Spelling suggestions: "subject:"itanium - tribology"" "subject:"itanium - ttribology""
1 |
Surface engineered titanium for improved tribological, electrochemical and tribo-electrochmical performanceBailey, Richard January 2015 (has links)
In the present study, efforts have been made to produce protective surface layers in order to improve the tribological, electrochemical and tribo-electrochemical response of titanium. In order to achieve this, two different techniques were employed: 1) thermal oxidation (TO) and 2) pack carburisation with oxygen diffusion (PC). Thermal oxidation of commercially pure titanium (CP-Ti) was undertaken at a temperature of 625 °C for durations of 5, 20 and 72 h. This results in a multi-layered structure comprising a titanium dioxide layer (rutile) atop of an α-titanium oxygen diffusion zone (α-Ti(O)). Initial attempts have also been made to improve the frictional behaviour of the oxide layer, using a prior surface mechanical attrition treatment (SMAT) and controlled slow cooling after oxidation. The results demonstrate that these prior and post treatments have a positive effect on the tribological performance of the oxide layer. Electrochemical and tribo-electrochemical characterisation was also carried out in a 0.9% NaCl solution. Electrochemical tests provided evidence that oxygen content in the upper part of the oxygen diffusion zone (depths < 5 μm from the surface) helps to accelerate passive film formation and thus improve the corrosion resistance of CP-Ti. Tribo-electrochemical testing of TO-Ti was carried out against an alumina counter face under various anodic and cathodic potentials. It is shown that the rutile oxide layer offers low friction and improved wear resistance. An unusual anodic protection behaviour for the oxide film has also been observed. When the TO-Ti is polarised anodically during sliding, the durability of the oxide layer is prolonged, resulting in low friction and much reduced material loss. In the present work a new pack carburising surface treatment method has been developed, whereby oxygen diffusion and carburisation of CP-Ti were undertaken concurrently. Optimisation of the process showed that a temperature of 925 °C for 20 h resulted in a multilayer structure comprising of a titanium carbide (TiC) network layer atop of a relatively thick α-Ti(O) diffusion zone. Tribological testing demonstrated that the new surface treatment can significantly enhance the tribological properties of titanium, in terms of much reduced friction (μ ≈ 0.2), improved wear resistance and enhanced load bearing capacity. Electrochemical corrosion testing also showed the PC-Ti retained the favourable corrosion characteristics of CP-Ti. Tribocorrosive testing revealed an improved tribological response when compared with that of untreated CP-Ti.
|
2 |
Fundamental Studies On Tribological Response Of Titanium And CopperNagaraj, C M 04 1900 (has links)
Friction and wear have been observed m mechanical systems when there is a relative motion between two solid bodies Friction mainly results in loss of energy and wear results in matenal loss The proper understanding of friction and wear mechanisms provides practical solutions to tribological related problems Various models are available m tribology literature to calculate function coefficient and wear rate of matenals However, expenments suggest that these models are incomplete and fortuitous as the tnbological response is system dependent
The objective of present investigation is to understand the tribological lesponse of commercially puie titanium and OFHC copper pins sliding on polyciystallme alumina discs Di\ shdm% tests were conducted in air, and vacuum (1 5 x 10~2Pa) at room tempeiatuie under different experimental conditions The normal load was vaned from 15 3 N to 76 0 N, sliding speed was vaned from 0 01 ms"1 to 1 4 ms"1, and tempeiatuie was varied from 293 K to 793 K It is found that the haidness of metals do not have any effect on their tribological response The experimental obseivations indicate that tribological response of metals mainly depends up on miciostructural evolution, oxygen activity and relative shear strength of metals and ceramics
Chapter 1 starts with the background and concepts of tribology A brief literature survey is given with published work in relation with the present work In Chapter 2, the experimental proceduies of the dry sliding test and compression test are given
Chapter 3 explains the tribological response of titanium during shdmg against alumina Different wear mechanisms such as oxidation, deformation and adhesion were identified Deformation wear mechanism is explained using strain rate response approach Chapter 4 explains the tribological response of copper during sliding against alumina The influence of environment and microstructural evolution on its tribological behavior are studied Chaptei 5 explains the dependence of tribological response of metals on micro structural evolution, oxygen activity and relative shear strength of metals and ceramics This thesis ends with the conclusions of the present investigation
|
Page generated in 0.072 seconds