Ma thèse en automatique s’inscrit dans la thématique de recherche «Transport» du LAMIH. L’objectif est d’améliorer le fonctionnement des moteurs thermiques (essence), notamment en réduisant la consommation et la pollution. Face à cet enjeu écologique et économique, et compte tenu des nouvelles normes et des stratégies court-termistes de l’industrie (scandale Volkswagen...), de nouveaux contrôleurs doivent être conçus pour piloter l’arrivée d’air et d’essence au sein du moteur. En considérant l’aspect hautement non-linéaire du système, la représentation Takagi-Sugeno et le background théorique du LAMIH sont utilisés. Un premier contrôleur est synthétisé pour régler le problème de la vitesse de ralenti du moteur. Cependant, la complexité du système impose l’utilisation d’un contrôleur très coûteux d’un point de vue computationnel. Un contrôleur alternatif est donc synthétisé afin d’être implémenté dans l’ordinateur embarqué du moteur. Un second contrôleur est obtenu pour maintenir la richesse en proportions stoechiométriques afin de réduire la pollution. Ce système étant sujet à un retard de transport variable, un changement de domaine est réalisé afin de rendre ce retard constant, et de concevoir un contrôleur simple et efficace. Des essais réels sur le banc d’essai moteur du LAMIH sont réalisés afin de valider la méthodologie présentée. / My PhD in Automatic Control is part of the research theme “Transport” of the LAMIH. The objective is to improve the functioning of the gasoline engines, mainly by reducing the fuel consumption and the pollution. With this ecologic and economic challenge, and taking into account the new norms and the short-term strategies of the industry (scandal of Volkswagen...), new controllers have to be designed to control the air valve and the fuel injection inside the engine. Considering the highly nonlinear aspect of the system, the Takagi-Sugeno representation and the theoretical background of the LAMIH have been used. A first controller is designed to solve the problem of idle engine speed. However, the complexity of the system forces the use of a controller that is very costly from a computational point of view. An alternative controller is then designed in order to be implemented inside the embedded computer of the engine. A second controller is obtained to maintain the air-fuel ratio in stoichiometric proportions in order to reduce the pollution. This system being subject to a variable transport delay, a change of domain is realized to make this delay constant, and to design a simple and efficient controller. Real-time experiments have been realized on the engine test bench of the LAMIH in order to validate the presented methodology.

This master thesis aims to develop a test methodology for electromechanical linear actuators. A linear actuator acts as a linear motor, converting a power source to linear motion. The electromechanical linear actuator in this project has an electric motor as its power source and uses a rack and pinion system to transfer that power to linear motion.  The test methodology is to impose a force onto the rack of the actuator, to ensure that operation under a load scenario is within specification. To accomplish this, the design of a test rig implementation is analyzed. The test rig consists of the test unit, which is to be tested, the load unit, which is to provide the load force, and a control system for the load unit. The load unit is another linear actuator and is controlled via a load cell. The load cell gives out the load force being applied, and the controller gives out the corresponding appropriate motor command to the load unit to ensure the load force is as desired. This analysis is done through simulation of the setup. Viable options for the setup were first analyzed in order to implement the deemed promising options for a setup into a simulation environment. The simulation environment in this project was Simscape, an extension of MATLAB’s Simulink. In simulation the parameters for the test rig were rigorously analyzed, in order to determine acceptable thresholds. The primary load unit tested was another electromechanical linear actuator from Cascade Drives, the model A-100-8P. Two secondary setups, one using the same model as being tested, and another setup using two of the models being tested. Simulation found that the suggested options’ applied load force have a poor rise time, large overshoot and substantial oscillation errors. The primary source for this was determined to be the latency between load cell input, and motor command output in the controller. The poor metrics from the result could lead to problems when emergency braking, and with a long honing period, which would render most test data unusable.

This thesis focuses on the methodology of controlling dynamic systems in real time. It contents a review of the control theory basis and the elementary base of regulators construction. Then the list of matemathic formulaes follows as well as the math basis for the system simulations using a difeerential count and the problem of difeerential equations solving. Furthermore, there is a systematic approach to the design of general regulator enclosed, using modern simulation techniques. After the results confirmation in the Matlab system, the problematics of transport delay & quantization modelling follow.