well as coarse tuning of thick film inductors is also introduced. The tunable inductors are constructed using formulated ferrite epoxies and magnetic cores. The method of analysis of variance is used to investigate the variation significance of tunable inductors. Finally, chemical and mechanical properties of developed magnetic materials are discussed. The studied properties include, glass transition temperature, degradation temperature, thermal coefficient of expansion, adhesion, particle-size distribution and particle densification , grain size, and compositional constituents of the magnetic materials. / Ph. D.

No description available.

Not available

No description available.