No

Thesis (MSc)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: Concrete filled double skin tube (CFDST) columns is a new method of column construction. CFDST columns consists of two steel hollow sections, one inside the other, concentrically aligned. The cross-sections of the two hollow sections does not have to be the same shape. Concrete is cast in between the two hollow sections resulting in a CFDST. This study only considers CFDST columns constructed with circular steel hollow sections. The advantages of CFDST construction include: ● The inner and outer steel hollow sections replaces the traditional steel reinforcement that would be used in a normal reinforced concrete column. This reduces the construction time since there is no need to construct a reinforcing cage. ● The steel hollow sections acts as a stay in place formwork, eliminating the need for traditional formwork. This also reduces construction time. ● The steel hollow sections confine the concrete, making it more ductile and increasing its yield strength. The objective of this study is to identify methods that can predict the axial capacity of eccentrically loaded circular CFDST columns. Methods chosen for the investigation are: 1. Finite element model (FEM). A model was developed to predict the behaviour of eccentrically loaded CFDST columns. The FE model uses a concrete material model proposed in literature for stub columns. The aim was to determine whether the material model is suited for this application. 2. The failure load of CFDST columns under concentric loading was calculated using a model obtained in literature. These capacities were compared to the experimental test results of eccentrically loaded CFDST columns to establish a correlation. This study found that the concrete material model used does not adequately capture the behaviour resulting in the axial response of the column being too stiff. The difference between the eccentrically loaded experimental test results and the calculated concentrically loaded capacity showed a clear trend that could be used to predict the capacity of eccentrically loaded CFDST columns. / AFRIKAANSE OPSOMMING: Beton-gevulde dubbel laag pyp (BGDLP) kolomme is ‘n nuwe metode van kolom konstruksie. BGDLP kolomme bestaan uit twee staal pyp snitte, die een binne die ander geplaas met hul middelpunte opgelyn, die dwarssnit van die twee pype hoef nie dieselfde vorm te wees nie. Beton word dan in die wand tussen die twee pyp snitte gegiet. Die resultaat is ‘n hol beton snit. Hierdie studie handel slegs oor BGDLP kolomme wat met ronde pyp snitte verwaardig is. Die volgende voordele kan aan BGDLP toegeken word: ● Die binne en buite staalpype vervang die tradisionele staal bewapening was in normale bewapende-beton gebruik sou word. Dus verminder dit die tyd wat dit sal neem om die kolom op te rig. ● Die staalpypsnitte is ook permanente vormwerk. Dit doen dus weg met die gebruik van normale bekisting, wat ook konstruksie tyd spaar. ● Die buite-staalpypsnit bekamp die uitsetting van die beton onder las. Hierdie bekamping veroorsaak dat die beton se gedrag meer daktiel is en ‘n hoër falings spanning kan bereik. Die doel van die studie is om metodes te identifiseer wat gebruik kan word om die aksiale kapasiteit onder eksentriese laste van BGDLP kolomme te bepaal. Twee metodes was gekies: 1. Eindige element model. ‘n Model was ontwikkel om die gedrag van BGDLP kolomme te voorspel. Die mikpunt was om te bepaal of ‘n beton materiaal gedrag model vanuit die literatuur gebruik kan word om BGDLP kolomme te modelleer. 2. Die swiglas van BGDLP kolomme onder konsentriese belasting was bereken vanaf vergelykings uit die literatuur. Hierdie swiglaste was vergelyk met die eksperimentele toets resultate vir eksentriese belaste BGDLP kolomme om ‘n korrelasie te vind. Hierdie studie het bewys dat die beton materiaal model uit die literatuur kan nie gebruik word om die swiglaste van BGDLP kolomme te bepaal nie. Die model het die gedrag te styf gemodelleer. Die verskil tussen die berekende konsentriese belaste swiglas en die eksperimentele resultate van eksentriese BGDLP kolomme was voorspelbaar en kan gebruik word om die swiglas van eksentriese belaste BGDLP kolomme te voorspel.

Composite concrete filled steel tube columns are increasingly used for high-rise building structures, owing to their excellent structural performance such as superior load-bearing capacity, high ductility, good energy dissipation and fire behaviour which arises from the combination of the two different materials in the structure. Composite structures exploit the characteristics of steel and concrete; steel with its high tensile strength and ductility and concrete with its high compressive strength and stiffness. In general, concrete filled composite columns with circular hollow sections (CHS) have the advantage over columns with other section shapes due to the circular cross sections providing a uniform confinement to the concrete core.

This paper summarises the data from 1819 tests on concrete-filled steel tube columns and compares their failure load with the prediction of Eurocode 4. The full data is given on the website http://web.ukonline.co.uk/asccs2 . The comparison with Eurocode 4 is discussed and shows that Eurocode 4 can be used with confidence and generally gives good agreement with test results, the average Test/EC4 ratio for all tests being 1.11. The Eurocode 4 limitations on concrete strength could be safely extended to concrete with a cylinder strength of 75 N/mm2 for circular sections and 60 N/mm2 for rectangular sections.

No / This paper presents the behaviour and design of axially loaded concrete filled stainless steel circular and square hollow sections. The experimental investigation was Conducted using different concrete cube strengths varied from 30 to 100 MPa. The column strengths and load-axial shortening curves were evaluated. The study is limited to cross-section capacity and has not been validated at member level. Comparisons of the tests results together with other available results from the literature have been made with existing design methods for composite carbon steel sections-Eurocode 4 and ACI. It was found that existing design guidance for carbon steel may generally be safely applied to concrete filled stainless steel tubes. though it tends to be over-conservative. A continuous strength method is proposed and it is found to provide the most accurate and consistent prediction of the axial capacity of the composite concrete filled stainless steel hollow sections due largely to the more precise assessment of the contribution of the stainless steel tube to the composite resistance.

During an earthquake, columns in a one-story building must support vertical gravity loads while undergoing large lateral drifts associated with deflections of the vertical seismic force resisting system and deflections of the flexible roof diaphragm. Analyzing the behavior of these gravity columns is complex since not only is there an interaction between compression and bending, but also the boundary conditions are not perfectly pinned or fixed. In this research, the behavior of steel columns that are square hollow structural sections (HSS) is investigated for stability using three design methods: elastic design, plastic hinge design, and pinned base design. First, for elastic design, the compression and flexural strength of the HSS columns are calculated according to the AISC specifications, and the story drift ratio that causes the interaction equation to be violated for varying axial force demands is examined. Then, a simplified design procedure is proposed; this procedure includes a modified interaction equation applicable to HSS column design based on a parameter, Pnh/Mn, and a set of design charts are provided. Second, a plastic hinge design is grounded in the concept that a stable plastic hinge makes the column continue to resist the gravity load while undergoing large drifts. Based on the available test data and the analytical results from finite element models, three limits on the width to thickness ratios are developed for steel square HSS columns. Lastly, for pinned base design, the detailing of a column base connection is schematically described. Using FE modeling, it is shown that it is possible to create rotational stiffness below a limit such that negligible moment develops at the column base. All the design methods are demonstrated with a design example / Master of Science / One-story buildings are one of the most economical types of structures built for industrial, commercial, or recreational use. During an earthquake, columns in a one-story building must support vertical gravity loads while undergoing large lateral displacements, referred to as story drift. Vertical loads cause compression forces, and lateral drifts produce bending moments. The interaction between these forces makes it more complex to analyze the behavior of these gravity columns. Moreover, since the column base is not perfectly fixed to the ground, there are many boundary conditions applicable to the column base depending on the fixity condition. For these reasons, the design for columns subjected to lateral drifts while supporting axial compressive forces has been a growing interest of researchers in the field. However, many researchers have focused more on wide-flange section (I-shape) steel columns rather than on tube section columns, known as hollow structural section (HSS) steel columns. In this research, the behavior of steel square tube section columns is investigated for stability using three design methods: elastic design, plastic hinge design, and pinned base design. First, for elastic design, the compression and flexural strength of the HSS columns are calculated according to current code equations, and the story drift that causes failure for varying axial force demands is examined. Then, a simplified design procedure is proposed including design charts. Second, a plastic hinge design is grounded in the concept that controlled yielding at the column base makes the column continue to resist the gravity load while undergoing large drifts. Based on the available test data and results from computational models, three limits on the width to thickness ratios of the tubes are developed. Lastly, for pinned base design, concepts for detailing a column base connection with negligible bending resistance is schematically described. Using a computational model, it is shown that the column base can be detailed to be sufficiently flexible to allow rotation. All the design methods are demonstrated with a design example.