Spelling suggestions: "subject:"variablenumber airfoil"" "subject:"variablenumber irfoil""
1 |
Aerodynamic and Electromechanical Design, Modeling and Implementation Of Piezocomposite AirfoilsBilgen, Onur 02 September 2010 (has links)
Piezoelectrics offer high actuation authority and sensing over a wide range of frequencies. A Macro-Fiber Composite is a type of piezoelectric device that offers structural flexibility and high actuation authority. A challenge with piezoelectric actuators is that they require high voltage input; however the low power consumption allows for relatively lightweight electronic components. Another challenge, for piezoelectric actuated aerodynamic surfaces, is found in operating a relatively compliant, thin structure (desirable for piezoceramic actuators) in situations where there are relatively high external (aerodynamic) forces. Establishing an aeroelastic configuration that is stiff enough to prevent flutter and divergence, but compliant enough to allow the range of available motion is the central challenge in developing a piezocomposite airfoil. The research proposed here is to analyze and implement novel electronic circuits and structural concepts that address these two challenges.
Here, a detailed theoretical and experimental analysis of the aerodynamic and electromechanical systems that are necessary for a practical implementation of a piezocomposite airfoil is presented. First, the electromechanical response of Macro-Fiber Composite based unimorph and bimorph structures is analyzed. A distributed parameter electromechanical model is presented for interdigitated piezocomposite unimorph actuators. Necessary structural features that result in large electrically induced deformations are identified theoretically and verified experimentally. A novel, lightweight electrical circuitry is proposed and implemented to enable the peak-to-peak actuation of Macro-Fiber Composite bimorph devices with asymmetric voltage range.
Next, two novel concepts of supporting the piezoelectric material are proposed to form two types of variable-camber aerodynamic surfaces. The first concept, a simply-supported thin bimorph airfoil, can take advantage of aerodynamic loads to reduce control input moments and increase control effectiveness. The structural boundary conditions of the design are optimized by solving a coupled fluid-structure interaction problem by using a structural finite element method and a panel method based on the potential flow theory for fluids. The second concept is a variable-camber thick airfoil with two cascading bimorphs and a compliant box mechanism. Using the structural and aerodynamic theoretical analysis, both variable-camber airfoil concepts are fabricated and successfully implemented on an experimental ducted-fan vehicle. A custom, fully automated low-speed wind tunnel and a load balance is designed and fabricated for experimental validation. The airfoils are evaluated in the wind tunnel for their two-dimensional lift and drag coefficients at low Reynolds number flow. The effects of piezoelectric hysteresis are identified.
In addition to the shape control application, low Reynolds number flow control is examined using the cascading bimorph variable-camber airfoil. Unimorph type actuators are proposed for flow control in two unique concepts. Several electromechanical excitation modes are identified that result in the delay of laminar separation bubble and improvement of lift. Periodic excitation to the flow near the leading edge of the airfoil is used as the flow control method. The effects of amplitude, frequency and spanwise distribution of excitation are determined experimentally using the wind tunnel setup.
Finally, the effects of piezoelectric hysteresis nonlinearity are identified for Macro-Fiber Composite bimorphs. The hysteresis is modeled for open-loop response using a phenomenological classical Preisach model. The classical Preisach model is capable of predicting the hysteresis observed in 1) two cantilevered bimorph beams, 2) the simply-supported thin airfoil, and 3) the cascading bimorph thick airfoil. / Ph. D.
|
2 |
Multi-objective design optimization for high-lift aircraft configurations supported by surrogate modelingLi, Daxin 12 1900 (has links)
Nowadays, the competition among airlines seriously depend upon the saving operating
costs, with the premise that not to degrade its services quality. Especially in the face of increasingly
scarce oil resources, reducing fleets operational fuel consumption, is an important
means to improve profits.
Aircraft fuel economy is determined by operational management strategies and application
technologies. The application of technologies mainly refers to airplane’s engine performance,
Weight efficiency and aerodynamic characteristics. A market competitive aircraft
should thoroughly consider to all of these aspects.
Transport aircraft aerodynamic performance mainly is determined by wing’s properties.
Wings that are optimized for efficient flight in cruise conditions need to be fitted with
powerful high-lift devices to meet lift requirements for safe takeoff and landing. These
high-lift devices have a significant impact on the total airplane performance. The aerodynamic
characteristics of the wing airfoil will have a direct impact on the aerodynamic
characteristics of the wing, and the wing’s effective cruise hand high-lift configuration design
has a significant impact on the performance of transport aircraft. Therefore, optimizing
the design is a necessary airfoil design process.
Nowadays engineering analysis relies heavily on computer-based solution algorithms to investigate
the performance of an engineering system. Computational fluid dynamics (CFD)
is one of the computer-based solution methods which are more widely employed in aerospace
engineering. The computational power and time required to carry out the analysis increases
as the fidelity of the analysis increases. Aerodynamic shape optimization has become
a vital part of aircraft design in the recent years. Since the aerodynamic shape optimization
(ASO) process with CFD solution algorithms requires a huge amount of computational
power, there is always some reluctance among the aircraft researchers in employing
the ASO approach at the initial stages of the aircraft design. In order to alleviate this problem,
statistical approximation models are constructed for actual CFD algorithms. The fidelity
of these approximation models are merely based on the fidelity of data used to construct
these models. Hence it becomes indispensable to spend more computational power in order
to convene more data which are further used for constructing the approximation models.
The goal of this thesis is to present a design approach for assumed wing airfoils; it includes
the design process, multi-objective design optimization based on surrogate modelling. The
optimization design stared from a transonic single-element single-objective optimization
design, and then high-lift configurations were two low-speed conditions of multi-objective
optimization design, on this basis, further completed a variable camber airfoil at low speed
to high-lift configuration to improve aerodynamic performance. Through this study, prove a
surrogate based model could be used in the wing airfoil optimization design.
|
Page generated in 0.0986 seconds