Increasing use of rock materials like shale in building, roofing, embankment filling, brick manufacturing, and in other civil structure application makes it an important rock to consider in construction engineering. Knowledge of thermal and physical properties of shale as building material is required to predict the rock's strength and permanence against weathering. Inconsistent heat capacity of anisotropic rock can result in differential heat flow. This tendency can expand the building materials leading to reduction in strength and initiate disintegration. Authors have studied various thermo-physical properties of anisotropic shale from Tennessee, which is commonly used as building stones and bricks. Experiment was designed to measure the basic thermal property, 'heat capacity' of shale. Series of laboratory tests including durability, strength, specific gravity, moisture content, and porosity were conducted to determine the physical and mechanical behavior of the samples. Results indicated that properties like porosity, strength and heat capacity varied significantly within samples, where as specific gravity and moisture content yielded steady values. Multivariate regression analysis was performed to evaluate possible correlations among the tested properties. Strong positive relationship was evident between heat capacity, and porosity. Heat capacity and Unconfined Compressive Strength of shale were inversely related. This study emphasized that physical and thermal properties of shale are directly linked with strength and durability of the rock mass.

Characterization of rock masses and evaluation of their mechanical properties are important and challenging tasks in rock mechanics and rock engineering. Since in many cases rock quality designation (RQD) is the only rock mass classification index available, this paper outlines the key aspects on determination of RQD and evaluates the empirical methods based on RQD for determining the deformation modulus and unconfined compressive strength of rock masses. First, various methods for determining RQD are presented and the effects of different factors on determination of RQD are highlighted. Then, the empirical methods based on RQD for determining the deformation modulus and unconfined compressive strength of rock masses are briefly reviewed. Finally, the empirical methods based on RQD are used to determine the deformation modulus and unconfined compressive strength of rock masses at five different sites including 13 cases, and the results are compared with those obtained by other empirical methods based on rock mass classification indices such as rock mass rating (RMR), Q-system (Q) and geological strength index (GSI). It is shown that the empirical methods based on RQD tend to give deformation modulus values close to the lower bound (conservative) and unconfined compressive strength values in the middle of the corresponding values from different empirical methods based on RMR, Q and GSI. The empirical methods based on RQD provide a convenient way for estimating the mechanical properties of rock masses but, whenever possible, they should be used together with other empirical methods based on RMR, Q and GSI. (C) 2016 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting by Elsevier B.V.

This research investigates complete recycling and utilization of waste concrete to produce new structural concrete through geopolymerization. The investigation was conducted through both macro-and micro/nano-scale studies. First the geopolymer paste synthesized using a mixture of waste concrete fines (WCF) and class F fly ash (FA) as the source material and a mixture of NaOH solution (N) and Na2SiO3 solution (SS) as the alkaline activating agent was studied. Various NaOH concentrations, SS/N ratios, and WCF contents were used to produce geopolymer paste specimens in order to study their effect on the properties of the geopolymer paste. Uniaxial compression tests were conducted to measure the strength of the geopolymer paste specimens. X-ray diffraction (XRD), scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDX), and Fourier transform infrared spectroscopy (FTIR) analyses were performed to investigate the micro/nano-structure, morphology and phase/surface elemental compositions of the geopolymer paste and the effect of calcium (Ca) on them. The results indicate that by using 10 M NaOH solution, SS/N of 2 and 50% WCF, the highest geopolymer paste strength can be obtained. Second, the interfacial transition zones (ITZs) between geopolymer (GP) and recycled aggregates (RA) were studied. Considering that RA consist of the stone particles and the attached paste/mortar from the original ordinary Portland cement (OPC) concrete, both the ITZs between GP and natural aggregate (NA) and those between GP and residual OPC paste/mortar (ROPM) were studied. For comparison, the ITZs between OPC paste and NA and those between OPC paste and ROPM were also investigated. 4-point bending tests were conducted to measure the bonding strength of the different types of ITZs at water to solid (W/S) ratio of 0.30, 0.35 and 0.40 for the geopolymer and OPC pastes after 7 and 14 days curing, respectively. SEM imaging was performed to investigate the microstructure of the ITZs. The results indicate that when NA is used, the bonding strength of both the GP-NA and OPC-NA ITZs decreases with higher water to solid (W/S) ratio. When ROPM is used, higher W/S ratio leads to smaller bonding strength for the GP-ROPM ITZ but greater bonding strength for the OPC-ROPM ITZ. Based on the measured bonding strength values for NA- and ROPM-based ITZs, the bonding strength of the GP-RA and OPC-RA ITZs was estimated by considering the average area coverage of ROPM on the RA surface. The GP-RA ITZ has the highest bonding strength among the different ITZs, implying the great potential for utilizing waste concrete (both the WCF and the RA) to produce geopolymer concrete. Third, based on the studies on geopolymer paste and ITZs, geopolymer concrete (GPC) was produced and studied using WCF and FA as the cementitious material and RA as the aggregate. For comparison, GPC using NA was also produced and studied at similar conditions. Various NaOH concentrations, SS/N ratios, and cement (WCF and FA) to aggregate (C/A) ratios were used to produce GPC specimens in order to study their effect on the behavior of GPC. The effect of water content and curing temperature on the initial setting time and 7-day unconfined compressive strength (UCS) of the GPC was also studied. The results show that the GPC produced from RA has higher UCS than the GPC from NA at both room curing temperature and 35°C curing temperature. Based on this study, it can be concluded that waste concrete can be completely recycled and used to produce new structural concrete based on the geopolymerization technology. Fourth, considering that the Si/Al and Na/Al ratios have great effect on the geopolymerization process and the properties of the final geopolymer product, a study was conducted on copper mine tailings (MT)-based geopolymer containing different amount of aluminum sludge (AS). The results indicate that by including AS and utilizing appropriate amount of NaOH, the UCS can be increased significantly. The main reason is because the addition of AS along with utilization of appropriate amount of NaOH makes both the Si/Al and Na/Al ratios reach the optimum values for geopolymerization, leading to higher degree of geopolymerization and more compact geopolymer microstructure. It is noted that although this study is not directly on waste concrete, it provides useful information for optimizing the design on complete recycling and utilization of waste concrete to produce new GPC. Finally, to better understand the effect of Ca on the geopolymerization process and the properties of geopolymer, molecular dynamics (MD) simulations were performed on geopolymer at different Ca contents. The molecular models at different Ca contents were constructed and uniaxial compression test was then performed on the numerical specimens. The results indicate that MD simulation is an effective tool for studying the effect of Ca on the properties of geopolymer at nano-scale.

Παρουσιάζεται μία εναλλακτική μέθοδος έμμεσου προσδιορισμού της θλιπτικής (μονοαξονικής) αντοχής των πετρωμάτων με βάση μία τροποποιημένη μορφή της δοκιμής επιφανειακής διείσδυσης. Χρησιμοποιήθηκαν δύο έμβολα με σφαιρικά άκρα με ακτίνες 1,585mm και 5mm. Τα αποτελέσματα συγκρίνονται με αυτά της διαδεδομένης μεθόδου σημειακής φόρτισης. Αποδεικνύεται πειραματικά ότι για τα τρία ασβεστολιθικά πετρώματα που μελετήθηκαν, η δοκιμή επιφανειακής διείσδυσης δίνει σημαντικά ακριβέστερα αποτελέσματα και μπορεί να εφαρμοστεί τόσο στο εργαστήριο όσο και στο πεδίο. Επιπλέον αποδείχθηκε ότι η δοκιμή προσφέρει την δυνατότητα μη καταστροφικού ελέγχου των δοκιμίων ιδιαίτερα με το άκρο με την μικρή σφαίρα. / An alternative indirect method to determine the unconfined compressive strength of rocks based on a modified Indentation (Punch) test is presented. Two indenters with spherical tips of 1.585mm and 5mm were used. The results are compared with those of the Point Load test that is commonly used in practice. It is experimentally proved that for the three calcareous rock materials tested, this method gives significantly more accurate results and can be applied to the laboratory as well as in situ. In addition it has been proved that this test offers the possibility of non destructive testing especially when the small spherical tip is used.

<p> The central theme of the study is to identify strength-stiffness correlations for chemically treated subgrade soils in Indiana. This was done by conducting Unconfined Compression (UC) tests and resilient modulus tests for soils collected at three different sites, namely : US 31, SR 37 and I-65. At each site, soil samples were obtained from 11 locations at 30 ft spacing. The soils were treated in the laboratory with cement, using the same proportions used for construction, and cured for 7 and 28 days before testing. Results from the UC tests were compared with the resilient modulus results that were available. No direct correlation was found between resilient modulus and UCS parameters for the soils investigated in this study. A brief statistical analysis of the results was conducted, and a simple linear regression model involving the soil characteristics (plasticity index, optimum moisture content and maximum dry density) along with UCS and resilient modulus parameters was proposed.  </p>

The objective of this research was to measure and analyze the long-term modulus values of cement-treated base (CTB) layers constructed in Utah using microcracking. Because modulus values of pavement layers are among the most influential inputs affecting mechanistic-empirical pavement design, obtaining reasonable estimates of modulus values is critical. Testing was performed with a portable falling-weight deflectometer, also called a lightweight deflectometer, and modulus values were backcalculated with the computer program BAKFAA. Testing occurred at five asphalt pavement sites in northern Utah, where reconstruction with full-depth reclamation and cement stabilization, in the form of cement slurry, was performed approximately 2 to 14 years previously. Unconfined compressive strength (UCS) data collected for the CTB materials during earlier projects were compiled for all five sites. The correlation between backcalculated CTB modulus values, which ranged from 42 to 433 ksi, and 7-day UCS values, which ranged from 366 to 559 psi, was analyzed, and uniformity and sensitivity analyses were performed. Based on the results of this research, a new correlation is proposed for estimating the long-term modulus values of microcracked CTB layers constructed in a seasonally cold climate, such as northern Utah. For an average 7-day UCS of 450 psi, a CTB modulus value of 114 ksi would be estimated using this correlation, whereas a much higher modulus value of 630 ksi would be estimated from an existing correlation chart that was published in 1972 before microcracking was developed as a CTB construction practice. The results of the uniformity analyses indicate that statistically significant spatial variability in the CTB modulus values exists at each site. In comparison to a proposed maximum threshold coefficient of variation of 40 percent presented in the literature for aspects of CTB construction, the CTB modulus at all of the sites would be characterized as having low uniformity, with values ranging from 42.9 to 90.3 percent. The results of the sensitivity analyses indicate that backcalculated CTB modulus values are sensitive to typical deviations from design values that may occur in pavement layer thicknesses and suggest that CTB modulus estimation errors may range from -22,561 to 62,097 psi, or -3.73 to 10.81 percent, for pavements similar to those studied in this research when the actual asphalt and CTB layer thicknesses are different than the assumed values by up to 0.25 or 0.50 in., respectively.

Yes / This paper examines the impacts of clay mineralogy on the effectiveness of lime stabilisation at different temperatures. A comprehensive experimental programme was conducted to track down the evolution of lime-clay reactions and their durations through monitoring the evolution of strength gain at predetermined times using the Unconfined Compressive Strength (UCS) test. The study examined clays with different mineralogy compositions comprising Na+ Bentonite and Ball (Kaolinite) clay. Four different clays were tested including 100% bentonite, 100% Ball clay and two clay mixtures with ratios of 1:1 and 1:3 by mass of bentonite to Ball clay. All clays were treated using a range of lime content up to 25% and cured for a period of time up to 672 h at two different temperatures of 20 and 40 °C. The results showed that the continuity of the fast phase (stage 1) of strength gain was dependent on the availability of lime in particular at the higher temperature. Whereas, for the same lime content, the duration of the fast phase and the kinetic of strength gain were significantly related to the clay mineralogy and curing temperature. Except for the initial strength gain at 0 h curing time, the lime-treated Ball clay specimens at 20 °C appeared to show no strength gain throughout the curing period that extended up to 672 h. However, when curing occurred at 40 °C, the no strength gain stage only lasted for 72 h after which a gradual increase in the strength was observed over the remaining curing period of time. The addition of Bentonite to Ball clay succeeded in kicking off the strength gain after a short period of curing time at both curing temperatures.

Cemented paste backfill (CPB) technology is widely used in the mining industry as an effective means of tailings disposal. CPB is a mixture of tailings, binder, water, and additional admixtures when required. It is prepared in a mixing plant on the ground surface and then transported into the mine cavities through pipelines either by gravity and/or using pumps. To ensure efficiency during transportation and avoid pipe clogging (which can cause unnecessary delays and loss of productivity), fresh CPB must have sufficient flowability. To achieve that, high-range water reducing admixtures, also known as superplasticizers, are usually added to the CPB during mixing. These admixtures are widely used in the construction industry due to their ability to improve flowability without undermining other important engineering properties. However, their influence on the rheology, mechanical strength and environmental performance (reactivity and permeability) of CPB is not fully understood. Thus, experimental studies were conducted to investigate the effects of superplasticizers on the performance properties of cemented paste backfill at different curing temperatures. Yield stress and viscosity of fresh CPB cured for 0, 1, 2, and 4 hours were measured using a vane shear device and a Brookfield Viscometer respectively. Unconfined compressive strength (UCS) of samples cured for 1, 3, 7, and 28 days was determined in accordance with ASTM - C39. Superplasticizer contents were varied as 0%, 0.125%, and 0.25% of the total weight of the CPB. Preparations and curing of the specimens were performed at controlled conditions of 2, 20, and 35 °C to investigate the effect of ambient or curing temperatures. To have a better understanding of the environmental performance of CPB containing superplasticizer, reactivity, and hydraulic conductivity up to 90 days of curing were also investigated. The reactivity was measured using oxygen consumption test while hydraulic conductivity was measured using flexible wall permeability test. Microstructural analyses (thermogravimetric analyses, X-Ray diffraction, and mercury intrusion porosimetry) and monitoring tests (pH, zeta potential, electrical conductivity, and matric suction) were carried out to understand the principles behind the changes of the observed properties. The obtained results show that superplasticizer dosage and temperature variation have significant effects on the rheology, strength development, hydraulic conductivity and reactivity of the CPB. The polycarboxylic ether-based superplasticizer significantly reduces the yield stress and viscosity by creating strong electrostatic repulsion between the solid particles in the CPB and by steric hinderance. The CPB containing the superplasticizer remains fluid for longer period (as compared with the CPB without superplasticizer) due to the retardation of binder hydration. However, high curing temperature induces faster cement hydration, which thickens the fresh CPB. The unconfined compressive strength (UCS) of the CPB containing superplasticizer was observed to be lower in the early age (up to 7 days), which is also attributed to retardation of the binder hydration. At later ages, the superplasticizer improves the mechanical strength as the binder hydration accelerates and the solid particles self-consolidate. Coupled THMC processes in the CPB showed the role played by the changes in electrical conductivity, volumetric water content, matric suction, and temperature on the development of mechanical strength of the CPB containing superplasticizer. Similarly, addition of the superplasticizer in the CPB decreases both the hydraulic conductivity and reactivity of CPB, thus improving its environmental performance. The improvement is largely attributed to enhanced binder hydration and self-consolidation which decrease the porosity of the CPB. Increasing the curing temperature was found to magnify the improvement of the CPB properties by inducing faster binder hydration. The findings from this study will undoubtedly inform the design of CPB structure with better mechanical stability and environmental performance.

Natural soils in work-sites are sometimes detrimental to the construction of engineering projects. Problematic soils such as soft and expansive soils are a real source of concern to the long-term stability of structures if care is not taken. Expansive soils could generate immense distress due to their volume change in response to a slight change in their water content. On the other hand, soft soils are characterised by their low shear strength and poor workability. In earthwork, replacing these soils is sometimes economically and sustainably unjustifiable in particular if they can be stabilised to improve their behaviour. Several techniques have evolved to enable construction on problematic soils such as reinforcement using fibre and planar layers and piled reinforced embankments. Chemical treatment using, e.g. lime and/or cement is an alternative method to seize the volume change of swelling clays. The use of lime as a binding agent is becoming a popular method due to its abundant availability and cost-effectiveness. When mixed with swelling clays, lime enhances the mechanical properties, workability and reduces sensitivity to absorption and release of water. There is a consensus in the literature about the primary mechanisms, namely cation exchange, flocculation and pozzolanic reaction, which cause the changes in the soil characteristics after adding lime in the presence of water. The dispute is about whether these mechanisms occur in a sequential or synchronous manner. More precisely, the controversy concerns the formation of cementitious compounds in the pozzolanic reaction, whether it starts directly or after the cation exchange and flocculation are completed. The current study aims to monitor the signs of the formation of such compounds using a geotechnical approach. In this context, the effect of delayed compaction, lime content, mineralogy composition, curing time and environmental temperature on the properties of lime-treated clays were investigated. The compaction, swelling and permeability, and unconfind compression strength tests were chosen to evaluate such effect. In general, the results of the geotechnical approach have been characterised by their scattering. The sources of this dispersion are numerous and include sampling methods, pulverisation degree, mixing times and delay of compaction process, a pre-test temperature and humidity, differences in dry unit weight values, and testing methods. Therefore, in the current study, several precautions have been set to reduce the scattering in the results of such tests so that they can be used efficiently to monitor the evolution in the properties that are directly related to the formation and development of cementitious compounds. Four clays with different mineralogy compositions, covering a wide range of liquid limits, were chosen. The mechanical and hydraulic behaviour of such clays that had been treated by various concentrations of lime up to 25% at two ambient temperatures of 20 and 40oC were monitored for various curing times. The results indicated that the timing of the onset of changes in mechanical and hydraulic properties that are related to the formation of cementitious compounds depends on the mineralogy composition of treated clay and ambient temperature. Moreover, at a given temperature, the continuity of such changes in the characteristics of a given lime-treated clay depends on the lime availability.

Yes / This paper focuses on monitoring the evolution of lime-clay reactions using geotechnical parameters as a function of lime content and environmental temperature. Lime contents of 5, 7, 9, 11 and 13% by dry weight of expansive clay powder were added to prepare lime-clay specimens. The specimens were prepared at the same dry unit weight of 12.16 kN/m3 and moisture content of 40% except for tests aimed at the determination of dry unit weight as a function of mellowing period. Prepared specimens were mellowed or cured at two different ambient temperatures of 20 °C and 40 °C. Results attained from Unconfined Compressive Strength and permeability tests were employed to assess the impact of lime content on the mechanical and hydraulic properties of lime treated expansive clays. The results revealed that at the beginning, the rate of strength gain is remarkably fast for a particular period of time which is dependent on lime content. Furthermore, the strength gain on specimens cured at 40 °C is 8 times higher than that observed on specimens cured at 20 °C which highlights significant effect for the environmental temperature on accelerating the chemical reactions. Reduced dry unit weight due to increased resistance to compactability is observable with increasing lime content and higher environmental temperature. Accelerated pozzolanic reaction at higher environmental temperature resulted in permeability coefficient of specimens mellowed for 24 h at 40 °C to be higher than those mellowed at 20 °C. The results also highlighted that the permeability coefficient would be relatively stable when expansive clays were treated with small amounts of lime e.g. 5%.