This work deals with the topic "Systems with wall heating". On this theme is elaborated theoretical part. Further experimental part, which deals with the measurement of wall heating and comparing the results with the software CalA. Subsequently, this topic is applied to the specified building in which the wall heating, among other things dealt with. The project addresses the design of central heating, water heating, water heater design power units and air tempering lawn for future newly built free-standing facilities football club. The project is designed in two versions. In the first variant of the heat source heat pumps air-water. In the second variant is the heat source hot water pipe which is connected to transfer water-water station with plate heat exchangers.

The subject of this diploma thesis is the elaboration of documentation for the construction of a hotel with a restaurant in Rožnov pod Radhoštěm. The building is designed for short-term accommodation of 50 people. The building is functionally divided into a hotel part and a restaurant part. It is a detached object L-shaped building. The building is designed as a classic building with masonry system. The hotel part is designed as a two-storey with masonry system and sloping roof. The restaurant part is designed as a two-storey with basement. This part is also from masonry system and with sloping roof. The building has 22 double rooms, 1 apartment for 4 people and 1 room for people with reduced mobility, restaurant and technical facilities.

The theme of this diploma thesis is to design heating of the flat house. The theoretical part of this diploma thesis is about exhaust gases paths. The calculation part of this diploma thesis contains the design of the heating system by panel heaters, floor convectors and underfloor heating system. The heat source is the system of cascade-connected gas condensing boilers. The rest of this part are the calculations of the preparation of hot water, design of hot water storage tank and another necessary equipment of the system. The part Project is about technical report and simulation of behaviour of underfloor heating system in various marginal conditions.

Master thesis high-rack storage area spo - selected parts of ctp covers technological studies throughout the building, the construction division, building and engineering structures, preparation of normal technology, mechanical engineering time and financial plan. Also master thesis focuses more on building a major object of the building, which is the storage, dispatch and administrative part of high-rack storage area spo. Building on this subject is further developed such documentation and other documents that complement and prescribe requirements for faster, easier, safer, better and technologically accurate realization of this phase.

The topic of my diploma thesis is air-water heat pumps. The diploma thesis contains three parts. In the first part I describe the theory of air-water heat pumps. In the second part I consider two variants of heating, hot water heating and pool water heating using air-water heat pumps in the family house, Révova. The third experimental part is focused on observation of operational process and calculation of heat factors of air-water heat pump while in the heating model. The calculated heating factors are then compared to the heating factors from the manufacturer's graph.

This diploma thesis deals with pressure losses in heating systems. The diploma thesis is divided into three sections. The first part is theoretical and deals with the occurrence of pressure losses. It discusses the properties of the fluid that affect pressure losses. It also deals with hydrodynamic phenomena, flow distribution, pressure loss distribution and its calculations. The aim of the second part, which is practical, was to create a heating project for a selected object. The object is a two-floor kindergarten building located in Velké Němčice. For this project, two heating variants were created. For the first variant, radiators and heating benches were designed and for the second variant, underfloor heating was installed in the building. The goal was to use a source which will gain heat mainly from renewable sources, so the air / water heat pump was chosen as the source of heat production. The project ends with a technical report. The third part of the thesis is dedicated to an experiment which purpose was to find out how the pressure losses of the connecting pieces are reacting to the change with the change of the heating water conditions (flow, temperature). Alongside, two pipes were created which differed in the type of connecting pieces so it allowed to compare how their pressure losses differ. Both pipes were connected by radial pressing, but the fittings differed in the quality of the brass, and therefore in the construction. Also, part of the experimental section of the diploma thesis is a description of the course of radial pressing of fittings from the Herz company.

The object of this master’s thesis is a newly-built mixed-use building in the town of Uherské Hradiště. It includes parking and office spaces, retail shops, and a coffee shop. The building is situated in a mildly sloping terrain near the town centre. It is a three-storey detached building with partial basement. The floor plan was created by joining several different-sized rectangles together. The mixed-use building is based on foundation pads and slabs. It is roofed with a warm flat roof and, above the first floor, with a green roof. The building consists of a cast-in-place reinforced concrete frame with columns and beams. The floor structure is composed of prestressed hollow core slabs. The external wall of the above-ground floors is made of hollow clay blocks and the basement external wall is made of permanent formwork. The wall of the lift shaft is built from reinforced concrete and the staircase is composed of precast reinforced concrete slabs. The external walls are insulated with contact thermal insulation system and in some parts there is timber cladding – ventilated façade with thermal insulation from glass wool. The thermal insulation of the basement and of the plinth is made of extruded polystyrene. The object is divided into several functional zones. On the ground floor there is a coffee shop, a copy shop, a stationery shop, and a bakery. On the first and second floors there are office spaces. In the basement there are technical facilities only. The main entrance of the object is from the northwest part of the plot. There the entrance to the car park is also located, situated to the northwest and southwest side of the plot. Bicycle stands and a place for recycling is also located there. Around the object there is a pavement from which there is wheelchair access to all of the functional zones.