No description available.

Thesis (M.S.)--University of Alabama at Birmingham, 2008. / Title from PDF t.p. (viewed July 21, 2010). Includes bibliographical references.

Tissue engineering is an emerging area with an aim to create artificial tissues or organs by employing methods of biology, engineering and material science. In tissue engineering, scaffolds are three-dimensional (3D) structure made from biomaterials with highly interconnected pore networks or microstructure, and are used to provide the mechanical and biological cues to guide cell differentiation in order to form desired three-dimensional tissues or functional organs. Hence, tissue scaffold plays a critical role in tissue engineering. However, fabrication of such scaffolds has proven to be a challenge task. One important barrier is the inability to fabricate scaffolds with designed pore size and porosity to mimic the microstructure of native tissue. Another issue is the prediction of process-induced cell damage in the cell-involved scaffold fabrication processes. By addressing these key issues involved in the scaffold fabrication, this research work is aimed at developing methods and models to represent the dispensing-based solid free form scaffold fabrication process with and without the presence of living cells.<p> The microstructure of scaffolds, featured by the pore size and porosity, has shown to significantly affect the biological and mechanical properties of formed tissues. As such, during fabrication process the ability to predict and determine scaffold pore size and porosity is of great importance. In the first part of this research, the flow behaviours of the scaffold materials were investigated and a model of the flow rate of material dispensed during the scaffold fabrication was developed. On this basis, the pore size and porosity of the scaffolds fabricated were represented by developing a mathematical model. Scaffold fabrication experiments using colloidal gels with different hydroxylapatite volume fractions were carried out and the results obtained agreed with those from model simulations, indicating the effectiveness of the models developed. The availability of these models makes it possible to control the scaffold fabrication process rigorously, instead of relying upon a trial and error process as previously reported.<p> In the scaffold fabrication process with the presence of living cells, cells are continuously subjected to mechanical forces. If the forces exceed certain level and/or the forces are applied beyond certain time periods, cell damage may result. In the second part of this research, a method to quantify the cell damage in the bio-dispensing process is developed. This method consists of two steps: one step is to establish cell damage models or laws to relate cell damage to the hydrostatic pressure / shear stress that is applied on cells; and the second step is to represent the process-induced forces that cells experience during the bio-dispensing process and then apply the established cell damage law to model the percent cell damage in the process. Based on the developed method, the cell damage percents in the scaffold fabrication processes that employ two types of dispensing needles, i.e., tapered and cylindrical needles, respectively, were investigated and compared. Also, the difference in cell damage under the high and low shear stress conditions was investigated, and a method was developed to establish the cell damage law directly from the bio-dispensing process. To validate the aforementioned methods and models, experiments of fabricating scaffolds incorporating Schwann cells or 3T3 fibroblasts were carried out and the percent cell damage were measured and compared with the simulation results. The validated models allow one to determine of the influence of process parameters, such as the air pressure applied to the process and the needle geometry, on cell damage and then optimize these values to preserve cell viability and/or achieve the desired cell distribution within the scaffolds.

Tissue engineering is an emerging area with an aim to create artificial tissues or organs by employing methods of biology, engineering and material science. In tissue engineering, scaffolds are three-dimensional (3D) structure made from biomaterials with highly interconnected pore networks or microstructure, and are used to provide the mechanical and biological cues to guide cell differentiation in order to form desired three-dimensional tissues or functional organs. Hence, tissue scaffold plays a critical role in tissue engineering. However, fabrication of such scaffolds has proven to be a challenge task. One important barrier is the inability to fabricate scaffolds with designed pore size and porosity to mimic the microstructure of native tissue. Another issue is the prediction of process-induced cell damage in the cell-involved scaffold fabrication processes. By addressing these key issues involved in the scaffold fabrication, this research work is aimed at developing methods and models to represent the dispensing-based solid free form scaffold fabrication process with and without the presence of living cells.<p> The microstructure of scaffolds, featured by the pore size and porosity, has shown to significantly affect the biological and mechanical properties of formed tissues. As such, during fabrication process the ability to predict and determine scaffold pore size and porosity is of great importance. In the first part of this research, the flow behaviours of the scaffold materials were investigated and a model of the flow rate of material dispensed during the scaffold fabrication was developed. On this basis, the pore size and porosity of the scaffolds fabricated were represented by developing a mathematical model. Scaffold fabrication experiments using colloidal gels with different hydroxylapatite volume fractions were carried out and the results obtained agreed with those from model simulations, indicating the effectiveness of the models developed. The availability of these models makes it possible to control the scaffold fabrication process rigorously, instead of relying upon a trial and error process as previously reported.<p> In the scaffold fabrication process with the presence of living cells, cells are continuously subjected to mechanical forces. If the forces exceed certain level and/or the forces are applied beyond certain time periods, cell damage may result. In the second part of this research, a method to quantify the cell damage in the bio-dispensing process is developed. This method consists of two steps: one step is to establish cell damage models or laws to relate cell damage to the hydrostatic pressure / shear stress that is applied on cells; and the second step is to represent the process-induced forces that cells experience during the bio-dispensing process and then apply the established cell damage law to model the percent cell damage in the process. Based on the developed method, the cell damage percents in the scaffold fabrication processes that employ two types of dispensing needles, i.e., tapered and cylindrical needles, respectively, were investigated and compared. Also, the difference in cell damage under the high and low shear stress conditions was investigated, and a method was developed to establish the cell damage law directly from the bio-dispensing process. To validate the aforementioned methods and models, experiments of fabricating scaffolds incorporating Schwann cells or 3T3 fibroblasts were carried out and the percent cell damage were measured and compared with the simulation results. The validated models allow one to determine of the influence of process parameters, such as the air pressure applied to the process and the needle geometry, on cell damage and then optimize these values to preserve cell viability and/or achieve the desired cell distribution within the scaffolds.

Current treatments to intervertebral disc degeneration alter spine biomechanics and have complications. Tissue engineering offers an approach to regenerate a biological disc that provides flexibility and stability to, and integrates with the spine. To date, a scaffold that mimics the extracellular matrix composition and mechanical strength of a native disc is lacked. In this project, a biphasic scaffold was fabricated using glycosaminoglycan (GAG) and collagen, the prevalent ma-trix components in a native disc. It also adapted the structure of the disc, with la-mellae of collagen surrounding a collagen-GAG (CG) core. The first part of this project studied chemical modification of CG and evaluated the physiochemical and biological properties of modified CGs. As only loosely bound by GAG under physiological environment, collagen was modified by deamination, methylation and amination, and yielded Deaminated, Methylated and Aminated CGs upon co-precipitation with GAG. While GAG was mostly lost within 1 day in Untreated and Deaminated CGs, 20% and 40% GAG was retained after 6 days in Methylated and Aminated CGs respectively. In cell-seeded Aminated CG, over 60% GAG was retained after 8 days. Aminated CG, having the highest GAG/HYP of 4.5, best simulated the GAG-rich nucleus pulposus tissue. In ultrastructural analysis, Aminated CG consisted of abundant granular sub-stances that resembled the nucleus pulposus. Despite the differential initial number adhered to the CG scaffolds, human mesenchymal stem cells (hMSCs) had over 90% viability at all time points. Cell morphology was distinct, being round in Untreated and Methylated CGs but elongated in Deaminated and Aminated ones. The adhesion of hMSCs via collagen receptor, integrin alpha2beta1, was observed in all CG scaffolds, while adhesion via general matrix receptor, integrin alphaV, was extensive in all but Aminated CG. Based on improved GAG incor-poration and retention, which approximate the matrix composition of nucleus pulposus, Aminated CG was chosen as the core of the biphasic scaffold. The second part of this project studied lamination in biphasic disc scaffold and evaluated its mechanical properties in creep, recovery and dynamic loadings. A process was optimized to encapsulate a CG under physiological condition whilst producing an intact collagen gel, which allowed the CG to retain more GAGs and to be confined by the annulus structurally as was in the disc. This encasing approach was repeated for multiple lamellae, one lamella per day. Scaffolds with more lamellae had increased viscous compliance in creep and recovery, which was explained by the less laminated scaffolds being overloaded. Another lamination approach replaced most encasing lamellae with coiling ones. Despite low sample size, it was shown that this combined approach produced scaffolds with lower elastic and viscous compliances and longer equilibrating time in both creep and recovery, and higher complex modulus under dynamic loading. Full recovery was not achieved by any scaffold. This study demonstrated that a biphasic disc scaffold, made of GAG and collagen, contained similar matrix components to native disc, was almost mechanically comparable to the disc, and was cyto-compatible. It paved way towards tissue engineering of intervertebral disc and the intervertebral disc motion segment. / published_or_final_version / Mechanical Engineering / Doctoral / Doctor of Philosophy

Bone graft substitute is a continuously developing field in orthopedics. When compared to tradition biomaterial in the field such as PLA or PCL, elastomer like polyurethane offers advantages in its high elasticity and flexibility, which establish an intimate contact with surrounding bones. This tight contact can provide a stable bone-material interface for cell proliferation and ingrowth of bone. The aim of this study is to evaluate the osteogenesis capabilities of a porous polyurethane scaffold in a critical size bone defect. In this study, a porous scaffold synthesized from segmented polyurethane is put under in vitro and in vivo tests to evaluate its potential in acting as a bone graft substitute for critical size bone defects. In vitro results indicate osteoblast-like cells are proliferating on the polyurethane scaffold during the 21-days experiment. Cells express their normal morphology when seeded on polyurethane under fluorescent staining. Although cells show a relatively lower cell activity then that seeded on culture plate, they share a similar alkaline phosphatase activity profile with the controls during the experiment period. In the in vivo animal model, reconstructed images from micro CT scanning indicates there are bone ingrowth inside the scaffold. Histology also indicates a tight interface has formed between bone and polyurethane, with osteogenic cells proliferating on the surface. The result has indicates polyurethane is a potential material for orthopedics in acting as a bone graft substitute. / published_or_final_version / Orthopaedics and Traumatology / Master / Master of Philosophy

No description available.

No description available.

No description available.

Thesis (M.S.) --University of Texas Graduate School of Biomedical Sciences at San Antonio, 2008. / Vita. Includes bibliographical references.