Natural soils in work-sites are sometimes detrimental to the construction of engineering projects. Problematic soils such as soft and expansive soils are a real source of concern to the long-term stability of structures if care is not taken. Expansive soils could generate immense distress due to their volume change in response to a slight change in their water content. On the other hand, soft soils are characterised by their low shear strength and poor workability. In earthwork, replacing these soils is sometimes economically and sustainably unjustifiable in particular if they can be stabilised to improve their behaviour. Several techniques have evolved to enable construction on problematic soils such as reinforcement using fibre and planar layers and piled reinforced embankments. Chemical treatment using, e.g. lime and/or cement is an alternative method to seize the volume change of swelling clays. The use of lime as a binding agent is becoming a popular method due to its abundant availability and cost-effectiveness. When mixed with swelling clays, lime enhances the mechanical properties, workability and reduces sensitivity to absorption and release of water. There is a consensus in the literature about the primary mechanisms, namely cation exchange, flocculation and pozzolanic reaction, which cause the changes in the soil characteristics after adding lime in the presence of water. The dispute is about whether these mechanisms occur in a sequential or synchronous manner. More precisely, the controversy concerns the formation of cementitious compounds in the pozzolanic reaction, whether it starts directly or after the cation exchange and flocculation are completed. The current study aims to monitor the signs of the formation of such compounds using a geotechnical approach. In this context, the effect of delayed compaction, lime content, mineralogy composition, curing time and environmental temperature on the properties of lime-treated clays were investigated. The compaction, swelling and permeability, and unconfind compression strength tests were chosen to evaluate such effect. In general, the results of the geotechnical approach have been characterised by their scattering. The sources of this dispersion are numerous and include sampling methods, pulverisation degree, mixing times and delay of compaction process, a pre-test temperature and humidity, differences in dry unit weight values, and testing methods. Therefore, in the current study, several precautions have been set to reduce the scattering in the results of such tests so that they can be used efficiently to monitor the evolution in the properties that are directly related to the formation and development of cementitious compounds. Four clays with different mineralogy compositions, covering a wide range of liquid limits, were chosen. The mechanical and hydraulic behaviour of such clays that had been treated by various concentrations of lime up to 25% at two ambient temperatures of 20 and 40oC were monitored for various curing times. The results indicated that the timing of the onset of changes in mechanical and hydraulic properties that are related to the formation of cementitious compounds depends on the mineralogy composition of treated clay and ambient temperature. Moreover, at a given temperature, the continuity of such changes in the characteristics of a given lime-treated clay depends on the lime availability.

yes / A comprehensive experimental programme was performed with the focus on assessing the effects of compaction delay and ambient temperature on the physical, mechanical and hydraulic properties of lime treated expansive clays. Specimens were mellowed for a period of 0, 3, 6, 12, 24 and 48 h at two different temperatures of 20°C and 40°C prior to being compacted, tested and/or cured for up to 28 days for evaluating the impacts on long-term strength development. All specimens were prepared with the same dry unit weight of 12.16 kN/m3 and moisture content of 40% except for tests aimed at determining dry unit weight as a function of mellowing period. The results revealed that as the mellowing duration increased the dry unit weight declined remarkably at both temperature within the first 12 h. In addition, higher reduction rate was observed when specimens were mel-lowed at a temperature of 40°C. A 97% reduction in swelling pressure was obtained when the specimens were compacted upon mixing (zero hour mellowing period) and left to cure for 24 h prior to testing. Permeability coefficient of lime treated expansive clays was increased by up to 40 times when compaction was delayed for 24 h or when specimens were mellowed at 40°C. Specimens mellowed at a temperature of 40°C showed rela-tively stable values of permeability coefficient over the measurement period which could be attributable to accelerated pozzolanic reaction. The Unconfined Compressive Strength tests revealed that strength of lime treated expansive clays is significantly affected by compaction delay. An increase of 234% and 282% in the Unconfined Compressive Strength was achieved after 24 h of mixing with no compaction delay at 20°C and 40°C respectively. Gradual long-term gain in strength was observable within the 28 days post mixing but the rate of strength gain becomes slower and independent of temperature after the first 24 h of mixing. The results sug-gested that the four key reaction mechanisms occur concurrently with the first 12–24 h after lime addition recognized as being the most crucial period of time. Damaging the cementitious compounds by delayed com-paction is harmful to strength and restraining of swelling potential of lime treated expansive clays.

The specific objectives of this research were to quantify the effects of certain environmental factors on the relative strength loss of soil-cement subjected to compaction delay and to develop a numerical tool that can be easily used by engineers and contractors for determining a maximum compaction delay time for a given project. These objectives were addressed through extensive laboratory work and statistical analyses. The laboratory work involved testing an aggregate base material and a subgrade soil, each treated with two levels of cement. Environmental factors included in the experimentation were wind speed, temperature, and relative humidity, and three levels of each were evaluated in combination with varying compaction delay times. The primary response variables in this research were relative compaction and relative strength. The findings indicate that relative strength is sensitive to variability among the selected independent variables within the ranges investigated in this research, while relative compaction is not. Inferring relative strength from relative compaction is therefore not a reliable approach on soil-cement projects. Consistent with theory, higher wind speed, higher air temperature, lower relative humidity, and higher compaction delay time generally result in lower relative strength. With the nomographs developed in this research, the maximum delay time permitted for compaction of either a base or subgrade material similar to those tested in this research can be determined. Knowing in advance how much time is available for working the soil-cement will help contractors schedule their activities more appropriately and ultimately produce higher quality roads. When acceptable compaction delays are not obtainable due to adverse environmental conditions, a contractor may consider using set retarder, mixing at water contents above OMC, or constructing at night as possible solutions for achieving target relative strength values.