With rapid technology scaling, flip-flops are becoming more susceptible to metastability due to tighter timing budgets and the more prominent effects of process, temperature, and voltage variation that can result in frequent setup and hold time violations. This thesis presents a detailed methodology and analysis on the design of metastable-hardened, high-performance, and low-power flip-flops. The design of metastable-hardened flip-flops is focused on optimizing the value of τ mainly due to its exponential relationship with the metastability window δ and the mean-time-between-failure (MTBF). Through small-signal modeling, τ is determined to be a function of the load capacitance and the transconductance in the cross-coupled inverter pair for a given flip-flop architecture. In most cases, the reduction of τ comes at the expense of increased delay and power. Hence, two new design metrics, the metastability-delay-product (MDP) and the metastability-power-delay-product (MPDP), are proposed to analyze the tradeoffs between delay, power and τ. Post-layout simulation results have shown that the proposed optimum MPDP design can reduce the metastability window δ by at least an order of magnitude depending on the value of the settling time and the flip-flop architecture. In this work, we have proposed two new flip-flop designs: the pre-discharge flip-flop (PDFF) and the sense-amplifier-transmission-gate (SATG) based flip-flop. Both flip-flop architectures facilitate the usage in both single and dual-supply systems as reduced clock-swing flip-flop and level-converting flip-flop. With a cross-coupled inverter in the master-stage that increases the overall transconductance and a small load transistor associated with the critical node, the architecture of both the PDFF and the SATG is very attractive for the design of metastable-hardened, high-performance, and low-power flip-flops. The amount of overhead in delay, power, and area is all less than 10% under the optimum MPDP design scheme when compared to the traditional optimum PDP design. In designing for metastable-hardened and soft-error tolerant flip-flops, the main methodology is to improve the metastability performance in the master-stage while applying the soft-error tolerant cell in the slave-stage for protection against soft-error. The proposed flip-flops, PDFF-SE and SATG-SE, both utilize a cross-coupled inverter on the critical path in the master-stage and generate the required differential signals to facilitate the usage of the Quatro soft-error tolerant cell in the slave-stage.

With rapid technology scaling, flip-flops are becoming more susceptible to metastability due to tighter timing budgets and the more prominent effects of process, temperature, and voltage variation that can result in frequent setup and hold time violations. This thesis presents a detailed methodology and analysis on the design of metastable-hardened, high-performance, and low-power flip-flops. The design of metastable-hardened flip-flops is focused on optimizing the value of τ mainly due to its exponential relationship with the metastability window δ and the mean-time-between-failure (MTBF). Through small-signal modeling, τ is determined to be a function of the load capacitance and the transconductance in the cross-coupled inverter pair for a given flip-flop architecture. In most cases, the reduction of τ comes at the expense of increased delay and power. Hence, two new design metrics, the metastability-delay-product (MDP) and the metastability-power-delay-product (MPDP), are proposed to analyze the tradeoffs between delay, power and τ. Post-layout simulation results have shown that the proposed optimum MPDP design can reduce the metastability window δ by at least an order of magnitude depending on the value of the settling time and the flip-flop architecture. In this work, we have proposed two new flip-flop designs: the pre-discharge flip-flop (PDFF) and the sense-amplifier-transmission-gate (SATG) based flip-flop. Both flip-flop architectures facilitate the usage in both single and dual-supply systems as reduced clock-swing flip-flop and level-converting flip-flop. With a cross-coupled inverter in the master-stage that increases the overall transconductance and a small load transistor associated with the critical node, the architecture of both the PDFF and the SATG is very attractive for the design of metastable-hardened, high-performance, and low-power flip-flops. The amount of overhead in delay, power, and area is all less than 10% under the optimum MPDP design scheme when compared to the traditional optimum PDP design. In designing for metastable-hardened and soft-error tolerant flip-flops, the main methodology is to improve the metastability performance in the master-stage while applying the soft-error tolerant cell in the slave-stage for protection against soft-error. The proposed flip-flops, PDFF-SE and SATG-SE, both utilize a cross-coupled inverter on the critical path in the master-stage and generate the required differential signals to facilitate the usage of the Quatro soft-error tolerant cell in the slave-stage.

Des années 50 à nos jours, la propulsion électrique n'a cessé d'évoluer afin de s'imposer dans le domaine de la propulsion spatiale. Les Propulseurs à effet Hall (PEH) sont principalement utilisés pour des missions de correction de trajectoire ou de maintien en orbite des satellites. Ils délivrent des faisceaux d'ions à forte densité de courant et à faible énergie, ce qui en font de bons candidats potentiels pour d'autres applications comme la microélectronique ou encore les traitements de surfaces. Le xénon est l'ergol le plus utilisé en raison de sa masse élevée et de son faible énergie d'ionisation. Cependant son coût élevé et la difficulté d’approvisionnement motivent la recherche d'alternatives pour le fonctionnement des MEH. C'est dans ce cadre que cette thèse s'est inscrite avec l'idée d'un développement d'une source de faible puissance fonctionnelle en argon. L'amorçage d'une telle décharge n'étant pas immédiat, une démarche progressive qui passe par des décharges de mélange de gaz a été adoptée. Les décharges Xe-Ar se sont révélées très intéressantes pour la compréhension des mécanismes physiques qui régissent les PEH. La caractérisation en vitesse des ions Xe II (par Fluorescence Induite par Laser) associée à l'analyse en énergie par RPA a permis de remonter à des informations utiles sur les zones d'ionisation et d'accélération. Une technique originale de résolution temporelle du RPA basée sur une interruption rapide de la décharge ou sur les oscillations naturelles du courant de décharge, a été développée et a permis l'identification et la quantification des différentes espèces présentes dans le jet d'ions. Grâce aux résultats de l'étude paramétrique des décharges de mélange Xe-Ar, une décharge d'argon pur a pu être amorcée et caractérisée pour la première fois dans un PEH de faible puissance. / Since the 50s, electric propulsion has improved in order to establish itself on space propulsion field. The Hall Effect Thruster (HET) are mainly used for trajectory correction or satellites orbit maintaining. The HET provide high current densities and low energy ion beam that making it a good candidate for other applications such as microelectronics or surface treatments. Xenon propellant is most commonly used due to its high atomic mass and its low ionization energy. However, the high cost and difficult supply of xenon, leads to looking for alternative propellant for HET operation. In this context, this PhD thesis had as goal the development of a functional Argon low power source. Argon discharge ignition is not immediate, that why a progressive approach which involves gas mixture discharges was adopted. The Xe-Ar discharge gives very interesting results for the understanding of physical mechanisms governing HET. The characterization of Xe II ions velocity (Laser Induced Fluorescence) associated to the energy analysis by RPA have provided access to useful information on ionization and acceleration areas. An original time resolved RPA technique, based on an ultra-fast discharge interruption or on the discharge current oscillations, has been developed. This technique allows the identification and the quantification of different species present in the ion beam. Thanks to the discharge Xe-Ar study, a pure argon discharge could be initiated and characterized for the first time in a low power HET.