The purpose of the thesis is to analyze the properties of acoustic sound field in the Sizihwan Bay Marine Test Field (SBMTF), and to conduct geoacoustic inversion using the measured data. Two experiments were carried out during February, 2009, and March, 2010. The source was UW350, and the receivers were ITC 6050 hydrophones. The transmitted frequencies lie between 350 Hz and 1250 Hz. On the analysis of acoustic propagation, the study calls for the application of OASES for the analysis of transmission loss and effects of range dependency. Moreover, the uncertainty analysis due to environmental factors was carried out based upon probabilistic approach. For the inversion analysis, the sensitivity of each environmental parameter was first analyzed, and those parameters with high sensitivity were chosen for inversion. Inversion was conducted by the application of SAGA. The results have shown that, due to the fact that the SBMTF is an very shallow water environment with water depth less than 30 m, the acoustic sound field is strongly affected by the boundaries. From the uncertainty analysis, it shows that the transmission loss has high degree of uncertainty resulting from seabed property due to its lack of accurate measurement. The inversion results for water depth and seabed sound speed were obtained, and compared with the measured data. This research calls for experimental design, data processing, software application, and result analysis, offering an overall understanding of the properties of SBMTF that is valuable for future study.

The sound transmission loss of a range of plywood panels was measured to investigate the influence of the orthotropic stiffness of the plywood panels. The plywood panels were tested as single and also double leaf partitions, with a range of stud configurations. A new method was developed for predicting the sound transmission loss of single leaf partitions with both orthotropic and frequency dependent stiffness values. The sound transmission loss was evaluated for two significantly different sample sizes. The observed influence of the sample size on the measured sound transmission loss was profound. The construction of the partition was shown to significantly affect the influence of the sample size on the sound transmission loss. A qualitative analysis based on existing published research of the contributing factors is presented, and methods for adjusting the results for the small sample size for comparison with the large results were developed. The influence of a range of acoustic treatments of lightweight plywood partitions was investigated. The treatments involved internal viscoelastic materials and decoupled mass loaded barriers in various arrangements. The attachment between the treatment and the plywood panel was found to influence the sound transmission loss significantly. A prediction method based on published models was modified to allow the influence of the treatments to be included. Reasonable agreement was achieved between the predicted and measured results for a wide range of samples. A prediction method was developed that accounts for the influence of orthotropic, frequency dependent material parameters. This method utilised an adaptive, numerical integration method to solve an analytical formulation for the sound transmission loss. The influence of the finite sample size was accounted for using an expression for the finite panel radiation impedance. The finite panel radiation impedance was predicted analytically and an approximation was also presented. The presence of a significant source room niche was accounted for by applying an appropriate limit to the integration range of the angle of incidence. The prediction methods developed are compared with the measured transmission loss results from both the small and large test facilities. Good agreement was seen for some of the predicted results. Generally the agreement within the coincidence region was worse than for the rest of the transmission loss curve. The inclusion of orthotropic and frequency dependent stiffness values significantly improved the agreement within the coincidence region.

No description available.

Noise in a fluid system can be treated with a prototypical liner-style suppressor, an expansion chamber which includes an internal annulus of syntactic foam. A syntactic foam liner consists of host material with hollow microspheres which collapse under pressure to add compliance to the suppressor. The liner effectively increases the transmission loss of the suppressor, or ratio between inlet and outlet acoustic energy. Currently, liner-style suppressors are not commercially available. This study investigates the integration of solid liner material within suppressor shells while also analyzing the effect of flow-smoothing diffusors on the transmission loss of the suppressor. The diffusors function to center the liner within the device, while reducing the potential for turbulence-induced self-noise. The diffusor may also impact the longevity of the liner, by reducing mechanical erosion. The results of the study provide additional insight to the commercial viability of the liner-style suppressor.

L'objectif de cette thèse consiste en l'étude d'une stratégie de contrôle actif à faible autorité avec comme application le contrôle actif du rayonnement acoustique d'une plaque. Depuis l'essor du contrôle actif, son application aux problèmes acoustiques et vibracoustiques a été investiguée par de nombreux chercheurs, exploitant soit la théorie du contrôle optimal, soit des approches originales basées plus particulièrement sur la physique. Des notions spécifiques au contrôle vibroacoustique ont été développées comme, par exemple, les modes radiatifs pouvant caractériser le rayonnement acoustique d'une plaque d'une manière adaptée au contrôle. Le contrôle actif à faible autorité, pour lequel le Laboratoire de Structures Actives a développé une expertise dans le domaine de l'amortissement et du contrôle actif des vibrations, est une solution attractive par sa simplicité de mise en oeuvre. Le plus souvent implémenté sous la forme d'un contrôle décentralisé constitué de boucles indépendantes, le contrôle à faible autorité bénéficie de certaines garanties de stabilité et de robustesse. Bien que notre stratégie de contrôle puisse s'appliquer à n'importe quel type de plaque, l'application considérée dans ce travail a été motivée par le contexte socio-économique actuel en rapport avec les nuisances acoustiques. Il était en effet intéressant d'évaluer la stratégie de contrôle pour le problème de la transmission acoustique d'un vitrage. La stratégie de contrôle se divise en deux étapes. Tout d'abord le développement d'un capteur unique destiné à fournir une mesure représentative du bruit rayonné par une plaque en basse fréquence. Deux capteurs de vitesse volumétrique (l'un discret, l'autre distribué) ont ainsi été développés et évalués expérimentalement. Ensuite, une procédure d'optimisation de l'emplacement d'un ensemble d'actionneurs pilotés en parallèle est proposée. L'objectif de cette phase d'optimisation est de forcer la réponse fréquentielle du système à posséder les propriétés d'un système colocalisé. La stratégie de contrôle est ensuite évaluée sur deux structures expérimentales. / This thesis is concerned with a low authority active control strategy applied to the sound radiation control of a baffled plate. Since the development of active control , numerous researchers have studied its application to acoustical or vibroacoustical problems using either the modern control theory or other methods based rather on the understanding of the physics of the problem. Vibroacoustical active control has lead to the definition of radiation modes allowing to describe the radiated sound of a plate in an appropriate manner for active control purposes. Low autorithy control (LAC), for which the Active Structures Laboratory has gained an expertise for active vibration control applications is an interesting solution for its implementation simplicity. Most of the time it consists of several decentralized control loops, and benefits from guaranteed stability and robustness properties. Although our control strategy can be applied to any kind of plates, the application considered here has been motivated by the present socio-economical context related to noise annoyances. The active control strategy has been applied the problem of the sound transmission loss of glass plates (windows). This strategy is in two steps : first a volume velocity sensor is developed as to give a measure representative of the radiated sound at low frequencies. Two sensors have been developed (one discrete and one distributed) and experimentally tested. Next, an optimisation strategy is proposed which allow to locate on the plate a set of several actuators driven in parallel. The goal of this optimisation task is to obtain an open-loop frequency response which behave like a collocated system. The control strategy is finally evaluated on two plate structures.

The sound transmission loss characteristics of plywood based sandwich panels were investigated. Measurements were made of the sound transmission loss of a range of materials and used as a baseline for comparison while a sound transmission loss optimisation method was developed. A unique test rig was built and calibrated to determine selected mechanical properties of materials of interest. The results of sound transmission loss and material properties measurements were used to select an appropriate prediction model, which was then used in conjunction with a mathematical optimisation model to determine combinations of materials and panel parameters which result in improved sound transmission loss. An effort was made to reproduce these predictions in experimental testing by constructing several prototype panels.

The Riverside Energy Efficiency Laboratory at Texas A&M University conducts sound quality testing for the Home Ventilating Institute. When the Home Ventilating Institute initially established their sound quality test, the semi-reverberant sound chamber to conduct the sound quality tests was built at the Riverside Energy Efficiency Laboratory. The Home Ventilating Institute created a standard to specify the procedure for sound quality testing. This standard contained high consideration for performance, reliability, and accuracy. The standard was based on several ANSI standards for sound testing procedures, sound setup and equipment standards, and sound rating calculations. The Riverside Energy Efficiency Laboratory presently continues sound quality testing for the Home Ventilating Institute using the semi-reverberant sound chamber. The standard has been revised and updated due to developments for better sound quality test result representation. Resourceful data to assist with further developments comes from the semi-reverberant sound chamber's characteristics. This thesis's purpose was to conduct an analysis of the performance for the semi-reverberant sound chamber. The sound chamber's sound transmission loss was determined using a fan source with known sound power across the 24 tested 1/3 octave frequency bands, 50 Hz - 10,000 Hz. The sound pressure was recorded inside the chamber and outside the chamber at the sound source. The sound source was placed at three different locations around the sound chamber. In addition, the sound pressure was measured in real time to study the amount of sound pressure fluctuation and maximum amplitude. The background noise was measured inside the sound chamber for these tests. The sound transmission loss profiles were identical for each location. The lowest two 1/3 octave bands, 50 Hz and 63 Hz, have low transmission losses. The profile jumps up at the following 1/3 octave band and increases with a peak around 1600 Hz before slightly decreasing. The profile of the sound pressure in the time domain showed similar results. The most fluctuation with the greatest peaks was present in the lower 1/3 octave frequency bands, and diminished the higher the 1/3 octave frequency band. Sound sources around the sound chamber can be evaluated to determine whether an impact is possible on the sound quality tests from these results. The impact of modifications to the sound chamber can use the transmission loss values to help determine the expected performance increase.

The distance of sound propagation in water is inversely proportional to the frequency; there for the low frequency noise generated by distance shipping contribute most to the low frequency components of the ocean ambient noise. In order to improve the performance of sonar application, understanding and predication shipping noise is important. In this study, noise data was collected by vertical line array (VLA), in South China Sea of Asian Seas International Acoustics Experiment (ASIEX) in 2001. Due to the limited access to the satellite imagery, and based on the assumption that fishing vessels in South China Sea has similar operational pattern and lighting in recent years, the night time satellite image data was acquired by Defense Meteorological Satellite Program DMSP - Operational Linescan System(DMSP-OLS) of 2005. Linear regression was analyzed between fishing light pixel distribution and low frequency noise level variation, fishing light was expressed in terms of total pixel number and total light intensity, and distance from fishing vessel to VLA was assumed by spherical and cylindrical spread. The results show high correlation between total light intensity and noise level, and cylindrical spreading is better assumption in shallow water on the continental shelf at low frequency. As a conclusion, this study successfully prove that by using the night satellite image, the low frequency fishing vessel noise can be predicted with reasonable accuracy.

No description available.

Lightweight building materials are now commonly employed in many countries in preference to heavyweight materials. This has lead to extensive research into the sound transmission loss of double leaf wall systems. These studies have shown that the wall cavity and sound absorption material placed within the cavity play a crucial role in the sound transmission through these systems. However, the influence of the wall cavity on the sound transmission loss is not fully understood. The purpose of this research is to obtain a comprehensive understanding of the role played by the wall cavity and any associated sound absorption material on the sound transmission loss through double leaf wall systems. The research was justified by the fact that some of the existing prediction models do not agree with some observed experimental trends. Gösele’s theory is expanded and used in the creation of an infinite and finite vibrating strip model in order to acquire the desired understanding. The sound transmission loss, radiated sound pressure and directivity of double leaf systems composed of gypsum boards and glass have been calculated using the developed model. A method for calculating the forced radiation efficiency has also been proposed. Predictions are compared to well established theories and to reported experimental results. This work also provides a physical explanation for the under-prediction of the sound transmission loss in London’s model; explains why Sharp’s model corresponds to Davy’s with a limiting angle of 61° and gives an explanation for Rindel’s directivity and sound transmission loss measurements through double glazed windows. The investigation also revealed that a wide variety of conclusions were obtained by different researchers concerning the role of the cavity and the properties of any associated sound absorption material on the sound transmission loss through double wall systems. Consequently recommendations about the ways in which sound transmission through cavity systems can be improved should always be qualified with regard to the specific frequency range of interest, type of sound absorption material, wall panel and stud characteristics.