Variable speed drive technology has advanced dramatically in the last 10 years with the advent of new power devices. In this study, a three phase induction motor drive using Insulated Gate Bipolar Transistors (IGBT) at the inverter power stage is introduced to implement speed and position control for the revolving stage in the Frederic Wood Theatre This thesis presents a solution to control a 3-phase induction motor using the Texas Instruments (TI) Digital Signal Processor (DSP) TMS320F2407A. The use of this DSP yields enhanced operations, fewer system components, lower system cost and increased efficiency. The control algorithm is based on the constant volts-per-hertz principle because the exact speed control is not needed. Reflective object sensors which are mounted on concrete frame are used to detect accurate edge position of revolving stage. The sinusoidal voltage waveforms are generated by the DSP using the space vector modulation technique. In order to satisfy some operating conditions for safe and agreeable operation, a look-up table, which is used to give command voltage and speed signals in software, is applied to limit the maximum speed and acceleration of the revolving stage. Meanwhile, a boost voltage signal is added at the low frequency areas to make the motor produce maximum output torque when starting. A test prototype is then built to validate the performance. Several tests are implemented into the IGBT drive to explore the reason for unacceptable oscillations in IGBT’s gate control signals. Improvement methods in hardware layout are suggested for the final design.

Variable speed drive technology has advanced dramatically in the last 10 years with the advent of new power devices. In this study, a three phase induction motor drive using Insulated Gate Bipolar Transistors (IGBT) at the inverter power stage is introduced to implement speed and position control for the revolving stage in the Frederic Wood Theatre This thesis presents a solution to control a 3-phase induction motor using the Texas Instruments (TI) Digital Signal Processor (DSP) TMS320F2407A. The use of this DSP yields enhanced operations, fewer system components, lower system cost and increased efficiency. The control algorithm is based on the constant volts-per-hertz principle because the exact speed control is not needed. Reflective object sensors which are mounted on concrete frame are used to detect accurate edge position of revolving stage. The sinusoidal voltage waveforms are generated by the DSP using the space vector modulation technique. In order to satisfy some operating conditions for safe and agreeable operation, a look-up table, which is used to give command voltage and speed signals in software, is applied to limit the maximum speed and acceleration of the revolving stage. Meanwhile, a boost voltage signal is added at the low frequency areas to make the motor produce maximum output torque when starting. A test prototype is then built to validate the performance. Several tests are implemented into the IGBT drive to explore the reason for unacceptable oscillations in IGBT’s gate control signals. Improvement methods in hardware layout are suggested for the final design.

Variable speed drive technology has advanced dramatically in the last 10 years with the advent of new power devices. In this study, a three phase induction motor drive using Insulated Gate Bipolar Transistors (IGBT) at the inverter power stage is introduced to implement speed and position control for the revolving stage in the Frederic Wood Theatre This thesis presents a solution to control a 3-phase induction motor using the Texas Instruments (TI) Digital Signal Processor (DSP) TMS320F2407A. The use of this DSP yields enhanced operations, fewer system components, lower system cost and increased efficiency. The control algorithm is based on the constant volts-per-hertz principle because the exact speed control is not needed. Reflective object sensors which are mounted on concrete frame are used to detect accurate edge position of revolving stage. The sinusoidal voltage waveforms are generated by the DSP using the space vector modulation technique. In order to satisfy some operating conditions for safe and agreeable operation, a look-up table, which is used to give command voltage and speed signals in software, is applied to limit the maximum speed and acceleration of the revolving stage. Meanwhile, a boost voltage signal is added at the low frequency areas to make the motor produce maximum output torque when starting. A test prototype is then built to validate the performance. Several tests are implemented into the IGBT drive to explore the reason for unacceptable oscillations in IGBT’s gate control signals. Improvement methods in hardware layout are suggested for the final design. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate